• The Journal of Korean Obstetrics and Gynecology
• /
• v.25 no.2
• /
• pp.108-119
• /
• 2012

Objectives: This study was performed to compare the differences between decoctions extracted by different extraction method and extraction time. Methods: Decoctions were prepared with pressurized or non-pressurized extraction for 60, 120 and 180min. The yield of extract, total soluble solid content, hydrogen ion concentration(pH) and the content of reference compound in Sipjeondaebo-tang (Siquandabu-tang) were investigated. Results: While yields and the total soluble solid of decoction were higher in pressurized method proportional to extraction time, pH values were lower in pressurized method and showed decreasing values with increasing extraction time. Albilflorin, ferulic acid, nodakenin, coumarin, cinnamaldehyde and glycyrrhizin were contained in decoctions by pressurized extraction method more than non-pressurized method whereas the content of coumarin was higher in decoctions by non-pressurized extraction method. In addition, coumarin was extracted increasingly with extraction time in decoctions by pressurized method, however, nine compounds except cinnamaldehyde showed the tendency of increasing proportional to extraction time. Conclusions: The results show that extraction methods including pressurized or non-pressurized extraction, and extraction time could affect the physicochemical characteristic or composition of Sipjeondaebo-tang(Siquandabu-tang) decoction.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.38 no.4
• /
• pp.35-44
• /
• 2010

This study will define the features of the viewpoint that best enables the view of Busan Port from Young-Do. Special focus will be on spatial distribution, the type Busan Port sights that can be experienced from Young-Do, the compositional characteristic of a port landscape and visual characteristic. The results are based on 27 selected viewpoints and are as follows. Firstly, the patterns of the spatial distribution of viewpoints are classified as park, public facility and wayside types. It was found that most viewpoints are located along a wayside. Secondly, the types of Busan Port sights that can be experienced from Young-Do are divided into three kinds: surrounding stand-line type, facing the port and the type of penetrating city. The major type was of penetrating city among the three patterns. The reason for this is that the point of view for Busan Port was changed into a prospect over the sea since city and road sections have been expanding due to the urbanization of Young-Do. Thirdly, the compositional characteristics of the port landscape are divided into three styles: panoramic, corridor, and rooftop. The most frequent type is the rooftop style among the three characteristics. This fact indicates that the picture of Busan Port seen from Young-Do loses continuity of view and that housetops inhibit the sense of distance. Lastly, the visual characteristics of the viewpoint were analyzed. The angles of the declination of the viewpoints are concentrated on the horizontally closed parts. Thirteen points lie between $-3^{\circ}$ and $-1^{\circ}$, and twelve points between $-6^{\circ}$ and $-4^{\circ}$. The visual axes of the depression are two points because sight is interrupted by buildings which are built when the city expands. Two viewpoints for experiencing the optimum landscape of depression should be prepared to ensure continuous preservation of the viewpoints. The sight creates a wide prospect, reaching from 0.2km to 6.4km. It is expected that the results of this study can be used for the landscape plans of port cities including the management and preservation of viewpoints.

• Journal of Conservation Science
• /
• v.20
• /
• pp.105-117
• /
• 2007

This study is examined the beads excavated in the Sacheon Neukdo ruins to investigate the features of archaeological chemistry and to compare those of the same type of beads excavated within the Gyeongsang-do area by means of scientific analysis. The samples have been observed the micro-structures by an optical microscope and SEM and confirmed the physical property by density measurement. Chemical property have been analyzed main components such as flux, stabilizers, and colorants by SEM-EDS. Besides, XRD was used to identified the characteristic materials of beads. The white opaque beads, which was initially estimated as sea-shell beads, confirm as amorphous silica material. The glass beads, which are blue type as a result of compositional analysis, it is revealed potash glass group and LCA(Low-CaO, $Al_2O_3$) system. gB ones are revealed only in LCA-A(LCA-CaO<$Al_2O_3$), while purple blue ones in LCA-B(LCA-CaO>$Al_2O_3$).

• Journal of the Mineralogical Society of Korea
• /
• v.10 no.2
• /
• pp.105-113
• /
• 1997

Mineral description and mineralogical characterization were made for the wellsite, a barrian zeolite, which found as diagenetic alterations in the Miocene pyroclastic rocks in Gampo area. The wellsite occurs together with clinoptilolite, smectite and apatite as euhedral crystallites (0.2~0.4mm) forming interpenetraion twinning in the vesicles of altered pmice fragments. Compared to other reported wellsites, the wellsite is rather silicic (Si/(Al+Fe): 3.12-3.16) and Ca-rich. Unit cell dimensions and chemical formular determined from XRD, EMPA and TGA data are as follows:a=9.883$\AA$, b=14.204$\AA$, c=8.677$\AA$, $\beta$-124.764$^{\circ}$, (Ba0.57K0.36)(Ca1.18Na0.04)Al3.9Si12.1O32.13.9H2O.The cation composition of the Gampo wellsite, which shows an exchange reaction in the form of Ba2++Ca2+=2(K++Na-), is deviated far from the compositional range of a phillipsite-harmotome series. Due to higher abundance of divalent cations (Ca, Ba) and si in the wellsite, cimpared to those of the phillipsite and harmotome reported in other areas, the zeolite seems to be characteristic of higher water content (18.7 wt%) and higher thermal stability. XRD, chemical and thermo-chemical results of the wellsite reflects that wellsite is rather a Ba- and Ca-rich end member of a phillipsite-harmotome-wellsite series than an intermediate phase of phillipsite-harmotome series or a barrian variety of phillipste.

• Microbiology and Biotechnology Letters
• /
• v.27 no.1
• /
• pp.41-45
• /
• 1999

A tentative composition and some properties of biosurfactants, type I and type II, from Pseudomonas sp. SW1 are described. Biosurfactant type I and II are soluble in water, dichloromethane, chloroform, and a mixture of chloroform and methanol, respectively. The UV absorption spectrum of biosurfactants showed three characteristic peaks in the range of 212, 250 and 365nm, respectively. As a result of IR spectroscopy, GC/MS analysis and biochemical analysis, biosurfactant type I was a polymeric biosurfactant containing carbohydrate, lipid and protein. The carbohydrate was characterized as rhamnose. The lipid part consists of $C_{14}-C_{23}$ fatty acid when analyzed by GC/MS. The biosurfactant type II was a rhamnolipid consisting of carbohydrate and lipid.

• Journal of the Korean institute of surface engineering
• /
• v.44 no.5
• /
• pp.185-189
• /
• 2011

$Cu_2ZnSnSe_4$ thin films for solar absorber application were prepared by pulsed laser deposition of a synthesized $Cu_2ZnSnSe_4$ compound target. The film's composition revealed that the deposited films possess an identical composition with the target material. Further film compositional control toward a stoichiometric composition was performed by optimizing substrate temperature, deposition time and target rotational speed. At the optimum condition, X-ray diffraction patterns of films showed that the films demonstrated polycrystalline stannite single phase with a high degree of (112) preferred orientation. The absorption coefficient of $Cu_2ZnSnSe_4$ thin films were above 104 cm.1 with a band gap of 1.45 eV. At an optimum condition, films were identified as a p type semiconductor characteristic with a resistivity as low as $10^{-1}{\Omega}cm$ and a carrier concentration in the order of $10^{17}cm^{-3}$.

• Journal of the Korean Society of Costume
• /
• v.60 no.9
• /
• pp.16-25
• /
• 2010

This study reinterpreted the formative design elements of traditional grate patterns to create new lattice patterns and come up with a design concept for fashion-cultural products that highlight the uniqueness of traditional Korean culture and its characteristic features. Methodologically, the computer design software programs Adobe Illustrator CS2 and Adobe Photoshop were used to make grate patterns motifs. and they were applied to scarves and again to blouses using a three-dimensional simulation technique. In this study, three basic motifs for a new formative image were set using graphical functions such as omitting, simplifying, overlapping, repeating and reducing shapes based on the images of traditional 亞-shaped, arched and floral lattices, and each motif was expanded to have two variations with different colors applied to them. The direction of basic motif design was set to fit for each of fashion-cultural items such as scarves and blouses. Basic colors for motifs were arranged to create a colorful and modern but staid image in pink, blue, purple, green, yellow and brown tones. Based on a developed motif, changes were made in blouse design with lattice patterns through a variety of effects such as repetition, rotation, cross-arrangement, and oblique arrangement, and three-dimensional simulation was used to bring the design to life. Scarf design employed and applied the existing motifs in an appropriate manner for design purposes and reconstructed them through such effects as repetition, rotation, compositional variation and gradation to express a gorgeous and refined image.

• Journal of the Korean Magnetics Society
• /
• v.2 no.3
• /
• pp.251-256
• /
• 1992

Artificial superlattices of Co/Pd were prepared by RF magnetron sputtering Multilayered structure and compositional modulation were analyzed with a side angle x-ray diffractometer. It has been found that expansion of Co lattice occured in this artificial superlattice due to the lattice mismatch between Co and Pd. Perpendicular magnetic anisotropy could be observed when the Co layer thickness became less than 8${\AA}$ and maximum coercivity of 2350 Oe could be obtained in [Co(2.5 ${\AA}$)/Pd(9.3 ${\AA})]_{50}$/Pd$(200\;{\AA})$ with a perfect squareness of magnetic hysteresis loop. Characteristic of perpendicular magnetic anisotropy in Co/Pd superlattices could be related to the expansion of Co lattice caused by Pd layer and it turned out that as the thickness of Pd layer increased, perpendicular magnetic anisotropy increased. The interface anisotropy energy and volume anisotropy energy were calculated to be 0.29 ergs/$cm^2$ and -$6.9{\times}10^6$ ergs/$cm^3$ respectively, which are consistent with the values reported elsewhere.

• Proceedings of the Korean Society of Near Infrared Spectroscopy Conference
• /
• 2001.06a
• /
• pp.1125-1125
• /
• 2001

Micro-scale test methods are producing small-sample size where the conventional physical and chemical tests can not be used (high standard deviation, uncertain sampling conditions, low repeatability). Different small-scale test methods were developed recently for determination of physico-chemical, functional, rheological properties of wheat or wheat dough using miniaturized instruments with sophisticated sample preparation/handling and mechanics (RVA, 2 g mixograph, micro-Z-arm mixer, small-scale noodle maker, micro-baking method etc.). The small-scale methodologies can be used as basic research tools or as technology supported measurements and can be also essential in the early selection for quality traits in breeding programs. The milling as a sample preparation step is essential procedure providing good quality flour or semolina samples from small amount of grain (5-10 g) in a reproducible and reliable way. The aim of present study was to use NIR as quality control tool, and to evaluate the recently developed and manufactured micro-scale lab mill (FQC-2000) produced by Inter-Labor Co. Ltd., Hungary. The milling characteristics of the new instrument were compared to other laboratory mills and the effects of milling action on the chemical composition of fractions were analysed. The fractions were tested with both chemical and near infrared spectroscopic methods. The micro-scale milling resulted significantly different yields, particle size distributions and different fractions from compositional point of view. The near infrared spectra were sensitive enough to distinguish the fractions obtained by different milling procedures. Quantitative NIR calibration equations were developed and tested in order to measure the chemical composition of characteristic milling fractions. Special qualification procedure the PQS (Polar Qualification System) method was used for detecting the differences between fractions obtained by macro and micro-milling procedures. The results and the limitations of PQS method in this application will be discussed.

• Journal of the Korean Society for Heat Treatment
• /
• v.19 no.1
• /
• pp.30-36
• /
• 2006

Fretting fatigue behavior of SCM420 steel commonly used in the automotive industry for structural applications was investigated in this study. In addition, the effect of bridge pad on the fretting fatigue test was evaluated from different pad materials and following conclusions were drawn. Simple fatigue limit of SCM 420 steel was determined to be 350 MPa while this value was 225 MPa and 285.5 MPa with SCM420H and with SM45C pad, respectively. Reduction in fatigue limit was, thus found to be 35.7% and 17.9% with SCM 420H pad and SM45C pad, respectively. Results of fracture surface observation revealed that typical striation pattern of fatigue failure existed as well as dimpled and cleavage frature appearance was found in final fractured region. From the EDS compositional analysis, test sample and pad part all had high signals for oxygen and iron, suggesting that worn particles might be iron oxide, although exact chemical composition has to be confirmed. Considerable reduction in fatigue life was apparent in SCM 420 steel under fretting fatigue against simple fatigue. Such reduced fatigue life by fretting damage should be considered as an important factor not only in the viewpoint of repairing but also inevitably in the design stage of structural components.