• 공업화학
• /
• 제24권4호
• /
• pp.357-362
• /
• 2013

High efficiency particulate air (HEPA) 필터를 시험하기 위하여 단분산 polystyrene latex spheres (PLS) 및 PS-MPS/실리카복합 나노구체가 이용되었다. 사용된 모든 나노구체들은 필터시험 전에 평균입경과 변동계수 값을 측정하여 시험용 인조먼지로서 적정함을 평가하였다. PLS 및 복합 나노구체의 입경은 유화중합 중 반응온도와 안정제의 양을 조절하여 100~300 nm 범위에서 잘 조절되었으며, 변동계수의 경우도 단분산 입자분포로 판단되는 15%보다 낮은 3~7% 범위이었다. 한편 HEPA 필터시험 결과는 사용된 모든 나노구체들이 공기필터의 시험을 위한 시험용 인조먼지로서 아주 적절함을 보여주었다.

• Restorative Dentistry and Endodontics
• /
• 제27권4호
• /
• pp.403-410
• /
• 2002

Several ways of curing are being tried to improve material's properties and reduce marginal gap. However, all are considering about the pattern of light intensity. It was noted from the preliminary study the change of light wavelength from filter changing may give an impact on material's property and microleakage. The object of this study was to verify the effect of filters with various wavelength width on the microhardness and microleakage of composite resin ; hybrid type of DenFil and submicron hybrid type of Esthet X. Composite resins were cured using 3 kinds of filter; narrow-banded(465-475 nm), mid-banded(430-470 nm), wide-banded(400-500 nm). After the estimation of microhardness. degree of dye penetration and the maximum gap from SEM evaluation were done between 4 groups that showed no difference in microhardness value of the lower surface . The results were as follows : 1 Adequate microhardness could not be gained with a narrow-banded filter irrespective of curing time. At the upper surface, DenFil should be polymerized with middle or wide-banded filter for 20 seconds at least, while Esthet X be col$.$ed with middle or wide-banded filter for 30 seconds at least to get simitar hardness value to control group. 2. There was little dye penetration in enamel margin, but all dentin margins skewed much more dye penetration irrespective of curing conditions. Although there was no statistical difference, groups cured with mid-banded filter for 40 seconds and with wide-width filter for 20 seconds showed relatively less dye penetration. 3. It was revealed from the SEM examination that group cured with wide-banded filter had the smallest gap without statistical significance. Spearman's rho test showed that the correlation between the results of dye penetration and SEM examination was very low. From these results, it could be concluded that curing with wide-width filter would be better than the other techniques, even though the curing technique using mid-width filter seems to have its own unique advantage.

• 한국정보통신학회논문지
• /
• 제17권10호
• /
• pp.2233-2238
• /
• 2013

본 논문에서는 복합 좌/우향 (CRLH) 전송 선로를 이용하여 초광대역 필터의 새로운 설계 방법에 대해 나타내었다. CRLH 전송선로의 특성을 구현하기 위해 접지면에는 결함 접지면 구조(DGS)와 윗면에는 마이크로스트립 인터디지털 결합기를 이용하였다. 본 논문에서 제안하는 CRLH 전송선로는 저역통과 필터와 고역통과 필터의 특성을 결합한 특성을 나타내며 삽입손실이 적고 광대역 필터 특성을 얻을 수 있는 장점이 있다. 몇 개의 셀 구조에 대해 연구하였으며, 본 논문에서는 3-셀 구조의 UWB 필터를 설계하고 구현하였다. 실험결과와 시뮬레이션 결과가 일치하며 중심주파수 5 GHz에서 105 %의 대역폭을 나타내며 삽입손실은 중심주파수에서 0.7 dB를 나타내었다.

• 한국항행학회논문지
• /
• 제16권2호
• /
• pp.227-233
• /
• 2012

본 논문은 LTCC를 이용하여 구현된 GPS와 WLAN용 대역통과 필터 설계방법을 제안한 것이다. 여기서 구현한 여파기는 버터워스 저역통과 여파기와 CRLH(Composite Right/Left-Handed) 전송선로의 고역통과 특성을 결합한 대역 통과 여파기를 설계하였다. 이렇게 설계된 여파기는 유전율 7.2의 그린쉬트를 이용한 LTCC 공정을 사용하여 1.5 GHz의 GPS와 2.4 GHz의 WLAN 대역의 대역통과 여파기를 제작하였다. 제작된 여파기의 삽입손실 결과는 1.5 GHz GPS대역에서 1.66 dB 또, 2.4 GHz WLAN 대역에서는 3.20 dB를 만족하는 대역통과 특성을 얻었다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 춘계 학술발표대회 개요집
• /
• pp.39-41
• /
• 2004

This study is to optimize the condition of pulse parameters using the response surface method in micro pulse TIG welding of pleated type metallic filter. The input parameters used were pulse current, base current, pulse duty, frequency and welding speed and the hydraulic pressure was used as the output parameter. The central composite design was designed using second order regression model, As the results, the optimal welding condition to manufacture the pleated type metallic filter was obtained.

• Composites Research
• /
• 제27권4호
• /
• pp.152-157
• /
• 2014

Non-destructive testing methods of composite materials are very important for improving material reliability and safety. AE measurement is based on the detection of microscopic surface movements from stress waves in a material during the fracture process. The examination of AE is a useful tool for the sensitive detection and location of active damage in polymer and composite materials. FBG (Fiber Bragg Grating) sensors have attracted much interest owing to the important advantages of optical fiber sensing. Compared to conventional electronic sensors, fiber-optical sensors are known for their high resolution and high accuracy. Furthermore, they offer important advantages such as immunity to electromagnetic interference, and electrically passive operation. In this paper, the crack detection capability of AE (Acoustic Emission) measurement was compared with that of an FBG sensor under tensile testing and buckling test of composite materials. The AE signals of the PVDF sensor were measured and an AE signal analyzer, which had a low pass filter and a resonance filter, was designed and fabricated. Also, the wavelength variation of the FBG sensor was measured and its strain was calculated. Calculated strains were compared with those determined by finite element analysis.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2000년도 추계종합학술대회 논문집(2)
• /
• pp.257-260
• /
• 2000

In this paper, a Gm-C filter for low voltage and low power applications using a fully-differential transconductor is presented. The designed transconductor using the series composite transistors and the low voltage composite transistors has wide input range at low supply voltage. A negative resistor load (NRL) technology for high DC gain of the transconductor is employed with a common mode feedback (CMFB). As a design example, the third-order Elliptic lowpass filter is designed. The designed filter is simulated and examined by HSPICE using 0.25${\mu}{\textrm}{m}$ CMOS n-well parameters. The simulation results show 105MHz cutoff frequency and 2.4㎽ power dissipation with a 2.5V supply voltage.

• 한국대기환경학회지
• /
• 제20권3호
• /
• pp.361-369
• /
• 2004

A metal fiber bed has seldom been applied to the practical filtration process despite its excellent mechanical and chemical stability. The filter-bed used in this work was highly porous with open structure, of which apparent porosity was 80 ∼ 90%. Although pressure loss across the filter-bed was very low, separation efficiency was found to be quite high. This paper focuses on the basic filtration mechanisms of a metal filter-bed and a thin ceramic filter from fly ash for reference. The experimental parameters were face velocity, dust loading and porosity of filter-bed. Pressure drop increased with increasing face velocity and dust feeding load for both filters. It also showed that dust particles deposited in the deep flow path, finally resulting in clogging the pore channels. It thereby indicates that the dominating mechanism of the metal filter-bed would be depth filtration. Meanwhile, the thin fly ash composite filters trapped the aerated dust mainly on the surface of the filter medium, so that the instantaneously formed dust layer might cause a steep increase of pressure drop across the filtration system.

• Journal of electromagnetic engineering and science
• /
• 제13권4호
• /
• pp.245-250
• /
• 2013

This paper presents a tunable bandpass filter based on the varactor-loaded composite right- and left-handed transmission line (CRLH-TL). The proposed filter is composed of one CRLH-TL unit cell, which corresponds to the third-order bandpass filter. The tunable bandpass filter is designed using only lumped-elements. The use of lumped elements saves space and lowers the fabrication cost. The size of the proposed tunable bandpass filter is $17mm{\times}5mm$, neglecting the feed lines and DC lines. All of the varactors are controlled by one DC bias. The center frequency of the bandpass filter can be controlled by varying the value of the varactors. The tunable range of the center frequency is from 412.5 to 670 MHz. The insertion loss is less than 3 dB, the return loss is more than 10 dB in the passband.

• 한국항행학회논문지
• /
• 제17권2호
• /
• pp.196-201
• /
• 2013

본 논문은 대칭 구조의 CRLH 전송선로를 바탕으로 이중모드에서 동작하는 평형 필터 설계를 제안한 것이다. 기존의 대칭 구조와는 다르게 이 구조에서는 공통 모드와 차동 모드의 이중모드에서 동작한다. 이러한 성질은 이 구조의 대칭면에 단락회로를 그라운드 비아에 의해서 동작되도록 구현하였다. 이렇게 하면 공통 모드와 차동 모드에서 모두 동작하는 특성을 얻을 수 있으며, 이러한 성질을 이용하여 평형 필터를 구현하였다. 이러한 특징들을 확인하기 위하여 5개의 대칭 CRLH 단위 셀로 시뮬레이션, 제작 및 측정을 하여 공통 모드와 차동 모드에서 동일하게 동작하는 평형 필터의 특성을 얻었다.