• Journal of Welding and Joining
• /
• 제5권1호
• /
• pp.42-56
• /
• 1987

Fatigue Fracture behaviors of the TIG-welded aluminum alloys, such as Al 2024-T4, A1 5050-0 and Al 7075-T7 were investigated when a crack propagated from tensile residual stress region and compressive residual stress region. The experimental values were compared with the values expected by the Forman equation. The experimental results are summarized as the following: (1) In case of fatigue crack propagation from residual stress region, the values predicted by Forman equation were Found to exactly corresponded to the experimental values. (2) When the stress intensityfactors affected by compressive residual stress, Kres, were greater than the stress intensity factors by minimum applied stresses. Kmin, the Forman equation was found to be improper to be applied directly, but the equation appeared to be proper, if the stress ratio was modified to zero. (3) The experimental results confirmed that residual stress was relaxed by repeated tensile loading and the relaxing trend was greater in case of compressive residual stress than that of tensile residual stress.

• 대한치과교정학회지
• /
• 제32권5호
• /
• pp.343-353
• /
• 2002

제1소구치 발치를 동반한 설측교정치료시 lingual K-loop archwire로 전치부 후방견인을 시 행한 경우 전치부 및 구치부에서 치조골에 발생하는 초기응력을 알아보기 위하여, K-loop의 vortical leg 길이는 15mm로 하고 편측당 350gm의 힘으로 활성화시 킨 후 상악궁 광탄성 모형의 응력동결을 시행하고 각 치아별로 절단하여 3차원 광탄성법으로 분석한 바 다음과 같은 결론을 얻었다. 1. 중절치의 근심면은 치관측일수록 더 큰 인장응력을 보였으며 원심면은 치관측일수록 더 큰 압축응력을 보였다. 순면에서는 치관측일수록 더 큰 인장응력을 보였으며 설면에서는 치근측일수록 더 큰 압축응력을 보였다 치근첨에서는 압축응력이 나타났다. 2. 측절치의 근심면에서는 치관측만 인장응력이 관찰되었고 원심면에서는 고른 압축응력을 보였다. 순면에서는 치관측일수록 더 큰 인장응력이 관찰되었고 설면에서는 치관측에서는 인장응력을, 치근측에서는 압축응력을 보였다. 치근첨에서는 압축응력이 관찰되었다. 3. 견치의 근심면은 치관측에서는 인장응력을, 치근측에서는 압축응력을 보였고 원심면은 인장응력을 보였다. 순면과 설면은 치관측일수록 큰 인장응력을 보였다. 순면보다 설면에서 더 큰 인장응력을 보였다. 치근첨에서는 압축응력이 관찰되었다. 4. 제2소구치는 근심면은 인장응력을 보이며 원심면은 치관측에서는 압축응력을, 치근측에서는 인장응력을 보였다. 협면은 치관측에서 압축응력을 보였으며, 설면은 치관측일수록 더 큰 인장응력이 관찰되었다. 치근첨에서는 인장응력을 보였다. 5. 제1대구치는 근원심면 모두에서 치관측일수록 더 큰 인장응력을 보였다. 협면에서는 응력이 나타나지 않았고, 설면은 치관측일수록 더 큰 인장응력이 관찰되었다. 협측치근들의 치근첨에서는 압축응력을, 구개측치근의 치근첨에서는 무응력을 보였다. 6. 제2대구치는 모든 치근의 치근첨에서 압축응력이 관찰되었다. 근심면은 치관측일수록 더 큰 압축응력을, 원심면은 치관측일수록 더 큰 인장응력을 보였다 협면은 치관측일수록 더 큰 인장응력을, 설면은 치관측일수록 더 큰 압축응력을 나타내었다. 따라서 전치부 후방견인시 transverse bowing effect는 뚜렷이 나타났으나, vertical bowing effect는 나타나지 않고 오히려 전치부가 함입되려는 응력이 발생하였다.

• Geomechanics and Engineering
• /
• 제14권2호
• /
• pp.203-209
• /
• 2018

Reliable estimation of compressive as well as tensile in-situ stresses is critical in the design and analysis of underground structures and openings in rocks. Kaiser effect technique, which uses acoustic emission from rock specimens under cyclic load, is well established for the estimation of in-situ compressive stresses. This paper investigates the Kaiser effect on marble specimens under cyclic uniaxial compressive as well as cyclic uniaxial tensile conditions. The tensile behavior was studied by means of Brazilian tests. Each specimen was tested by applying the load in four loading cycles having magnitudes of 40%, 60%, 80% and 100% of the peak stress. The experimental results confirm the presence of Kaiser effect in marble specimens under both compressive and tensile loading conditions. Kaiser effect was found to be more dominant in the first two loading cycles and started disappearing as the applied stress approached the peak stress, where felicity effect became dominant instead. This behavior was observed to be consistent under both compressive and tensile loading conditions and can be applied for the estimation of in-situ rock stresses as a function of peak rock stress. At a micromechanical level, Kaiser effect is evident when the pre-existing stress is smaller than the crack damage stress and ambiguous when pre-existing stress exceeds the crack damage stress. Upon reaching the crack damage stress, the cracks begin to propagate and coalesce in an unstable manner. Hence acoustic emission observations through Kaiser effect analysis can help to estimate the crack damage stresses reliably thereby improving the efficiency of design parameters.

• 한국안전학회지
• /
• 제19권4호
• /
• pp.8-13
• /
• 2004

The purpose of this paper is to investigate the welding residual stress distribution according to the constraint or non-constraint welding condition with titanium commonly using power station, aircraft, and ship. The measuring method of the residual stress was applied stress release rating method with strain gages and a potable strain meter. The x direction residual stress generally showed the tensile residual stress in case of res03int welding. On the other hand, the x direction residual stress under non-restraint welding were changed tensile stress into compressive stress on 15mm away from welding bead center. Also, the y direction residual stress generally showed the tensile residual stress in case of non-restraint welding and the y direction residual stress under restraint welding were changed tensile stress into compressive stress about 60mm away from welding bead center.

• E2M - 전기 전자와 첨단 소재
• /
• 제10권4호
• /
• pp.327-333
• /
• 1997

Experiments on mechanical fatigue were conducted using the specimens which were cut from hydrogen cooled generator(rated 22kV and 50OMW) stator windings. We have investigated the aged mechanism of mica/epoxy insulation systems under air or hydrogen by both the tensile and compressive loadings. The fracture of generator stator windings is generally affected by mechanical stress. Thus, the tensile strength test were conducted. In this case, the maximum strength and strain are quite different between sound and aged specimens. It is observed that low bonded interface parts of tapes generally have lower strength than those of normal tapes which causes stress. In order to estimate the effects of cyclic load by the electromagnetic forces while the generator starts/stops, the mechanical fatigue test was also conducted. It is confirmed that the equation of expected life depends on stress amplitude and number of cycles. Though the stress amplitude and number of cycles are very tiny, the tensile fatigue of aged specimens under hydrogen atmosphere is bigger than those under air. In the case of hydrogen atmosphere, the tensile stress gives bigger effect than the compressive one.

• 한국건설순환자원학회논문집
• /
• 제8권4호
• /
• pp.458-466
• /
• 2020

이 연구의 목적은 비정질 강섬유와 폴리아미드 섬유를 이용한 고성능 하이브리드 섬유보강 콘크리트의 압축 및 인장 거동을 평가하는 것이다. 이를 위하여 목표 압축강도 40MPa 및 60MPa 각각에 대해서 비정질 강섬유와 폴리아미드 섬유를 총 부피비로 1.0% 혼입한 고성능 하이브리드 섬유보강 콘크리트를 제작한 후 압축강도, 압축인성, 직접인장강도 및 응력-변형률 특징 등의 압축 및 인장 거동을 평가하였다. 그 결과, 고성능 하이브리드 섬유보강 콘크리트의 압축강도는 플레인 콘크리크보다 다소 감소하였으나, 압축인성, 압축인성 비, 직접인장강도는 크게 증가하는 것으로 나타났다. 또한 압축 및 인장 시험시 플레인 콘크리트는 최대응력 이후 취성파괴를 나타냈으나, HPHFRC는 변형연화 현상을 나타내어, 압축 및 인장 거동이 크게 개선되는 것으로 나타났다.

• 한국정밀공학회지
• /
• 제8권1호
• /
• pp.41-49
• /
• 1991

A knowledge of the resdual stress distribution at circumferential weldments can normally increase the accuracy of a fracture assessment in pipe line. In this paper, we present the measurements about the residual stress distributions at three kinds of circumferential butt welded pipes using the holl drilling strain gage method. By this experiment, we have obtined the following characteristics. At the inner surface of the pipe region near the center line of welding is under high tensile residual stress. However, as the distance from the center line of welding increases, the tensile component decreases and finally becomes compressive residual stress at region far away from the center line of welding. The longitudinal residual stress at the outer surface is compressive regardless of the diameter of pipe and the circumferential stress is changed from compressive to tensile as pipe diameter increases. The results also demonstrate that the residual stress is mainly caused by self-restraint bending force in the pipe welding.

• Structural Engineering and Mechanics
• /
• 제41권4호
• /
• pp.495-508
• /
• 2012

The strength theory of concrete is significant to structure design and nonlinear finite element analysis of concrete structures because concrete utilized in engineering is usually subject to the action of multi-axial stress. Experimental results have revealed that lightweight aggregate (LWA) concrete exhibits plastic flow plateau under high compressive stress and most of the lightweight aggregates are crushed at this stage. For the purpose of safety, therefore, in the practical application the strength of LWA concrete at the plastic flow plateau stage should be regarded as the ultimate strength under multi-axial compressive stress state. With consideration of the strength criterion, the ultimate strength surface of LWA concrete under multi-axial stress intersects with the hydrostatic stress axis at two different points, which is completely different from that of the normal weight concrete as that the ultimate strength surface is open-ended. As a result, the strength criteria aimed at normal weight concrete do not fit LWA concrete. In the present paper, a multi-axial strength criterion for LWA concrete is proposed based on the Unified Twin-Shear Strength (UTSS) theory developed by Prof Yu (Yu et al. 1992), which takes into account the above strength characteristics of LWA under high compressive stress level. In this strength criterion model, the tensile and compressive meridians as well as the ultimate strength envelopes in deviatoric plane under different hydrostatic stress are established just in terms of a few characteristic stress states, i.e., the uniaxial tensile strength $f_t$, the uniaxial compressive strength $f_c$, and the equibiaxial compressive $f_{bc}$. The developed model was confirmed to agree well with experimental data under different stress ratios of LWA concrete.

• Corrosion Science and Technology
• /
• 제20권6호
• /
• pp.484-490
• /
• 2021

Instrumented indentation testing has been widely used for residual stress measurement. The Knoop indentation is mainly selected for determining anisotropic mechanical properties and non-equibiaxial residual stress. However, the measurement of equibiaxial stress state and compressive residual stress on a specimen surface using Knoop indentation is neither fully comprehended nor unavailable. In this study, we investigated stress conversion factors for measuring Knoop indentation on equibiaxial stress state through indentation depth using finite element analysis. Knoop indentation was conducted for specimens to determine tensile and compressive equibiaxial residual stress. Both were found to be increased proportionally according to indentation depth. The stress field beneath the indenter during each indentation test was also analyzed. Compressive residual stress suppressed the in-plane expansion of stress field during indentation. In contrast, stress fields beneath the indenter developed diagonally downward for tensile residual stress. Furthermore, differences between trends of stress fields at long and short axes of Knoop indenter were observed due to difference in indenting angles and the projected area of plastic zone that was exposed to residual stress.

• 대한기계학회논문집
• /
• 제15권2호
• /
• pp.693-702
• /
• 1991

The existence of residual stress in the circumferential butt welded pipes is one of the most important problems concerning stress corrosion cracking in service. In this paper, the residual stress distributions in three kinds of circumferential butt welded pipes were measured by the hole drilling strain gage method and calculation using finite element method is performed and its results are compared with the experiments. At the inner surface of the pipe region near the center line of welding is under high tensile residual stress. However, as the distance from the center line of welding increases, the tensile component decreases and finally becomes compressive residual stress at region far away from the center line of welding. The longitudinal residual stress at the outer surface is compressive regardless of the diameter of pipe and the circumferential stress is changed rom compressive to tensile as pipe diameter increases. The results also demonstrate that the residual stress is mainly caused by self restraint bending force in the pipe welding.