• 열처리공학회지
• /
• 제36권2호
• /
• pp.61-68
• /
• 2023

Ti and Ti alloys are used in the automobile and aerospace industries due to their high specific strength and excellent corrosion resistance. However their application is limited due to poor formability at room temperature and high unit cost. In order to overcome these issues, dissimilarly jointed materials, such as cladding materials, are widely investigated to utilize them in each industrial field because of an enhanced plasticity and relatively low cost. Among various dissimilar bonding processes, the rolled cladding process is widely used in Ti alloys, but has a disadvantage of low bonding strength. Although this problem can be solved through post-heat treatment, the mechanical properties at the bonded interface are deteriorated due to residual stress generated during post-heat treatment. Therefore, in this study, the microstructure change and residual stress trends at the interfaces of Ti/Al cladding materials were studied with increasing post-heat treatment temperature. As a result, compared to the as-rolled specimens, no difference in microstructure was observed in the specimens after postheat treatment at 300, 400, and 500℃. However, a new intermetallic compound layer was formed between Ti and Al when post-heat treatment was performed at a temperature of 600℃ or higher. Then, it was also confirmed that compressive residual stress with a large deviation was formed in Ti due to the difference in thermal expansion coefficient and modulus of elasticity between Ti Grade II and Al 1050.

• Earthquakes and Structures
• /
• 제23권5호
• /
• pp.473-491
• /
• 2022

The research investigates experimentally the effect of confinement on structural behavior at the ends of beam-column in reinforced concrete (RC) frames. In the experimental study, five specimens consisting of 1/3-scaled RC frames having single-bay, representing the traditional deficiencies of existing buildings constructed without receiving proper engineering service is investigated. The RC frame specimens were produced to represent most of the existing buildings in Turkey that have damage potential. To decrease the probable damage to the existing buildings exposed to earthquakes, the carbon Textile Reinforced Mortar (TRM) strengthening technique (fully wrapping) was used on the ends of the RC frame elements to increase the energy dissipation and deformation capacity. The specimens were tested under reversed cyclic lateral loading with constant axial loads. They were constructed satisfying the weak column-strong beam condition and consisting of low-strength concrete, such as compressive strength of 15 MPa. The test results were compared and evaluated considering stiffness, strength, energy dissipation capacity, structural damping, ductility, and damage propagation in detail. Comprehensive investigations of these experimental results reveal that the strengthening of a brittle frame with fully-TRM wrapping with non-anchored was effective in increasing the stiffness, ductility, and energy dissipation capacities of RC bare frames. It was also observed that the frame-only-retrofitting with an infill wall is not enough to increase the ductility capacity. In this case, both the frame and infill wall must be retrofitted with TRM composite to increase the stiffness, lateral load carrying, ductility and energy dissipation capacities of RC frames. The presented strengthening method can be an alternative strengthening technique to enhance the seismic performance of existing or moderately damaged RC buildings.

• Geomechanics and Engineering
• /
• 제33권1호
• /
• pp.29-40
• /
• 2023

Xanthan gum and starch compound biopolymer (XS), an environmentally friendly soil-binding material produced from natural resources, has been suggested as a slope protection material to enhance soil strength and erosion resistance. Insufficient wet strength and the consequent durability concerns remain, despite XS biopolymer-soil treatment showing high strength and erosion resistance in the dried state, even with a small dosage of soil mass. These concerns need to be solved to improve the field applicability and post-stability of this treatment. This study explored the utilization of an alkaline-based cation crosslinking method using calcium hydroxide and sodium hydroxide to induce non-thermal gelation, resulting in the enhancement of the wet strength and durability of biopolymer-treated soil. Laboratory experiments were conducted to assess the unconfined compressive strength and cyclic wetting-drying durability performance of the treated soil using a selected recipe based on a preliminary gel formation test. The results demonstrated that the uniformity of the gel structure and gelling time varied depending on the ratio of crosslinkers to biopolymer; consequently, the strength of the soil was affected. Subsequently, site soil treated with the recipe, which showed the best performance in indoor assessment, was implemented on the field slope at the bridge abutment via compaction and pressurized spraying methods to assess feasibility in field implementation. Moreover, the variation in surface soil hardness was monitored periodically for one year. Both slopes implemented by the two construction methods showed sufficient stability against detachment and scouring, with a higher soil hardness index than the natural slope for a year.

• 한국군사과학기술학회지
• /
• 제26권1호
• /
• pp.1-9
• /
• 2023

The skin structure of sensor pod mounted on the exterior of aircraft can be exposed to the acoustic dynamic load and static load such as aerodynamic pressure and inertial load during flight. Fatigue life prediction of structural model under acoustic load should be performed and also differential stiffness of model modified by static load should be considered. The acoustic noise test spectrum of MIL-STD-810G was applied to the structural model and the stress response power spectral density (PSD) was calculated. The frequency response analysis was performed with or without prestress induced by inplane static load, and the response spectrum was compared. Time series data was generated using the calculated PSD, and the time and frequency domain fatigue life were predicted and compared. The variation of stress response spectrum due to static load and predicted fatigue life according to the different structural model considering mean stress were examined and decreasing fatigue life was observed in the model with prestress of compressive static load.

• 한국건설순환자원학회논문집
• /
• 제11권1호
• /
• pp.48-54
• /
• 2023

본 연구에서는 금속성분을 다량 함유한 전기로산화슬래그(EOS)를 골재로 활용한 콘크리트에 도전성이 높은 카본계 재료를 혼입하여 현장적용이 가능한 EMP 차폐 콘크리트의 최적배합을 도출하고자 기초적인 물성과 두께별 EMP 차폐성능을 평가하였다. 평가결과 슬럼프는 카본섬유(CF)의 혼입량이 증가할수록 저하, 밀드카본(MCF) 혼입시 증가하는 것을 확인할 수 있었다. 압축강도는 EOS가 NA에 비해 강도를 증진시키는 것을 확인할 수 있었으며, CF 및 MCF 혼입시 강도가 저하되는 것을 확인할 수 있었다. EMP 차폐 측정결과 두께가 증가할수록 차폐율이 증가하였으며, 도전성 재료의 첨가량보다 도전성 재료의 종류 및 시험체의 두께가 차폐율 증가에 영향력이 더 큰 것을 확인할 수 있었다. 종합적으로 비교평가를 진행한 결과 EMP 차폐 콘크리트 배합으로 EOS CF 0.2가 적합한 것으로 사료된다.

• 한국지반공학회논문집
• /
• 제23권3호
• /
• pp.41-50
• /
• 2007

본 논문에서는 실트 함유율이 높은 모래에 대한 정규압밀 등방배수 및 비배수 삼축압축시험(NCIU 및 NCID) 결과를 나타내었다. 유효구속응력 $100\sim400kpa$하에서 실트 함유율이 63%인 낙동강 모래 시료를 사용하여 실험을 실시하였다. 실험결과, 모래질 실트는 초기에는 압축이 되지만 전체적인 응력-변형률 곡선에서 최종적으로 체적팽창반응을 보였다. 모래질 실트의 거동은 낮은 소성 특성으로 인하여 점토와 모래보다 비하여 그 특성을 묘사하기가 어려웠다. 특히, 시료는 파괴 후 전단과정에서 팽창현상을 보였다. 모래질 실트의 전단거동과 전단강도정수는 응력-변형률 거동과 Mohr-Coulomb 파괴규준에 의하여 결정되는데, 전단거동은 파괴 후 변형률 연화 경향과 같이 체적변화가 증가하는 것으로 관찰되었다. 본 논문에서 모래질 실트의 전단과정 동안에 발생되는 팽창거동은 모래 함유율 뿐만 아니라 저점착력을 가진 세립자의 함유율에 의해서도 달라졌다.

• 한국지반공학회논문집
• /
• 제25권10호
• /
• pp.5-15
• /
• 2009

본 논문에서는 옥천 및 창녕지역에서 총 24회 수행한 암반앵커 현장인발시험의 결과를 나타내었다. 시험앵커의 정착깊이는 1~6m로 서로다른 암반내에 설치하였다. 앵커의 대부분은 고강도 이형철근인 SD40-D51mm를 사용함으로써 다른 파괴가 일어나기 전에 암반파괴가 먼저 일어나도록 유도하여 암반의 인발저항력을 파악하고자 하였으며, 일부에서는 SD40-D32mm앵커를 설치하여 앵커의 파괴도 아울러 살펴보았다. 많은 시험에서 파괴는 항복에 이르는 극한하중까지 관찰할 수 있었으며, 암반파괴형상은 암반이 들어올려지면서 방사상으로 균열이 발달하는 형태를 나타내었다. 또한 시멘트그라우트와 텐던사이의 부착강도를 평가하고자 방식쉬이스가 설치된 앵커에 대해 실내실험을 실시하였다. 실험결과 텐던-그라우트 사이의 부착강도는 그라우트 일축압축강도의 18~25%로 나타났으며, 방식쉬이스에 의한 부착력 감소는 무시할 수 있을 정도로 작게 나타났다.

• 한국지반공학회논문집
• /
• 제24권4호
• /
• pp.67-78
• /
• 2008

본 연구에서는 시멘트의 고결효과를 정량적으로 파악하기 위하여 낙동강하상모래와 소량의 포틀랜드시멘트를 혼합하여 고결된 모래에 대하여 일축압축시험 및 배수조건과 비배수 조건의 삼축압축시험을 수행하였다. 시멘트혼합율의 증가에 따라 첨두강도 및 탄성계수는 증가하였고 시멘트의 결합력에 의하여 다일레이션 및 과잉간극수압이 억제되었으나 시멘트 결합력의 파괴 후 증가된 모래입자크기에 의하여 증가하였다. 그리고 배수조건의 응력-변형률 곡선은 연화거동이 나타났지만 비배수조건에서는 증가된 부(-)의 과잉간극수압에 의한 유효응력의 증가로 경화거동을 나타냈다. 각 조건에 대한 강도증가량의 예측을 위하여 선형을 가정한 다중회귀분석을 실시한 결과 제시된 경험식의 결정계수는 $0.81{\sim}0.91$로 나타나 신뢰성이 높은 것으로 평가되었으며 건조밀도의 경우 고결된 모래의 입도조건을 동시에 고려할 수 있어 고결된 모래의 강도를 결정하는데 중요한 변수로 분석되었다.

• 한국분말재료학회지
• /
• 제30권2호
• /
• pp.146-155
• /
• 2023

The Ti-6Al-4V lattice structure is widely used in the aerospace industry owing to its high specific strength, specific stiffness, and energy absorption. The quality, performance, and surface roughness of the additively manufactured parts are significantly dependent on various process parameters. Therefore, it is important to study process parameter optimization for relative density and surface roughness control. Here, the part density and surface roughness are examined according to the hatching space, laser power, and scan rotation during laser-powder bed fusion (LPBF), and the optimal process parameters for LPBF are investigated. It has high density and low surface roughness in the specific process parameter ranges of hatching space (0.06-0.12 mm), laser power (225-325 W), and scan rotation (15°). In addition, to investigate the compressive behavior of the lattice structure, a finite element analysis is performed based on the homogenization method. Finite element analysis using the homogenization method indicates that the number of elements decreases from 437,710 to 27 and the analysis time decreases from 3,360 to 9 s. In addition, to verify the reliability of this method, stress-strain data from the compression test and analysis are compared.

• 토지주택연구
• /
• 제14권2호
• /
• pp.137-145
• /
• 2023

본 연구에서는 매립석탄재를 이용한 CLSM의 실질적인 기술개발의 일환으로 매립석탄재의 입도분포 및 미립자 함량 등 물성에 따른 CLSM의 유동성, 블리딩 속도, 강도 등의 특성을 검토하였다. 그 결과 채취한 매립석탄재는 밀도 특성과 입도 분포가 다른 것으로 나타났으며 비산재의 양이 많고 혼합수를 많이 첨가한 시편의 경우 블리딩 비율이 기준을 만족하지 못하였고 압축강도 시험 결과, 4시간 동안 0.5MPa 이상의 강도발현은 단위결합재량이 200 이상인 반수석고를 사용한 시편의 경우 만족스러운 것으로 나타났다. 나머지 석고는 강도발현이 불량한 것으로 나타나 매립석탄재는 CLSM 소재로 활용이 가능할 것으로 판단되나 각 발전사의 회처리장에 매립된 석탄재의 물리화학적 특성을 규명하고 적용할 필요가 있다.