• 대한치과보철학회지
• /
• 제38권1호
• /
• pp.108-115
• /
• 2000

This study was designed to compare the effect of polishing on surface roughness of composite resin. We used Z100(3M) composite resin and placed the composite resin in the hole (4mm thick and 4mm in diameter) of vinyl plate and polymerized it under manufacturer's instructions. Samples were divided into 5 groups by polishing methods. Group 1 was control: resin was polymerized under glass plate, Group 2: resin was polymerized without any polishing procedure, Group 3: resin was polymerized with a polishing procedure of abrasive disc, Group 4: bonding agent was applyed in thin layer and polymerized on the polished polymerized resin surface. Group 5: resin was polymerized under transparent celluloid strip. The surface roughness of each specimen was measured with Sufacoder SEF-30D (Kosaka lab. Ltd) under 0.08mm cut off, 0.05mm/s stylus speed, ${\times}40$ horizontal magnification, ${\times}5000$ vertical magnification. The results were as follows : 1. Group 1 showed the most smooth surface in this study. 2. Group 3 showed more rough surface than Group 2. Considering the surface roughness, it would be better to make the shape completely before polymerize the resin. To finish and polish after the polymerization of resin makes less smooth surface. 3. When we use the transparent celluloid strip, minimum finishing procedures are recommended. Any polishing procedure could not recover the smooth resin surface of celluloid strip. 4. Application and polymerization of the thin layer of bonding agent on the polished surface showed the minimum surface smoothing effect.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.971-974
• /
• 2011

Aluminum matrix composites reinforced with SiC particles(AMC) are one of the candidate materials for the weight reduction of rolling stock brake discs. It is known that weight reduction of about 40% is possible when they replace conventional cast iron brake discs. But casting is not easy because of bad wettability of SiC with Al alloy. We developed two AMC brake discs with SiC volume fraction of 20% by a new casting method. It was found the developed method produced brake discs of good quality.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 추계학술대회 논문집
• /
• pp.197-198
• /
• 2006

• Journal of Electrical Engineering and Technology
• /
• 제10권4호
• /
• pp.1796-1803
• /
• 2015

While considering the current scenario, in this world power demand goes on increases day by day. Frequent power outages occur in high voltage transmission line due to the deprived performance of polluted insulators; this affects overall operation of power system and may indirectly impinge on the growth of production sector. Many researchers are keenly taking efforts to provide highly reliable and stable power to neediest. In this paper, A.C pollution flashover performance of disc type glass insulator and composite long rod insulators investigation under various artificial pollutions by varying Equivalent Salt Density Deposition (ESDD) levels. Here, we use different types of pollution methods like binding method, dipping method and spraying methods with different types of pollutants concentration. Based on dimensional analysis, four different Mathematical models have been developed to predict the A.C pollution Flashover Voltage (FOV) of insulators. Both the experimental and mathematically modeled results are compared; it's observed that mathematical model 3 yields better results.

• 한국분말재료학회지
• /
• 제20권5호
• /
• pp.345-349
• /
• 2013

Carbon nanotube-dispersed bismuth telluride matrix (CNT/$Bi_2Te_3$) nanopowders were synthesized by chemical routes followed by a ball-milling process. The microstructures of the synthesized CNT/$Bi_2Te_3$ nanopowders showed the characteristic microstructure of CNTs dispersed among disc-shaped $Bi_2Te_3$ nanopowders with as an average size of 500 nm in-plane and a few tens of nm in thickness. The prepared nanopowders were sintered into composites with a homogeneous dispersion of CNTs in a $Bi_2Te_3$ matrix. The dimensionless figure-of-merit of the composite showed an enhanced value compared to that of pure $Bi_2Te_3$ at the room temperature due to the reduced thermal conductivity and increased electrical conductivity with the addition of CNTs.

• 한국식품영양과학회지
• /
• 제45권5호
• /
• pp.778-781
• /
• 2016

본 연구에서는 폐기되는 성게 껍질을 이용한 생분해성 필름소재를 개발하고자 gelatin을 첨가한 복합필름 및 항산화, 항균성을 부여하기 위해 아까시 꽃 추출물(RFE)을 첨가한 필름을 제조하였다. 그 결과 gelatin 비율이 증가함에 따라 성게 껍질 필름의 인장강도가 증가하였고 신장률이 감소하였으며, 성게 껍질과 gelatin을 8:2 비율로 첨가하였을 때 최적의 물성을 보였다. 또한, 필름에 RFE를 첨가함에 따라 인장강도는 감소하였으나 신장률과 필름 투습도는 증가하였다. RFE 함유 성게 껍질 필름의 ABTS, DPPH 라디칼 소거능 측정과 디스크 확산법을 이용하여 항산화 및 항균 능력을 측정하였는데, RFE 농도가 증가함에 따라 항산화, 항균 능력이 향상하였다. 따라서 본 연구 결과, RFE를 첨가한 생분해 성게 껍질 필름은 적절한 물성과 함께 항산화, 항균 능력이 있기에 가공식품의 저장성을 증대시킬 수 있는 기능성 포장 소재로의 활용이 가능하다고 판단된다.

• Restorative Dentistry and Endodontics
• /
• 제49권1호
• /
• pp.7.1-7.11
• /
• 2024

Objectives: This study aimed to evaluate the impact of substrate color and interface distance on the color adjustment of 2 single-shade composites, Vittra APS Unique and Charisma Diamond One. Materials and Methods: Dual disc-shaped specimens were created using Vittra APS Unique or Charisma Diamond One as the center composite, surrounded by shaded composites (A1 or A3). Color measurements were taken with a spectrophotometer against a gray background, recording the color coordinates in the CIELAB color space. Illumination with a light-correcting device and image acquisition using a polarizing filter-equipped cell phone were performed on specimens over the same background. Image processing software was used to measure the color coordinates in the center and periphery of the inner composite and in the outer composite. The color data were then converted to CIELAB coordinates and adjusted using data from the spectrophotometer. Color differences (ΔE₀₀) between the center/periphery of single-shade and outer composites were calculated, along with color changes in single-shade composites caused by different outer composites. Color differences for the inner composites surrounded by A1 and A3 were also calculated. Data were analyzed using repeated-measures analysis of variance (α = 0.05). Results: The results showed that color discrepancies were lowest near the interface and when the outer composite was whiter (A1). Additionally, Charisma Diamond One exhibited better color adjustment ability than Vittra APS Unique. Conclusions: Color discrepancies between the investigated single-shade composites diminished towards the interface with the surrounding composite, particularly when the latter exhibited a lighter shade.

• 대한치과보철학회지
• /
• 제29권1호
• /
• pp.91-109
• /
• 1991

The purpose of this study were to comfirm the effects of the thickness and kinds of porcelain, etchants, illumination time, elapsed time for the measurement, and chemical cure component to the bond strength of porcelain laminate and composite resin cement, and to compare the effects between the light cured resin and the dual cured resins. The etched porcelain surface, the sectioned surface crossing porcelain and resin after bonding, and the debonded surfaces were observed by the SEM. One product of laminate porcelain powder, one light cured resin and two dual cured resins were selected. Each resin cements are lightened through the thin porcelain disc which was cut from cylindrical porcelain specimen by the diamond saw, and by the light through the porcelain disc they were bonded. Changes of thickness and kinds of porcelain, etchants, illumination time, and the elapsed time for the measurement were considered as variables for the bond strength. And the bond strength of porcelain and dual cured resins under the conditions of autopolymerization or the removal of chemical cure component were measured and compared. Bond strength were measured by shear stress. The etched surface, the cross-sectioned surface, and the debonded surface of porcelain or resin were observed by SEM. On the summary of this study, the following conclusions can be stated; 1. Bond strength of light cured resin was decreased inversely by the thickened porcelain laminate and showed the lowest value to the masking dentin porcelain among 4 kinds of porcelain powder. 2. Bond strength of autopolymerization of dual cured resin without illumination in dark chamber were from 75% to 98% to the data of dual cured resin with illumination. 3. Bond strength of dual cured resin used without chemical cured components were same to them of light cured resin. 4. Cross-sectioned surface treated by silane did not show the gap between the porcelain and resin. 5. Illumination over 80 seconds did not make the significant increase of bond strength on all kinds of resin.

• 대한의용생체공학회:의공학회지
• /
• 제21권3호
• /
• pp.285-293
• /
• 2000

나이에 의한 외부의 환경조건의 변화는 이에 적응하려는 척추의 구조적인 변화를 가져온다. 이러한 구조적인 변화는 척추의 biomechanical 거동에 영향을 미칠 것이다. 이러한 구조적인 변화의 효과를 연구하기 위하여, 나이에 의한 척추의 재료 및 기계적인 물성의 변화는 제외되었다. 유한요소법 (finite element method)에 의한 lumbar spine model (L3-L4)에 있어서, Annulus 의 유한요소 모델은 laminate composite elements로서 16개의 layer와 6개의 물성으로 구성되어있다. Spinal stiffness 와 facet reaction은 나이가 들수록 증가했다. 나이가 들수록 inner annulus의 fiber/layer tensile strains, cancellous bone stress 및 end-Plate stress는 감소했다. Fiber/layer compressive strains, facet reaction, ligament reaction and end-plate rigidity는 나이에 의한 척추의 구조적인 변화에 의하여 증가했다. 따라서 나이에 의한 척추의 정상적인 쇠퇴과정에 있어서 척추의 구조적인 변화는 spinal stiffness를 증가 시켜서 척추 및 disc의 지나친 변형을 감소시킬 것이다.

• 소성∙가공
• /
• 제4권4호
• /
• pp.398-409
• /
• 1995

The wear properties of the alumina short fiber reinforced tin-bronze matrix composites manufactured by hot pressing was studied at the room temperature and $350^{\circ}C.$ The wear loss of various specimens having different constituent and different density was examined by a pin-on-disc type wear testing machine. The results were discussed by the observation of the worn surface morphology and the analysis of the composition on the worn surfaces. Since the reinforced effect of the alumina fiber on the wear resistance was dependent on the strength of alloy matrix, the pressureless sintered composites having a lower matrix strength showed a marked increase in wear resistance by the fiber reinforcement. As the wear condition became severe, the fiber reinforcement was more effective. The delamination on the wear surface was observed in the pressureless sintered specimens having pores which are related to the initiation and the propagation of cracks. However, the wear mechanism acting on a big failure area was not found on the wear surfaces of the hot pressed specimens having a few pores.