• Elastomers and Composites
• /
• v.41 no.2
• /
• pp.79-87
• /
• 2006

This study are conducted for the purpose of developing rubber material with noise and crack resistance. Cure characteristics, physical properties, thermal resistance, fuel resistance, abrasion resistance, crack resistance and noise resistance of NBR compounds with the various amounts of oleamide and aramid chip were investigated. From the measurements of cure characteristics and Mooney viscosities, cure characteristics of uncured rubber showed that a torque was decreased as the amount of oleamide increased. Hardness, modulus and elongation of rubber specimens tended to be reduced gradually, however, tensile strength remained unchanged as the amount of the oleamide increased. As a testing results of heat resistance for 70 hours at $120^{\circ}C$ and oil resistance far 70 hours at $40^{\circ}C$, tensile strength and elongation were all reduced. From the TGA/DSC analysis, there was no such a change observed in thermal characteristics of rubber materials. As a result of testing basic physical properties, abrasion resistance, noise resistance and crack resistance, the optimum ratio of oleamide to NBR was found to be 3 phr, while that of aramid to NBR 227001 was 1 phr.

• Elastomers and Composites
• /
• v.39 no.1
• /
• pp.61-70
• /
• 2004

This work is about the development or asphalt sealant using the waste edible oil. Asphalt sealant has been used for crack filler and bridge deck joint sealer Several plasticizers such as aromatic or paraffin process oils, DOP, Bunker C fuel oil, and waste edible oil were compounded with the basic components such as asphalt(AP-5), a thermoplastic elastomer(SBS triblock copolymer), a tackifying agent(petroleum resin), and stabilizers. Penetration, softening point, ductility, and elongation by tensile adhesion of those asphalt sealant compounds were measured. Their properties were changed largely depending on both the type and content of plasticizers. Waste edible oil and DOP were the best plasticizers for the low temperature tensile adhesion characteristics. Penetration and elongation by tensile adhesion of asphalt sealant compounds increased with the increase of waste edible oil content and decreased with the increase of talc content. The manufacture of asphalt sealant with low penetration and excellent low temperature tensile adhesion was possible by the recipe optimization.

• Elastomers and Composites
• /
• v.47 no.2
• /
• pp.141-147
• /
• 2012

Silicone resin has no water-absorbing function because it is a strong hydrophobic polymer. However, addition of super absorbent polymer gives much better absorbency than that of conventional silicone resin. In this study, we developed novel silicone materials with water-absorbing function by choosing three types of amorphous acrylic super absorbent polymers with different particle sizes, determining the mixing ratio of the three polymers and applying the mixtures into two-component type silicone material for medical purpose. The change in the mechanical properties such as tensile strength, tear strength, compressive strength and hardness was investigated by varying the particle size and content ratio of the added super absorbent polymers while preparing the silicone resins. The absorbency of the silicone resins was measured over time. Additionally, the particle shape of the super absorbent polymers as well as the distribution within the silicone resin was observed using an optical microscope.

• Elastomers and Composites
• /
• v.44 no.3
• /
• pp.299-307
• /
• 2009

The effects of reinforcing materials on durability and mechanical properties of V-rib belt were investigated. Cotton fiber and ZnO were used as a filler for CR, and cotton and aramid fiber were used for EPDM rubber compounds. These materials were prepared as a specimen and V-rib belt for heat resistant and mechanical test. High contents of ZnO give improved wear resistance, and higher contents of cotton fiber showed higher durability in high rotation speed but lower wear resistance for CR rubber compounds. Using the aramid and cotton fiber together in EPDM rubber compounds, thermal and wear resistance were improved simultaneously. The material containing EPDM matrix showed better durability and wear resistance than those of containing CR matrix comparing in the same cotton fiber contents.

• Elastomers and Composites
• /
• v.44 no.3
• /
• pp.269-273
• /
• 2009

A study on the life-time expectation of a CR-modified NR rubber composite through the change of thermal degradation characteristics was performed using both isothermal thermogravimetric analysis (TGA) and thermomechanical analysis (TMA). Master curves at reference temperature of $90^{\circ}C$ could be obtained with shift factor $a_T$, which was determined empirically using Time-Temperature Superposition Principle (TTSP). Activation energies could be calculated from the slope of Arrhenius plot of shift factor and showed similar values of $E_{a,TGA}$= 41.2 and $E_{a,TMA}$= 54.5 kJ/mol, respectively. It was considered from the results that chemical degradation resulting weight loss of the sample might be closely related to a physical degradation such as the dimensional change of the sample.

• Elastomers and Composites
• /
• v.45 no.3
• /
• pp.212-216
• /
• 2010

The materials of the lithium ion battery gasket require chemical resistance to the electrolyte, electrical insulating, compression set, anti-contamination and heat resistance. To estimate suitability for rubber which has better performance to compression set than PFA, each compound were made with various rubbers, such as EPDM, NBR, FKM, FVMQ, VMQ and we checked the characteristics of each compound. Samples from each compound was deposited in Propylene Carbonate and tested for changing of Hardness and Volume during 1,000 hr with $80^{\circ}C$. EPDM and VMQ showed good performance to chemical resistance to the electrolyte, and also we could get the values over $10^{10}{\Omega}cm$ on volume resistance basis in electrical insulating. EPDM and VMQ were judged as the most suitable material.

• Elastomers and Composites
• /
• v.42 no.3
• /
• pp.159-167
• /
• 2007

Hydraulic actuators are used widely for industrial machinery. The seal made from elastomer is used as a core part of the actuator, NBR(nitrile butadiene rubber) materials with high quality of oil resistance and abrasion resistance is used widely, requiring excellent characteristic of sealing. According to applied circumstances, the actuators for industrial machinery are used under different temperature situations. In this study, three different kinds of NBR, which is Hs70, 80, 90 are determined as one of hydraulic materials. An experimental investigation is performed to confirm the non-linearity under different temperature ($-10^{\circ}C,\;20^{\circ}C,\;80^{\circ}C,\;100^{\circ}C$) situation, material constants for finite element analysis and plastic deformation in accordance with Load-unload.

• Elastomers and Composites
• /
• v.48 no.1
• /
• pp.24-29
• /
• 2013

We have developed the synthetic processes for the monomers of polyamide-type TPEs (thermoplastic elastomers, TPAEs) obtained from vegetable oil. TPAEs have several superior physical properties to those of thermoplastic elastomers (TPEs). From the common starting material, oleic acid, which is commonly found in various vegetable oils, we have synthesized three ${\omega}$-amino acid monomers ($C_9$, $C_{10}$ and $C_{11}$ ${\omega}$-amino acid) and three ${\alpha}$, ${\omega}$-dicarboxylic acids($C_9$, $C_{10}$ and $C_{11}$ ${\alpha}$, ${\omega}$-dicarboxylic acid) for TPAEs in good yields.

• Structural Engineering and Mechanics
• /
• v.12 no.6
• /
• pp.657-668
• /
• 2001

Fiber reinforced cementitious composites are nowadays widely applied in civil engineering. The postcracking performance of this material depends on the interaction between a steel fiber, which is obliquely across a crack, and its surrounding matrix. While the partly debonded steel fiber is subjected to pulling out from the matrix and simultaneously subjected to transverse force, it may be modelled as a Bernoulli-Euler beam partly supported on an elastic foundation with non-linearly varying modulus. The fiber bridging the crack may be cut into two parts to simplify the problem (Leung and Li 1992). To obtain the transverse displacement at the cut end of the fiber (Fig. 1), it is convenient to directly solve the corresponding differential equation. At the first glance, it is a classical beam on foundation problem. However, the differential equation is not analytically solvable due to the non-linear distribution of the foundation stiffness. Moreover, since the second order deformation effect is included, the boundary conditions become complex and hence conventional numerical tools such as the spline or difference methods may not be sufficient. In this study, moment equilibrium is the basis for formulation of the fundamental differential equation for the beam (Timoshenko 1956). For the cantilever part of the beam, direct integration is performed. For the non-linearly supported part, a transformation is carried out to reduce the higher order differential equation into one order simultaneous equations. The Runge-Kutta technique is employed for the solution within the boundary domain. Finally, multi-dimensional optimization approaches are carefully tested and applied to find the boundary values that are of interest. The numerical solution procedure is demonstrated to be stable and convergent.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.56.1-56.1
• /
• 2009

The intermediate operating temperature of solid oxide fuel cells (IT-SOFCs) have achieved considerable importance in the area of power fabrication. This is because to improve materials compatibility, their long-term stability and cost saving potential. However, to conserve rational cell performance at reduced-temperature regime, cathode performance should be obtained without negotiating the internal resistance and the electrode kinetics of the cell. Recently, double perovskite structure cathodes have been studied with great attention as a potential material for IT-SOFCs. In this study, double-perovskite structured cathodes of $GdBaCoCuO_{5+\delta}$, $GdBaCo_{2/3}Cu_{2/3}Fe_{2/3}O_{5+\delta}$ compositions and $(1-x)GdBaCo_2O_{5+\delta}+xCe_{0.9}Gd_{0.1}O_{1.95}$ (x = 10, 20, 30 and 40 wt.%) composites were evaluated as the cathode for intermediate temperature solid oxide fuel cells(IT-SOFCs). Electrical conductivity of the cathodes were measured by DC 4-probe method, and the thermal expansion coefficient of each sample was measured up to $900^{\circ}C$ by a dilatometer study. Area specific resistances(ASR) of the $GdBaCo_{2/3}Cu_{2/3}Fe_{2/3}O_{5+\delta}$ cathode and 70 wt.% $GdBaCo_2O5+\delta$ + 30wt.% Ce0.9Gd0.1O1.95 composite cathode on CGO electrolyte substrate were analyzed using AC 3-probe impedance study. The obtained results demonstrate that double perovskite-based compositions are promising cathode materials for IT-SOFCs.