• Computers and Concrete
• /
• v.21 no.3
• /
• pp.321-333
• /
• 2018

Flat-slabs, being a significant structural component, not only reduce the dead load of the structure but also reduce the amount of concrete required for construction. Moreover the use of recycled aggregates lowers the impact of large scale construction to nearby ecosystems. Recycled aggregate based concrete being a quasi-brittle material shows enormous cracking during failure. Crack growth in flat-slabs is mostly in sliding mode (Mode II). Therefore sufficient sections need to be provided for resistance against such failure modes. The main objective of the paper is to numerically determine the ultimate load carrying capacity of two self-similar flat-slab specimens and validate the results experimentally for the natural aggregate as well as recycled aggregate based concrete. Punching shear experiments are carried out on circular flat-slab specimen on a rigid circular knife-edge support built out of both normal (NAC) and recycled aggregate concrete (RAC, with full replacement). Uniaxial compression and bending tests have been conducted on cubes, cylinders and prisms using both types of concrete (NAC and RAC) for its material characterization and use in the numerical scheme. The numerical simulations have been conducted in ABAQUS (a known finite element software package). Eight noded solid elements have been used to model the flat slab and material properties have been considered from experimental tests. The inbuilt Concrete Damaged Plasticity model of ABAQUS has been used to monitor crack propagation in the specimen during numerical simulations.

• Geomechanics and Engineering
• /
• v.12 no.5
• /
• pp.863-870
• /
• 2017

With the increasing interest in using bacterial biofilms in geo-engineering practices, such as soil improvement, sealing leakage in earth structures, and hydraulic barrier installation, understanding of the contribution of bacterial biofilm formation to mechanical and hydraulic behavior of soils is important. While mechanical properties of soft gel-like biofilms need to be identified for appropriate modeling and prediction of behaviors of biofilm-associated soils, elastic properties of biofilms remain poorly understood. Therefore, this study investigated the microscale Young's modulus of biofilms produced by Shewanella oneidensis MR-1 in a liquid phase. The indentation test was performed on a biofilm sample using the atomic force microscopy (AFM) with a spherical indentor, and the force-indentation responses were obtained during approach and retraction traces. Young's modulus of biofilms was estimated to be ~33-38 kPa from these force-indentation curves and Hertzian contact theory. It appears that the AFM indentation result captures the microscale local characteristics of biofilms and its stiffness is relatively large compared to the other methods, including rheometer and hydrodynamic shear tests, which reflect the average macro-scale behaviors. While modeling of mechanical behaviors of biofilm-associated soils requires the properties of each component, the obtained results provide information on the mechanical properties of biofilms that can be considered as cementing, gluing, or filling materials in soils.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.2
• /
• pp.959-968
• /
• 2017

Electrical safety monitoring System (ESMS) is a critical component in modern power systems, which is characterized by large-scale access points, massive users and versatile requirements. For convenience of the information integration and analysis, the software development, maintenance, and application in the system, the cloud platform based ESMS is established and assessed in this paper. Firstly the framework of the system is proposed, and then the assessment scheme with a set of evaluation indices are presented, by which the appropriate cloud product can be chosen to meet the requirements of a specific application. Moreover, to calculate the weights of the evaluation indices under uncertainty, an improved interval AHP method is adopted to take into consideration of the fuzziness of expert scoring, the qualitative consistency test, and the two normalizations in the process of eigenvectors. Case studies have been made to verify the feasibility of the assessment approach for ESMS.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.12 no.3
• /
• pp.33-54
• /
• 2016

In the modern society based on information and communication, which is exposed to the risks of a lot of information security breaches, corporate information assets may be an economical scale in a country. Most of damages derived from corporate technological information leak often occur in small and medium corporations. Although many information security managers in corporations have focused on certification systems such as information security management system, small and medium corporations are poorly aware of the information security, and their environments surrounding it should be also improved. In addition, it is difficult to expect spontaneous participations in it, since the sustainable information security management systems are often not forced to be certified. Thus, the purpose of this study is to examine plans to improve small and medium corporations' technological protections by using some component of the information security management system. On the basis of this examination, it also attempts to discuss some methods for effective and efficient information security in the small and medium corporations' technological protections.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.97-100
• /
• 2003

Globally, the various machine components, as in electronics and communications, are demanded to being high-performance and micro-scale with abrupt development of the fields of computers, mobile communications. As this current tendency, production of the parts that must have high accuracy, so called milli-structure, are accomplished by the method of top-down, differently as in the techniques of MEMS, NANO. But, in the case of milli-structure, production procedure is highly costs, difficult and demands more accurate dimension than the conservative forming, processing technique. In this paper, forming analysis of the micro-former as the milli-structure are performed and then calculate the punch force etc. This information calculated is applied to decide the forming capacity of micro-former and design the process of forming stage, dimension of dies in another forming bodies. And, for the better precise forming analysis, elasto-plastic analysis is to be performed, then the consideration about effect of elastic recovery when punch and die are unloaded, have to be discussed in change of dimensions.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1992.10a
• /
• pp.140-154
• /
• 1992

The objective of the research stated here was aimed at providing the information needed to establish the Korean Seismic Design Code Recommendations and Guides for precast concrete (P.C) large panel apartment buildings. This was accomplished by investigation and analysis of the response of P.C large panel structures subjected to shaking table excitation simulating earthquake ground motion. one of the test specimens used was 1/3-scaled 3-story box P.C model provided by Sam-Hwan Camus Corporation. The 4m $\times$4m shaking table was used to simulate the earthquake ground motion. the employed input accelerogram was the one recorded as Taft N21E component and the peak ground acceleration(PGA) was scaled depending on the desired level of seismic severity and the time according to dynamic similitude rule. Based on results obtained from shaking table test of this P.C model, the following conclusions were drawn . (1) As far as test specimen is concerned, the seismic safety factors turns out to be 7~8. (2)P.C model has damping ratio of about8% which is twice larger than in-situ R.C. structure. And (3)this model has global displacement ductility ratio of 2~3 through the energy dissipation by opening and sliding of joints.

• Research in Community and Public Health Nursing
• /
• v.21 no.2
• /
• pp.156-168
• /
• 2010

Purpose: The purpose of this study was to construct a questionnaire to assess male workers' sobriety behavior based on Ajzen's Theory of Planned Behavior (TPB). Methods: A primary questionnaire with 56 questions was constructed based on literature review and structured interview with male workers. The Content Validity Index (CVI) was evaluated by a group of experts, construct validity was tested by principle component analysis, and reliability was evaluated by Cronbach's ${\alpha}$ and the test-retest reliability test. Results: Fifty two questions showed higher than .8 of CVI. Four factors explained 78.71% of the total variance among items for sobriety intention and direct measure, and six factors explained 67.99% of the total variance among indirect measure items and those factors coincided with the variables of TPB in factor analysis. Cronbach's ${\alpha}$ of this questionnaire was .873 and the result of test-retest reliabilty test was relatively reliable. A total of 41 items with 7-point scale were constructed in the final version. Conclusion: This questionnaire was valid and reliable to measure sobriety behavior based on TPB in male workers. It can be useful to evaluate the result of a sobriety program for male workers.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2003.10a
• /
• pp.24-29
• /
• 2003

Deep sea water has cold temperature, abundant nutrients and minerals, and good water quality that is pathogen-free and stable. Compared with surface water, deep sea water contains more nutrition salt, such as nitrogen and phosphor. Moreover, if has the good balance of minerals. Because of the ability of the spray drying process to produce a free-flowing power considering of spherical particles with a well-defined size distribution and the rapid drying times for heat-sensitive material, spray drying is attractive for a wide range of applications spray drying is a unique unit operation in which powders are produced from a liquid feed in a single processing step. Key component of the process are atomizer, spray chamber. Design of spray chamber should be based on the atomizer type, the production rate, and the particle size required. Because of the complex processes taking place during spray drying, traditional design method are based on pilot-plant tests and empirical scale-up rules. Modern technique such as CFD have a role to play in design and troubleshooting.

• Journal of the Korean earth science society
• /
• v.39 no.4
• /
• pp.361-377
• /
• 2018

The purpose of the study was to define five science core competencies introduced in the 2015 revised science curriculum with each component and practical indicators into the frame. Science teachers on site could use it in teaching and developing science program to equip students with the competencies to creatively solve problems which is the aim of science education in the $21^{st}$ century. To develop this frame, we contacted 10 experienced science educators and collected the data through a questionnaire. We coded all responses and categorized into the components and practical indicators of each competency which were all compared with those from well-known theories in order to validate. We then contacted other 35 science educators again to construct the validity to fill out the survey of Likert scale. The finalized science core competency included 19 components in total with practical indicators that can be observable and measurable in the classroom. This frame was used to see how it fits into a STEAM program. The finding was that two different topics of the STEAM program displayed the different description of science core competency usage, which could be used as the prescription of the competency as to whether or not it is more promoted in science class.

• Journal of Power System Engineering
• /
• v.20 no.1
• /
• pp.50-56
• /
• 2016

This paper handled an investigation on the turbulent flow characteristics of three-dimensional small-size axial fan(SSAF) according to operating loads. Also, it was carried out by unsteady-state, incompressible and three-dimensional large eddy simulation(LES). The downstream flow type of SSAF is changed from axial flow to radial flow around the beginning of stall region at the aerodynamic performance curve. Axial mean velocity component largely grows around blade tip at the operating point of A to D, but transverse and vertical mean velocity components as well as Reynolds shear stresses highly develop around blade tip at the operating point of E to H. On the other hand, the peak value of turbulent kinetic energy developed around blade tip shows the highest at the operating point of E.