• Journal of Korean Neurosurgical Society
• /
• v.40 no.1
• /
• pp.47-50
• /
• 2006

This 51-year-old man suffered from paraparesis of 1-week history. On preoperative images, spinal cord compression by infiltrative vertebral mass was shown at T3 and T4 level. Several months earlier, he underwent surgical resection of left 2nd to 4th ribs, due to painful growing chest wall mass, which was proved to be hepatocellular carcinoma. All available diagnostic procedure failed to uncover origin of malignancy. Operation was followed by adjuvant irradiation and chemotherapy to the vertebral mass, however he only to die in 3 months after operation. This is an extremely rare case of ectopic hepatocellular carcinoma at thoracic vertebrae which showed very aggressive clinical course. Possible pathogenic process is presented and discussed.

• Transactions of Materials Processing
• /
• v.10 no.3
• /
• pp.206-213
• /
• 2001

Dynamic deformation of metallic materials mostly accompanies substantial amounts of deformation heat. Since the flow stress of deformation is sensitive to temperature, implication of heat due to plastic work is essential to the evaluation of constitutive relations. In this study, a series of compression tests were conducted for SAF 2507 super duplex stainless steel at various temperatures and strain rates. The accumulation of plastic work was calculated through numerical integration and converted into the elevation of temperature. Subsequent logarithmic interpolation deduced isothermal flow surfaces, which were primary input data of finite element analysis. Simple closed die forging process was analyzed and optimized with commercial FEM code applying both raw and calibrated material database. The effect of accounting deformation heat was more noticeable in high-speed forming process.

• Transactions of Materials Processing
• /
• v.13 no.4
• /
• pp.334-341
• /
• 2004

In this study, a remeshing algorithm adapted to the mesh density map using the Delaunay mesh generation method is developed. In the finite element simulation of forging process, the numerical error increases as the process goes on because of discrete property of the finite elements and distortion of elements. Especially, in the region where stresses and strains are concentrated, the numerical error will be highly increased. However, it is not desirable to use a uniformly fine mesh in the whole domain. Therefore, it is necessary to reduce the analysis error by constructing locally refined mesh at the region where the error is concentrated such as at the die corner. In this paper, the point insertion algorithm is used and the mesh size is controlled by using a mesh density map constructed with a posteriori error estimation. An optimized smoothing technique is adopted to have smooth distribution of the mesh and improve the mesh element quality.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.269-272
• /
• 2006

The hydroforming processing is a relatively new technology in comparison with conventional stamping process. The hydroforming processing makes torsion beam in rear suspension of automobile. The durability of torsion beam is very important characteristic that operate in an automobile. In order to optimize the hydroforming process and satisfy the durability, the hydroforming simulation which could control an axial compression and high internal pressure with computer simulation has to be operated. This paper is about an optimum design to improve the kinematic and compliance characteristics of a torsion-beam of suspension system. The result from finite element analysis shows that the forming and the durability are optimized. If there is effect of First pressure in hydroforming processing that gap is in the die tool, the prototype of tube is not satisfied on the durability test.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2000.04a
• /
• pp.119-122
• /
• 2000

Dynamic deformation of metallic materials mostly accompanies substantial amounts of deformation heat. Since the flow stress of deformation is sensitive to temperature implication of heat due to plastic work is essential to the evaluation of constitutive relations. In this study a series of compression tests were conducted for SAF 2507 super duplex stainless steel and the accumulation of deformation heat was calculated through numerical integration method. Isothermal flow surfaces were deduced from subsequent logarithmic interpolation. Simple closed die forging process was analyzed and optimized with commercial FEM code applying both raw and calibrated material database.

• Transactions of Materials Processing
• /
• v.13 no.2
• /
• pp.129-136
• /
• 2004

Recently, instead of a matched die forming method requiring a high cost and long delivery term, a multi-point dieless forming method using a pair of matrix type punch array as flexible dies has been developed. Since the conventional multi-point dieless forming method has some disadvantages of difficulty in precise punch control and high-cost of equipment, a new concept of multi-point dieless forming method combined with an elasto-forming method has been suggested in this study. For optimal selection of elastomers, compression tests of rubbers, polyethylene and foams were carried out together with FEM analysis of the deformation behavior during sheet forming process using a rigid punch and elastomers. Compressive strain was concentrated on the upper central area of the elastomer under the punch, and the rubber exhibited higher concentration of the compressive strain than foams. Two-dimensional curved surface was formed successfully by the multi-point elasto-dieless forming method using an optimal combination of rubber and foam materials.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.5
• /
• pp.653-660
• /
• 1986

Two uppor bound solutions, by the force balance method and by a kinematically admissible velocity field, are compared for the metal forming problems in plane strain. It is concluded that these two approaches always give identical results when the geometrical configurations of the deformation model reman the same. By detailed derivations for plastic bending of a notched bar, closed die forging, compression of a rectangular block, machining with a restricted contact tool and plane strain backward extrusion, the identity of both approaches is verified.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.08a
• /
• pp.21-28
• /
• 2003

Recently, instead of a matched die forming method requiring a high cost and long deliverly ten a multi-point dieless forming method using a pair of matrix type punch array as flexible dies has been developed. As this multi-point dieless forming method has some disadvantage of difficulty in precise punch control and high-cost of equipment, a new concept of multi-point dieless forming method combined with elastomer forming was suggested in this study. For optimal selection of elastomers, compression tests of rubbers, polyethylene and foams were carried out together with FEM analysis of the deformation behavior during sheet forming process using a rigid punch and elastomers. Compressive strain was concentrated on the upper central area of the elastomer under the punch, and the rubber exhibited higher concentration of the compressive strain than foams. Two-dimensional curved surface was formed successfully by the multi-point elasto-dieless forming method using an optimal combination of a rubber and foam.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1063-1064
• /
• 2006

Mechanical properties of 7xxx series Al metal matrix composite (MMC) powders containing different amounts of ceramic were investigated. The ceramic contents of the starting powders were 5 wt.% or 10 wt.%. The powders were uniaxially cold compacted using a cylindrical die with a compacting pressure of 250 MPa and were sintered at $620^{\circ}C$ in a dry $N_2$ atmosphere for 60 min. For the heat treatment, sintered parts were solution treated at $475^{\circ}C$ and aged at $175^{\circ}C$. Compression tests were conducted to reveal the effect of $Al_2O_3$ particle content on the mechanical properties of the composites. Fractography was examined using a scanning electron microscope.

• Elastomers and Composites
• /
• v.55 no.1
• /
• pp.40-45
• /
• 2020

In this study, the mechanical and flame-retardant properties of ethylene-propylene-diene-termonomer (EPDM) based rubber compounds and various other environmentally friendly inorganic flame retardants were investigated. Alumina trihydrate (ATH) and magnesium hydroxide (MDH) were used as inorganic flame retardants. The mechanical properties after thermal oxidation aging and the flame-retardant properties of the EPDM compounds were measured using a moving die rheometer, a universal testing machine, a compression set, and a UL 94 V flammability test. We focused on how the properties were affected by the type and amount of flame retardants. The results demonstrated that the optimal mechanical and flame-retardant V-0 grade properties were obtained at an ATH content of 200 phr.