• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2001년도 춘계학술발표대회 논문집
• /
• pp.244-249
• /
• 2001

In this paper, we present the simultaneous measurement of the fabricaition strain and temperature during and after cure of unsymmetric composite laminate uising fiber optic sensors. Fiber Bragg grating/extrinsic Fabry-Perot interferometric (FBG/EFPl) hybrid sensors are used to measure those measurands. The characteristic matrix of sensor is analytically derived and measurements can be done without sensor calibration. A wavelength-swept fiber laser is utilized as a light source. FBG/EFPI sensors are embedded in a graphite/epoxy unsymmetric cross-ply composite laminate at different direction and different location. We perform the real time measurement of fabrication strains and temperatures at two points of the composite laminate during cure process in an autoclave. Also, the thermal strains and temperatures of the fabricated laminate are measured in thermal chamber. Through these experiments, we can provide a basis for the efficient smart processing of composite and know the thermal behavior of unsymmetric cross-ply composite laminate.

• 센서학회지
• /
• 제8권6호
• /
• pp.440-447
• /
• 1999

지능형 복합재료 구조물(Smart Composite Structures) 사용 시 부하되는 인장하중과 복합재료의 경화 시 발생하는 열하중은 복합재료 내에 삽입된 광섬유 센서의 기계적 거동에 직접적인 영향을 미친다. 게다가 복합재료의 적층 순서 및 코팅층의 유무에 따라 광섬유 센서 내의 웅력 분포는 달라지게 된다. 또한, 복합재료 적층판 내에서 발생된 균열은 적층판 전체의 파괴뿐만 아니라 광섬유 센서의 파괴에 큰 영향을 미치게 된다. 그러므로, 본 연구에서는 인장하중 및 열하중이 가해지는 복합재료 적층판 내에 삽입된 광섬유 센서의 응력분포를 유한요소해석을 통해 알아보고, 복합재료 적층판의 적층 순서에 따른 영향과 광섬유 센서에 코팅을 하였을 경우 광섬유 센서 내의 응력분포에 미치는 영향을 알아보았다. 또, 인장실험을 통하여 적층판 내에서 발생한 균열이 광섬유 센서의 파괴에 미치는 영향을 알아보았다.

• 대한기계학회논문집
• /
• 제15권2호
• /
• pp.611-617
• /
• 1991

Effective stiffness of short fiber composite with a three-dimensional random orientation of fibers is derived theoretically and compared with available experimental data. The laminate analogy and transformed laminate analogy are used for modulus prediction of 2-D and 3-D random composites, respectively. The effective stiffness of random oriented fiber composite can be expressed in terms of longitudinal and transverse stiffnesses of unidirectional composites. The result of transformed laminate analogy is more accurate than other approaches such as, Christensen-Waals equational and Lavengood-Goettler equation, etc. Also the effective properties of random oriented fiber composite can be expressed in terms of fiber and matrix properties such as elastic modulus, shear modulus and Poisson's ratio.

• Composites Research
• /
• 제14권6호
• /
• pp.38-46
• /
• 2001

본 연구에서는, 전자파 흡수능을 가진 경사 복합재료 적층판를 설계할 수 있는 최적화 코드를 개발하였다. 또한, 유리 섬유/에폭시 직조 적층판, 알루미늄 첨가물을 함유간 유리섬유/에폭시 직조 적층판과 카본/에폭시 직조 적층판의 유전율을 구하고, 최적화 로드를 이용하여 3층형 전자파 흡수 복합재료 적층판을 개발하였다. 실험에 사용된 복합재료 적층판은 모두 전자기적으로 면내등방성을 가지며 따라서, 동축선과 망분석기를 이용하여 유전율을 측정하였다. 이 로드는 전자기적으로 직교이방성을 가지는 고분자기지 복합재료의 적층각을 포함한 다양한 변수를 고려할 수 있다.

• 한국정밀공학회지
• /
• 제12권12호
• /
• pp.130-138
• /
• 1995

Machined graphite/epoxy surfaces were studied by using SEM (Scanning Electron Microscopy), surface profilometry and its analysis to determine suitable surface describing parameters for machined unidirectional and multidirectional laminate composite. The surface roughness and profile are found to be highly depdndent on the fiber layup direction and the measurement direction. It was possible to machine 90 .deg. and -45 .deg. plies due to the adjacent plies, which were holding those plies. It was found that the microgeometrical variations in terms of roughness parameters $R_{a}$ without $D_{y}$(Maximum Damage Depth) region and $D_{y}$are better descriptors of the machined laminate composite surface than commonly used roughness parameters $R_{a}$and $R_{max}$ The characteristics of surface profiles in laminate composite are well represented in CPD (Cumulative Probability Distribution) plot and PPD (Percentage Probability Density) plot. Edge-trimmed multidirectional laminate surfaces are Gaussian and random for profiles measured along the tool movement direction, they are periodic and non-Gaussian in the direction perpendicular to the tool movement.t.ent.t.

• 한국자동차공학회논문집
• /
• 제15권6호
• /
• pp.50-61
• /
• 2007

The structural stiffness, strength and stability on the bodyshell and floor structures of the Korean Low Floor Bus composed of laminate, sandwich panels and metal reinforced frame were evaluated. The laminate composite panel and facesheet of sandwich panel were made of WR580/NF4000 glass fabric/epoxy laminate, while aluminum honeycomb or balsa was applied to the core materials of the sandwich panel. A finite element analysis was used to verify the basic design requirements of the bodyshell and the floor structure. The use of aluminum reinforced frame and honeycomb core was beneficial for weight saving and structural performance. The symmetry of the outer and inner facesheet thickness of sandwich panels did not affect the structural integrity. The structural strength of the panels was evaluated using Von-Mises criterion for metal structures and total laminate approach criterion for composite structures. All stress component of the bodyshell and floor structures were safely located below the failure stresses. The total laminate approach is recommended to predict the failure of hybrid sandwich composite structures at the stage of the basic design.

• 한국생산제조학회지
• /
• 제7권6호
• /
• pp.12-18
• /
• 1998

The optimal design for stiffened laminate composite cylindrical shells under combined loads is studied by a nonlinear mathematical search algorithm. The optimal design is accomplished with the CONMIN. several types of buckling modes with maximum allowable stresses and strains are included as constraints in the optimal design process, such as general buckling, panel buckling with either stringers or rings smeared out, local skin buckling, local crippling of stiffener segments. Rectangular or T type stringers and rectangular rings are used for stiffened laminate composite cylindrical shells.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2005년도 춘계학술발표대회 논문집
• /
• pp.141-145
• /
• 2005

Since the electromagnetic properties of fiber reinforced polymeric laminate composite can be tailored effectively by adjusting its composition and regulating the stacking sequence, it is plausible material for fabricating the radar absorbing structures (RAS) of desired performance. In order to design the effective electromagnetic wave (EM) absorber with the fiber reinforced polymeric laminate composite, its electromagnetic characteristics should be available and could be regulated easily in the target frequency bands. In this study, dielectric characteristics of the E-glass/epoxy laminate composites were measured by the free space method in the X-band frequency range ($8.2\;{\sim}\;12.4\;GHz$). In order to describe the dielectric behavior of laminate composites of arbitrary stacking sequences, the equivalent circuit model and the laminating equations for estimating dielectric properties were proposed, and experimentally verified. From the comparison of the predicted and measured data, the proposed method predicted well the experimentally measured data.

• International Journal of Aeronautical and Space Sciences
• /
• 제18권1호
• /
• pp.63-69
• /
• 2017

In this paper, composite laminate pull-through resistance was analyzed using the FEM method and compared with test results. 2D and 3D simplified FEM models, a nonlinear analysis, and a progressive failure analysis utilizing three composite laminate failure theories Maximum Stress, Maximum Strain, and Tsai-Wu were used to predict the FEM results with the test results. The load and boundary conditions of the test were applied to the FEM to simulate the test. A composite laminate pull-through test (ASTM D7332 Proc. B) was designed with a special fixture to collect more precise data. The test results were compared with the FEM analysis results.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1992년도 추계학술대회 논문집
• /
• pp.101-105
• /
• 1992

Machined graphite/epoxy composite surfaces were studied by using SEM(Scanning Electron Microscopy). surface profilometry and its analysis to determine suitable surface describing parameters for machined unidirectional and laminate composite surface. The surface roughness and profile are found to be highly dependent on the fiber layup direction and the measurement direction. Machined unidirectional and 0.deg. 45 .deg. 90 .deg. plies in laminate composite surface profiles are found to be Gaussian in the direction of machining. Since there exist bare fibers without matrix smearing in 0 .deg. ply, higher surface roughness values were found in this orientation. It was possible to machine 90 .deg. and -45 .deg. plies due to the adjacent plies, which were holding those plies. It was found that the microgeometrical variations in terms of roughness parameters Ra without Dy (maximum Damage Depth) region and Dy are better descriptors of the machined laminate composite surface than commonly used roughness parameters Ra and Ra. The characteristics of surface profiles in laminate composite are well represented in CHD (Cumulative Height Distribution) plot and PPD (Percentage Probability Density) plot. Also, the power spectral density function is shown to be capable of identifying the wavelength distribution of the machining damage.