• 한국연소학회:학술대회논문집
• /
• 2013.06a
• /
• pp.33-35
• /
• 2013

The present work is an experimental investigation on potential operating range using directly injected gasoline fuel in a single-cylinder compression ignition (CI) engine. The objectives of present study were to apply auto-ignited combustion to gasoline fuel and to evaluate potential operating range. In order to auto-ignite gasoline fuel in CI engine, the fuel direct-injection system and the intake air system were modified that a flow rate and temperature of intake air were regulated. The heat-release rate (HRR), net indicated mean effective pressure (IMEP), start of combustion (SOC), and combustion duration were derived from in-cylinder pressure data in a test engine, which has 373.33cc displacement volume and 17.8 compression ratio. The exhaust emission characteristics were obtained emission gas analyzer and smoke meter on the exhaust line system.

• 한국연소학회:학술대회논문집
• /
• 2013.06a
• /
• pp.37-40
• /
• 2013

Hydrogen-dimethy ether (DME) and hydrogen-diesel compression ignition engine combustion were investigated and compared each other in a single cylinder compression ignition engine. Hydrogen and DME were used as low carbon alternative fuels to reduce green house gases and pollutant. Hydrogen was injected at the intake manifold with an injection pressure of 0.5 MPa at fixed injection timing, $-210^{\circ}CA$ aTDC. DME and diesel were injected directly into the cylinder through the common-rail injection system at injection pressure of 30 MPa. DME and diesel inejction timing was varied to find the optimum CI combustion to reduce CO, HC and NOx emissions. When DME was injected early, CO and HC emissions were high while NOx emission was low. Fuel consumption, heat release rate, and exhaust emissions were measured to analyze each combustion characteristics of each ignition promoter. Fuel consumption was decreased when diesel was used as an ignition promoter. This is due to the lower volatility of diesel which created more stratified charge than DME.

• Journal of the Korean Society of Combustion
• /
• v.15 no.4
• /
• pp.53-57
• /
• 2010

The purpose of the present work is to investigate the effect of gasoline-premixing on a combustion and emissions characteristics in a compression ignition engine. For studying combustion characteristics, a combustion pressure and rate of heat release (ROHR) were measured using a single-cylinder DI compression ignition engine with a common-rail injection system and premixed fuel injection system. In addition, exhaust emissions characteristics were studied using emission analyzers and smoke meter. The experimental results showed that the case of gasoline-premixing had longer ignition delay and lower combustion pressure compared to the cases of diesel direct injection. Furthermore, premixed gasoline-air mixture reduced NOx emissions due to low peak of ROHR.

• Journal of the Korean Society of Combustion
• /
• v.16 no.1
• /
• pp.52-57
• /
• 2011

The present study describes the characteristics of combustion and exhaust emissions in compression ignition engines using diesel-gasoline dual fuel. For investigating combustion characteristics, diesel fuel was injected directly in a single-cylinder compression ignition engine with a common-rail injection system and gasoline fuel was injected into a premixed chamber installed in an intake port. In order to investigate exhaust emission characteristics, exhaust gas was measured by emission analyzer and smoke meter. The experimental results showed that cases of diesel-gasoline dual fuel combustion exhibited extended ignition delay and reduced peak combustion pressure compared to those of directly injected diesel fuel cases. Furthermore, premixed gasoline-air mixture reduced NOx emissions due to low peak of rate of heat release(ROHR).

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.2
• /
• pp.158-165
• /
• 2008

The combustion and exhaust emissions characteristics of a liquefied petroleum gas-di-methyl ether compression ignition engine with a variable valve timing device were investigated under various liquefied petroleum gas injection timing conditions. Liquefied petroleum gas was used as the main fuel and was injected directly into the combustion chamber. Di-methyl ether was used as an ignition promoter and was injected into the intake port. Different liquefied petroleum gas injection timings were tested to verify the effects of the mixture homogeneity on the combustion and exhaust emission characteristics of the liquefied petroleum gas-di-methyl ether compression ignition engine. The average charge temperature was calculated to analyze the emission formation. The ringing intensity was used for analysis of knock characteristics. The combustion and exhaust emission characteristics differed significantly depending on the liquefied petroleum gas injection and intake valve open timings. The CO emission increased as the intake valve open and liquefied petroleum gas injection timings were retarded. However, the particulate matter emission decreased and the nitrogen oxide emission increased as the intake valve open timing was retarded in the diffusion combustion regime. Finally, the combustion efficiency decreased as the intake valve open and liquefied petroleum gas injection timings were retarded.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.6
• /
• pp.105-113
• /
• 2010

In this study, a feasibility test of liquid petroleum gas (LPG) compression ignition (CI) engine has been carried out to study the effectiveness of cetane enhancing additive: Di-tertiary-butyl peroxide (DTBP). Performance and emissions characteristics of a CI engine fuelled with DTBP blended LPG fuel were examined. Also, the effect of EGR (exhaust gas recirculation) on the combustion and emissions characteristics has been investigated. Results showed that stable engine operation over a wide range of the engine loads was possible. Exhaust emissions measurements showed that hydrocarbon were decreased with the blended fuel at enhancing cetane number. Furthermore, the combustion stability of LPG with a cetane number improver was equivalent to that of commercial Diesel fuel. Increasing the EGR rate leads to deteriorate the IMEP (indicated mean effective pressure) and increase the ignition delay. It was found that the exhaust emissions with the EGR resulted in a very large reduction in nitrogen oxides at the expense of higher THC and CO emissions. Considering the results of engine performance and exhaust emissions, LPG blended fuel of enhancing cetane number could be used as an alternative fuel for diesel in a CI engine.

• Journal of the Korean Society of Industry Convergence
• /
• v.19 no.1
• /
• pp.31-38
• /
• 2016

Since the oil shock of 1970's there was a strong upward tendency for the use of the high viscosity and poorer quality fuels. Therefore the misfiring engine occurs due to the decrease of quantity injected for lean burn and emission control in Compression Ignition Common Rail Direct Injection diesel engine. In this study, it is designed and used the test bed which is installed with fuel injector controller. In addition to equipped engine using CRDI by controlling the injection timing with mapping modulator, it has tested and analyzed the engine performance and combustion characteristics, as it is varied that they are the operating parameters: fuel injected quantity, engine speed and injection timing.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.5
• /
• pp.53-60
• /
• 2009

In this study, LPG-blended DME fuel was experimentally investigated in CI(compression ignition) engine. In particular, performance, emissions characteristics (including hydrocarbon, CO, and NOx emissions), and combustion stability of engine fueled with LPG-blended DME fuel were examined. The extent of LPG fuel in the blended fuel was 0-40 wt%. Results showed that stable engine operation was possible in a wide range of engine loads on DME blended with maximum 30% of LPG by mass in a CI engine. Considering the results of the engine power output and exhaust emissions, blended fuel up to 30% of LPG by mass can be used as an alternative to diesel in a CI engine. LPG blended DME fuel is expected to have potential for enlarging the DME market.

• Journal of ILASS-Korea
• /
• v.14 no.4
• /
• pp.153-162
• /
• 2009

The use of inedible vegetable oils as substitute for diesel fuel in compression ignition engine is of significance because of the great need for edible oil as food, and the reduction of biodiesel production cost etc. Jatropha curcas oil which is a leading candidate for the commercialization of inedible vegetable oils is selected in this study for reviewing the application in CI engine as an alternative fuel. The important properties of jatropha oil (JO) and JO biodiesel are summarized from the various sources in the literature. It is found that five different types of alternative fuel from JO such as neat JO, JO blends with diesel or other fuel, neat JO biodiesel, JO biodiesel blends with diesel or other fuel and degummed JO were extensively examined in the diesel engine. Two different application types of alternative fuels from JO such as preheating and dual fuelling were also tested, It should be pointed out that most of these applications are limited to single cylinder conditions. The systematic study for the selection of effective application method is required. It is clear that the blends of JOME and diesel can replace diesel fuel up to 10% by volume for running the existing common rail direct injection systems without any durability problems. The systematic assessment of spray characteristics of different types of JO and its derivatives for use as diesel engine fuel is also required.

• Journal of ILASS-Korea
• /
• v.24 no.1
• /
• pp.35-42
• /
• 2019

Syngas is widely produced by incomplete combustion of coal, water vapor, and air (oxygen) in a high-temperature/high-pressure gasifier through a coal-gasification process for power generation. In this study, a simulation syngas which was mainly composed of $H_2$, CO, $CO_2$, and $N_2$ was fueled with diesel. A modified single cylinder compression ignition (CI) engine is equipped with intake port syngas supply system and mechanical diesel direct injection system for dual fuel combustion. Combustion and emission characteristics of the engine were investigated by applying various syngas composition ratios and compression ratios. Diesel fuel injection timing was optimized to increase indicated thermal efficiency (ITE) at the engine speed 1,800 rpm and part load net indicated mean effective pressure ($IMEP_{net}$) 2 to 5 bar. ITE of the engine increased with the $H_2$ concentration, compression ratio and engine load. With 45% of $H_2$ concentration, compression ratio 17.1 and $IMEP_{net}$ 5 bar, ITE of 41.5% was achieved, which is equivalent to that of only diesel fuel operation.