• Advanced Composite Materials
• /
• 제16권4호
• /
• pp.283-298
• /
• 2007

Environment-friendly composites reinforced with bagasse fiber (BF), a kind of natural fiber as the remains from squeezed sugarcane, were fabricated by injection molding and press molding. As appropriate matrices for injection molding and press molding, polypropylene (PP) and polycaprolactone-cornstarch (PCL-C) were selected, as a typical recyclable resin and biodegradable resin, respectively. The mechanical properties of BF/PP composites were investigated in view of fiber mass fraction and injection molding conditions. And the mechanical properties and the biodegradation of BF/PCL composites were also evaluated. In the case of injection molding, the flexural modulus increased with an increase in fiber mass fraction, and the mechanical properties decreased with an increase in cylinder temperature due to the thermal degradation of BF. The optimum conditions increasing the flexural properties and the impact strength were $90^{\circ}C$ mold temperature, 30 s injection interval, and in the range of 165 to $185^{\circ}C$ cylinder temperature. On the other hand, as to BF/PCL-C fully-green composites, both the flexural properties and the impact strength increased with an increase in fiber mass fraction. It is considered that the BF compressed during preparation could result in the enhancement in mechanical properties. The results of the biodegradability test showed the addition of BF caused the acceleration of weight loss, which increased further with increasing fiber content. This reveals that the addition and the quantities of BF could promote the biodegradation of fully-green composites.

• 한국기계가공학회지
• /
• 제10권5호
• /
• pp.131-136
• /
• 2011

Many researchers are recently studying about Electroactive polymer(EAP). But it has a physical limitation, because of property of material. Carbon nanotube(CNT) is known as the promising material which has excellent electro-mechanical characteristics and is mostly defect-free. It is expected that a successful synthesis of CNT and Nafion known as a primary material for IPMC would make a great improvement on its electro-mechanic feature. This study focuses on the method of synthesis of CNT with Nafion which improves electro-mechanical characteristic. To come up with mechanical dispersion with Nafion and Isopropyl Alcohol(IPA), we dispersed Single-walled carbon nanotubes(SWCNTs). For a uniformly layer of CNT, we used a spray gun on a hot plate by a simplified method. We fabricated a disperse SWCNT/Nafion composite uniformly. Through the use of the E-beam evaporator to form an uniform electrode layer, we consummated the IPMC actuator. This result shows improving 1.5 times mechanical properties about driving force in IPMC.

• Advanced Composite Materials
• /
• 제18권4호
• /
• pp.297-314
• /
• 2009

A design method is proposed to optimize the stacking sequence of laminated composite plates for desired vibration characteristics. The objective functions are the natural frequencies of the laminated plates, and three types of optimization problems are studied where the fundamental frequency and the difference of two adjacent frequencies are maximized, and the difference between the target and actual frequencies is minimized. The design variables are a set of discrete values of fiber orientation angles with prescribed increment in the layers of the plates. The four lamination parameters are used to describe the bending property of a symmetrically laminated plate, and are optimized by a gradient method in the first stage. A new technique is introduced in the second stage to convert from the optimum four lamination parameters into the stacking sequence that is composed of the optimum fiber orientation angles of all the layers. Plates are divided into sub-domains composed of the small number of layers and designed sequentially from outer domains. For each domain, the optimum angles are determined by minimizing the errors between the optimum lamination parameters obtained in the first step and the parameters for all possible discrete stacking sequence designs. It is shown in numerical examples that this design method can provide with accurate optimum solutions for the stacking sequence of vibrating composite plates with various boundary conditions.

• Composites Research
• /
• 제24권4호
• /
• pp.1-4
• /
• 2011

수정된 Hummer's 방법으로 제조된 산화그래핀(graphene oxide, GO)을 이용하여 PMMA와 Nylon 6,6에 분산시켜 각각 복합재료 섬유와 필름으로 제조하고 동적기계적 물성과 인장특성을 분석하였다. 동적기계적 분석과 인장 특성에서 GO-PMMA 복합재료 섬유는 GO의 효율적 기계적 물성 보강 효과를 확인 하였으나 Nylon 6,6 복합재료는 제조과정에서 사용된 포름산의 낮은 pH로 인해 산화그래핀의 분산안정성이 저하되어, 낮은 보강효율을 보임을 알 수 있었다.

• 한국분말재료학회지
• /
• 제13권3호
• /
• pp.172-177
• /
• 2006

Aging characteristics and mechanical properties of commercial 7xxx series Al composites were investigated from viewpoint of ceramic contents. After sintering process, sintered densities of blended and composite powder were 95 and 97%, respectively. Each part was solution-treated at $475^{\circ}C$ for 60 min and aged $175^{\circ}C$. And two-step aging was also performed form $120^{\circ}C$ to $175^{\circ}C$. The aging behavior of the sintered composite pow-der was different from that of sintered blended powder. The peak aging time of the composite was rapid as well due to strain. Before aging, mechanical properties of sintered composite powder was significantly higher than that of sintered blended powder. These increments of properties were directly affected by ceramic particles. However, after aging, incremental rate of mechanical properties was slowed in the composite.

• Elastomers and Composites
• /
• 제46권4호
• /
• pp.318-323
• /
• 2011

폐타이어고무분말을 재활용하기 위하여 방수시트용 고무분말 복합체를 제조하였으며, 수지 종류와 가교제의 함량이 복합체의 기계적 특성에 미치는 영향을 고찰하였다. EPDM이 부가됨에 따라 고무분말 PE 복합체의 신장율이 3배 이상 증가하는 현상을 나타내었다. 고무분말 충전 복합체에 가교제의 농도가 증가함에 따라 복합체의 강도가 증가하였으며, 특히 재생 폴리프로필렌을 사용한 경우 3배 이상 인장강도가 현저하게 높게 나타났다. 따라서 폴리프로필렌 블렌드물로 고무분말 복합체를 제조하는 경우 신재 폴리프로필렌을 사용하는 것 보다 재생 폴리프로필렌을 사용하는 것이 기계적 특성면에서 효과적인 것으로 나타났다.

• Advanced Composite Materials
• /
• 제16권4호
• /
• pp.299-314
• /
• 2007

In the present study, natural fibers (jute, kenaf and henequen) reinforced thermoplastic (poly(lactic acid) and polypropylene) and thermosetting (unsaturated polyester) matrix composites were well fabricated by a compression molding technique using all chopped natural fibers of about 10 mm long, respectively. Prior to green composite fabrication, natural fiber bundles were surface-treated with tap water by static soaking and dynamic ultrasonication methods, respectively. The interfacial shear strength, flexural properties, and dynamic mechanical properties of each green composite system were investigated by means of single fiber microbonding test, 3-point flexural test, and dynamic mechanical analysis, respectively. The result indicated that the properties of the polymeric resins were significantly improved by incorporating the natural fibers into the resin matrix and also the properties of untreated green composites were further improved by the water treatment done to the natural fibers used. Also, the property improvement of natural fiber-reinforced green composites strongly depended on the treatment method. The interfacial and mechanical results agreed with each other.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.34-36
• /
• 2002

The objective of this study is to develop the composite insulator for 170kA disconnecting switch. In this paper, we have investigated the test procedure about each component(FRP tube, flange, shed) through technical standard(IEC 61462) and obtained demand characteristics by mechanical & electrical property test.

• 대한기계학회논문집A
• /
• 제25권10호
• /
• pp.1583-1589
• /
• 2001

Metal matrix composites with whisker reinforcements have significant potentials for demanding mechanical applications including defense, aerospace, and automotive industries. Especially metal matrix composites, which are reinforced with aluminum borate whisker, have been used leer the part of piston head in automobile because of good specific strength and wear resistance. In this study, AC4CH-based metal matrix composites with $Al_{18}$B$_{4}$ $O_{33}$ reinforcement have been produced using squeeze casting method, after T6 heat treatment, we evaluated fatigue life property of matrix and MMC composite and investigated fracture mechanism.m.

• Composites Research
• /
• 제27권6호
• /
• pp.236-241
• /
• 2014

본 연구에서는 공항 포장용 유지보수 재료로 사용되는 폴리머 콘크리트의 자외선 노출에 대한 기계적 물성 변화를 확인하기 위해 자외선 노출 전/후 시편의 압축강도 및 연성인자의 변화를 평가하였다. 현재 공항 포장용으로 사용되는 폴리머 콘크리트의 비율과 선행연구를 통해 얻은 최적 배합비율을 참고하여 시편을 제작하였다. 자외선 발생 램프의 출력을 고려하여 자연상태에서 노출되는 등가시간을 계산한 후 최대 3년에 해당하는 시간만큼의 등가시간 동안 시편을 노출시켰다. 실험결과, 자외선 노출 자체는 재료물성에 거의 영향을 주지 않았으며, 자외선 노출에 따른 온도상승에 의한 재료물성 변화가 주로 관찰되었다. 자외선에 의해 발생된 열에 노출된 후 모든 시편에서 인성은 감소하고, 압축강도는 증가하는 경향을 나타내었다.