• 제목/요약/키워드: Composite Residual Stress

검색결과 234건 처리시간 0.026초

Measurement and assessment of imperfections in plasma cut-welded H-shaped steel columns

  • Arasaratnam, P.;Sivakumaran, K.S.;Rasmussen, Kim J.R.
    • Steel and Composite Structures
    • /
    • 제6권6호
    • /
    • pp.531-555
    • /
    • 2006
  • H-shaped welded steel column members are fabricated by welding together pre-cut flanges and the web. Modern fabricators are increasingly using plasma-cutting technique instead of traditional flame cutting. Different fabrication techniques result in different degrees of geometric imperfections and residual stresses, which can have considerable influence on the strength of steel columns. This paper presents the experimental investigation based temperature profiles, geometric imperfections, and built-in residual stresses in plasma cut-welded H-shaped steel column members and in similar flame cut-welded H-shaped steel columns. Temperature measurements were taken during and immediately after the cutting operations and the welding operations. The geometric imperfections were established at closely spaced grid locations on the original plates, after cutting plates into plate strips, and after welding plate strips into columns. Geometric imperfections associated with plasma cut element and members were found to be less than those of the corresponding elements and members made by flame cutting. The "Method of Section" technique was used to establish the residual stresses in the plate, plate strip, and in the welded columns. Higher residual stress values were observed in flame cut-welded columns. Models for idealized residual stress distributions for plasma cut and flame cut welded sections have been proposed.

Electro-Micromechanical 시험법을 이용한 탄소 섬유 강화 에폭시아크릴레이트 복합재료의 자외선과 열경화에 따른 경화 모니터링 및 비파괴적 계면 평가 (Nondestructive Interfacial Evaluation and Cure Monitoring of Carbon Fiber/Epoxyacrylate Composite with UV and Thermal Curing Using Electro-Micromechanical Technique)

  • 박종만;공진우;김대식;이재락
    • 폴리머
    • /
    • 제27권3호
    • /
    • pp.189-194
    • /
    • 2003
  • Electro-micromechanical 시험법을 이용하여 탄소 섬유 강화 열경화성 수지 복합재료의 경화 방법에 따른 계면 평가와 손상 감지능 및 경화 모니터링에 대해 고찰하였다. 경화 후 잔류 응력은 전기 저항 측정을 통해 모니터링 하였으며, 경화 방법에 따라 상호 비교하였다. 기지 재료의 인장 강도, 탄성률 및 계면 전단 강도는 열 경화의 경우가 자외선 경화보다 더 크게 나타났으며, 열 경화에서 경화 수축은 열팽창 계수 차이에 의한 잔류 응력 및 기지 재료의 수축에 의해 자외선 경화와 비교하여 더 크게 나타났다. 열 경화 시의 경화 중 전기 저항은 자외선 경화보다 더 큰 범위에서 변하였으며, 기지 재료의 기계적 물성과 계면 접착력에 의해 다르게 나타나는 겉보기 탄성률 또한 더 컸고, 같은 응력까지 더 빠르게 도달하였다.

나노인덴테이션을 이용한 나노물성 측정 (The measurement of nano properties using nanoindentation)

  • 권동일;이경우;김성훈;김주영;이윤희
    • 한국정밀공학회:학술대회논문집
    • /
    • 한국정밀공학회 2005년도 추계학술대회 논문집
    • /
    • pp.63-68
    • /
    • 2005
  • The nanoindentation technique is widely used to investigate the mechanical properties of nano-microscale materials. The nanoindentation method for assessing mechanical properties at low loads and shallow depths is already well established fur the characterization of thin films as well as bulk materials. In this study, we evaluated residual stress in DLC and Au thin films usign nanoindentation technique with a new stress-relaxation model. Moreover, We suggest a composite hardness equation and quantify the magnitude of hardness increase by using an equation based on the interface hardness and the interface thickness, derived by comparing results derived from this equation and those determined in nanoindentation tests. Finally, We present an indentation size effect (ISE) model that extends the available contact depth for ISE application down to several tens of nanometers by considering the tip bluntness effect.

  • PDF

루프 종류의 FSS가 결합된 복합재료 구조의 잔류응력과 전파 투과 특성 (Study on Thermal Residual stresses and Transmission Characteristics in Loop Type Frequency Selective Surface Embedded Composite Structures)

  • 박경미;황인한;전흥재;홍익표;박용배;김윤재
    • Composites Research
    • /
    • 제26권5호
    • /
    • pp.279-288
    • /
    • 2013
  • 본 논문은 Loop 종류의 주파수 선택적 투과구조(FSS)를 결합시킨 복합재료 구조의 잔류응력으로 인한 층간분리, FSS의 손상 등 구조적 파손과 잔류응력으로 인해 변형된 FSS의 전파 투과 특성의 영향을 연구하였다. FSS는 단위요소 종류, 설계 변수, 배열에 따라 일정 대역에 전파를 투과 혹은 반사시킬 수 있다. 그래서 사각 루프 FSS를 복합재료와 결합시켰을 때 X-band(8~12 GHz)에서 공진이 발생하도록 설계한 후, 그에 따른 치수를 규격화하여 다른 루프형상(삼각 루프, 원형 루프)에 적용하고 단일 Loop와 이중 Loop 구조일 때 복합재료의 적층을 변화시켜 비교 분석하였다.

Experimental study on fatigue behavior of innovative hollow composite bridge slabs

  • Yang Chen;Zhaowei Jiang;Qing Xu;Chong Ren
    • Steel and Composite Structures
    • /
    • 제46권6호
    • /
    • pp.745-757
    • /
    • 2023
  • In order to study the fatigue performance of the flat steel plate-lightweight aggregate concrete hollow composite bridge slab subjected to fatigue load, both static test on two specimens and fatigue test on six specimens were conducted. The effects of the arrangement of the steel pipes, the amplitude of the fatigue load and the upper limit as well as lower limit of fatigue load on failure performance were investigated. Besides, for specimens in fatigue test, strains of the concrete, residual deflection, bending stiffness, residual bearing capacity and dynamic response were analyzed. Test results showed that the specimens failed in the fracture of the bottom flat steel plate regardless of the arrangement of the steel pipes. Moreover, the fatigue loading cycles of composite slab were mainly controlled by the amplitude of the fatigue load, but the influences of upper limit and lower limit of fatigue load on fatigue life was slight. The fatigue life of the composite bridge slabs can be determined by the fatigue strength of bottom flat steel plate, which can be calculated by the method of allowable stress amplitude in steel structure design code.

Welded plate and T-stub tests and implications on structural behavior of moment frame connections

  • Dong, P.;Kilinski, T.
    • Steel and Composite Structures
    • /
    • 제2권1호
    • /
    • pp.35-50
    • /
    • 2002
  • A series of tests on simple-welded plate specimens (SWPS) and T-stub tension specimens simulating some of the joint details in moment frame connections were conducted in this investigation. The effects of weld strength mismatch and weld metal toughness on structural behavior of these specimens were considered under both static and dynamic loading conditions. Finite element analyses were performed by taking into account typical weld residual stress distributions and weld metal strength mismatch conditions to facilitate the interpretation of the test results. The major findings are as follows: (a) Sufficient specimen size requirements are essential in simulating both load transfer and constraint conditions that are relevant to moment frame connections, (b) Weld residual stresses can significantly elevate stress triaxiality in addition to structural constraint effects, both of which can significantly reduce the plastic deformation capacity in moment frame connections, (c) Based on the test results, dynamic loading within a loading rate of 0.02 in/in/sec, as used in this study, premature brittle fractures were not seen, although a significant elevation of the yield strength can be clearly observed. However, brittle fracture features can be clearly identified in T-stub specimens in which severe constraint effects (stress triaxiality) are considered as the primary cause, (d) Based on both the test and FEA results, T-stub specimens provide a reasonable representation of the joint conditions in moment frame connections in simulating both complex load transfer mode and constraint conditions.

TiNi/A16061 형상기억복합재료의 미세조직 및 피로특성에 관한 연구 (A Study on the Microstructure and Fatigue Properties of TiNi/A16061 Shape Memory Composite)

  • 윤두표;박영철;김순국;이준희;이규창
    • 한국재료학회지
    • /
    • 제8권11호
    • /
    • pp.993-998
    • /
    • 1998
  • 본 연구는 형상기억합금을 이용하여 제조한 신소재 중의 하나인 형상기억복합재료를 소개하고자 한다. 이 복합재료는 TiNi 섬유의 형상기억효과로 금속복합재료의 취약점이라 할 수 있는 기지와 섬유간의 열팽창차이로 인한 인장잔류응력을 제거하고 기지내에 압축잔류응력을 발생시켜 높은 인장강도를 갖는다. 따라서 본 연구에서는 용탕단조법으로 복합재료를 제조한 후 미세조직을 관찰하고 TiNi 섬유의 역변태온도 이상에서 피로실험을 수행하여 복합재료의 피로특성을 검토하였다. 이 결과 363K에서의 피로균열전파제어효과는 섬유체적률과 예변형에 의하여 증가된다.

  • PDF

동시경화 강철-복합재료 원형 단일 겹치기 조인트의 최적설계 (Optimum Design of Co-cured Steel-Composite Tubular Single Lap Joints)

  • 조덕현;이대길
    • 대한기계학회논문집A
    • /
    • 제24권5호
    • /
    • pp.1203-1214
    • /
    • 2000
  • In this paper, a failure model for co-cured steel-composite tubular single lap joints has been proposed incorporating the nonlinear mechanical behavior of steel adherends and different failure mode s such as steel adherend failure and composite adherend failure. The characteristics of the co-cured steel-composite tubular single lap joint were investigated with respect to the test temperature, the stacking sequence of composite adherend, the thickness ratio of steel adherend to composite adherend, and the scarf ratio of steel adherend. Thus, the optimum design method for the co-cured steel-composite tubular single lap joint was suggested.

$Si_3N_4/SM45C$ 접합부의 응력해석 및 파괴특성 (Fracture Characteristics and Stress Analysis of $Si_3N_4/SM45C$ Joint)

  • 김기성
    • 한국공작기계학회:학술대회논문집
    • /
    • 한국공작기계학회 1998년도 추계학술대회 논문집
    • /
    • pp.248-253
    • /
    • 1998
  • Recently, the uses of Ceramic/metal bonded joints, resin/metal joints, adhesive joints, composite materials which are composed of dissimiliar materials have increased in various industry fields. Since the ceramic/metal bonded joints material is made at a high temperature, residual stress distributions due to differences in material properties were investigated by varying material parameters. The two dimensional finite element analysis was performed to study residual stress distribution in Si3N4/SM45C bonded joint with a copper interlayer between the silicon nitride(Si3N4) and the structural carbon steel(SM45C) and 4-point bending tests were carried out under room temperature. Fracture surface and crack propagation path were observed using scanning electron microscope and characteristics of its fracture was discussed.

  • PDF

CFRP 복합재압력용기의 충격후 잔류강도저하특성 평가 (Evaluation of the Residual Strength of CFRP Composite Pressure Vessel After Low Velocity Impact)

  • 박재범;김동륜;황태경
    • 한국추진공학회:학술대회논문집
    • /
    • 한국추진공학회 2009년도 제33회 추계학술대회논문집
    • /
    • pp.439-442
    • /
    • 2009
  • 본 논문에서는 CFRP 복합재 압력용기의 저속충격후 잔류강도 저하량의 정량적인 연구 결과에 대해 논한다. 낙하식 충격시험을 이용하여 복합재 압력용기에 다양한 충격에너지별 충격하중을 가한 후, 압력용기를 원환시험편으로 가공하여, 각 시험편의 원주방향 파열압력이 측정되었다. 또한, 유한요소모델을 구축하여 충격에너지별 변형거동과 응력분포에 대해서도 고찰하였다. 본 연구결과 저속 충격후 CFRP 복합재 압력용기의 잔류강도 저하량을 정량적으로 평가할 수 있는 실험기법이 개발되었다.

  • PDF