• The Journal of the Korea institute of electronic communication sciences
• /
• v.18 no.1
• /
• pp.45-52
• /
• 2023

The power generation method using expensive diesel has operation problems such as high cost diesel generator and a lack of reserved power due to increase of power demand in some islands, requiring expansion of power generation facilities. To solve this problems, it is necessary to improve the efficiency of power generation facilities through an ORC(Organic Rankin Cycle) system application that uses waste heat as a heat source. Therefore, localized application technology of price competitive and highly reliable ORC power generation system is needed, and optimization technology of generators is having great effect, so this study performed two generator designs to get a high-efficiency generator with an optimized 30kW output. The comparison of simulation data for two designed models showed that a generator with SPM factor of 46.2% had an efficiency of 92.1% and a power ouput of about 23.2kW based on 12,000rpm, a generator with SPM factor of 44.46%, had a power output of 27.9kW and efficiency of 93.6% based on above rpm. For the verification of improved design model with SPM factor of 44.46%, the prototype test system with 110kW motor dynamometer was installed and got to the efficiency of 92.08% with conditions of the rated capacity 25kW at 12,000rpm, the test results of prototype generator showed the validity of generator design.

• Wind and Structures
• /
• v.10 no.4
• /
• pp.367-382
• /
• 2007

A nonlinear numerical method was developed to assess the stability of suspension bridge catwalks under a wind load. A section model wind tunnel test was used to obtain a catwalk's aerostatic coefficients, from which the displacement-dependent wind loads were subsequently derived. The stability of a suspension bridge catwalk was analyzed on the basis of the geometric nonlinear behavior of the structure. In addition, a full model test was conducted on the catwalk, which spanned 960 m. A comparison of the displacement values between the test and the numerical simulation shows that a numerical method based on a section model test can be used to effectively and accurately evaluate the stability of a catwalk. A case study features the stability of the catwalk of the Runyang Yangtze suspension bridge, the main span of which is 1490 m. Wind can generally attack the structure from any direction. Whenever the wind comes at a yaw angle, there are six wind load components that act on the catwalk. If the yaw angle is equal to zero, the wind is normal to the catwalk (called normal wind) and the six load components are reduced to three components. Three aerostatic coefficients of the catwalk can be obtained through a section model test with traditional test equipment. However, six aerostatic coefficients of the catwalk must be acquired with the aid of special section model test equipment. A nonlinear numerical method was used study the stability of a catwalk under a yaw wind, while taking into account the six components of the displacement-dependent wind load and the geometric nonlinearity of the catwalk. The results show that when wind attacks with a slight yaw angle, the critical velocity that induces static instability of the catwalk may be lower than the critical velocity of normal wind. However, as the yaw angle of the wind becomes larger, the critical velocity increases. In the atmospheric boundary layer, the wind is turbulent and the velocity history is a random time history. The effects of turbulent wind on the stability of a catwalk are also assessed. The wind velocity fields are regarded as stationary Gaussian stochastic processes, which can be simulated by a spectral representation method. A nonlinear finite-element model set forepart and the Newmark integration method was used to calculate the wind-induced buffeting responses. The results confirm that the turbulent character of wind has little influence on the stability of the catwalk.

• Journal of Astronomy and Space Sciences
• /
• v.29 no.4
• /
• pp.381-387
• /
• 2012

The planetary exploration rover executes various missions after moving to the target point in an unknown environment in the shortest distance. Such missions include the researches for geological and climatic conditions as well as the existence of water or living creatures. If there is any obstacle on the way, it is detected by such sensors as ultrasonic sensor, infrared light sensor, stereo vision, and laser ranger finder. After the obtained data is transferred to the main controller of the rover, decisions can be made to either overcome or avoid the obstacle on the way based on the operating algorithm of the rover. All the planetary exploration rovers which have been developed until now receive the information of the height or width of the obstacle from such sensors before analyzing it in order to find out whether it is possible to overcome the obstacle or not. If it is decided to be better to overcome the obstacle in terms of the operating safety and the electric consumption of the rover, it is generally made to overcome it. Therefore, for the purpose of carrying out the planetary exploration task, it is necessary to design the proper suspension system of the rover which enables it to safely overcome any obstacle on the way on the surface in any unknown environment. This study focuses on the design of the new double 4-bar linkage type of suspension system applied to the Korea Aerospace Research Institute rover (a tentatively name) that is currently in the process of development by our institute in order to develop the planetary exploration rover which absolutely requires the capacity of overcoming any obstacle. Throughout this study, the negative moment which harms the capacity of the rover for overcoming an obstacle was induced through the dynamical modeling process for the rocker-bogie applied to the Mars exploration rover of the US and the improved version of rocker-bogie as well as the suggested double 4-bar linkage type of suspension system. Also, based on the height of the obstacle, a simulation was carried out for the negative moment of the suspension system before the excellence of the suspension system suggested through the comparison of responding characteristics was proved.

• Journal of Soil and Groundwater Environment
• /
• v.10 no.5
• /
• pp.1-10
• /
• 2005

Policies of the United States, the United Kingdom, the Netherlands, Germany and Denmark were compared and analyzed on risk assessment of contaminated sites. These countries were chosen from a feasible preliminary analysis of 18 countries of the European Union and the U. S. All the countries selected met two major criteria : I) implementation of risk assessment to determine the soil contamination and remediation targets of contaminated sites, ii) use of soil guidance values and risk assessment as complementary measures to determine soil contamination. Suggested policy improvements to Korea regarding these issues include i) legislation of a rational risk assessment methodology of contaminated sites, and ii) enactment of collaboration of risk assessment with the soil guidance values. To establish effective risk assessment legislation, additional in-depth research on social, economic and long-term effects of the proposed risk assessment methodologies, as well as the mutual consent of all parties including academia, industry, and administration will be necessary. Linking risk assessment with soil guidance values would be applicable to a site contaminated where the contaminant concentration exceeds a certain soil guidance value. In parallel, application of risk assessment to a site where a contaminant concentration is naturally different such as mining sites would be plausible. The policy suggestions above are not yet conclusive due to a lack of policy implementation, and simulation. Thus, additional research on developing risk assessment methodology is needed. Nevertheless, initiation of the suggested policy would increase the efficacy of Korean policy regarding the survey and remediation of contaminated sites.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.3
• /
• pp.343-350
• /
• 2012

A planar solid oxide fuel cell (PSOFC) is studied in its application in a high-temperature stationary power plant. Even though PSOFCs with external reformers are designed for application from the distributed power source to the central power plant, such PSOFCs may sacrifice more system efficiency than internally reformed SOFCs. In this study, modeling of the PSOFC with an external reformer was developed to analyze the feasibility of thermal energy utilization for the external reformer. The PSOFC system model includes the stack, reformer, burner, heat exchanger, blower, pump, PID controller, 3-way valve, reactor, mixer, and steam separator. The model was developed under the Matlab/Simulink environment with Thermolib$^{(R)}$ modules. The model was used to study the system performance according to its configuration. Three configurations of the SOFC system were selected for the comparison of the system performance. The system configuration considered the cathode recirculation, thermal sources for the external reformer, heat-up of operating gases, and condensate anode off-gas for the enhancement of the fuel concentration. The simulation results show that the magnitude of the electric efficiency of the PSOFC system for Case 2 is 12.13% higher than that for Case 1 (reference case), and the thermal efficiency of the PSOFC system for Case 3 is 76.12%, which is the highest of all the cases investigated.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.3
• /
• pp.873-883
• /
• 2014

This study proposed an estimation method of allowable wave height for loading and unloading of the ship considering ship motion that is affected by ship sizes, mooring conditions, wave periods and directions. The method was examined validity by comparison with wave field data at pier $8^{th}$ in Pohang new harbor. The wave field data obtained with wave height of 0.10~0.75m and wave period of 7~13s in ship sizes of 800~35,000ton when a downtimes have occurred. On the other hand, the results of allowable wave height for loading and unloading of the ship in this method have obtained with wave heights of 0.19~0.50m and wave periods of 8~12s for ship sizes of 5,000, 10,000 and 30,000ton. Thus this method well reproduced the field data respond to various a ship sizes and wave periods. And the results of this method tended to decrease in 16~62% when have considered long wave, and it is decreased in 0~46% when didn't consider long wave than design standards in case of the ship sizes of 5,000~30,000ton, wave period of 12s and wave angle of $75^{\circ}C$. The allowable wave heights for loading and unloading of the ship proposed by design standards are didn't respond to various the ship sizes and wave periods, and we have found that the design standards has overestimated on smaller than 10,000ton.

• Publications of The Korean Astronomical Society
• /
• v.27 no.5
• /
• pp.419-429
• /
• 2012

In this paper, we propose a new re-quantization method after FFT processing to prevent the distortion of correlation result of VCS (VLBI Correlation Subsystem). The re-quantization is used to rearrange the data bit so as to reduce the data rate processed as 16-bit of FFT result of VCS. Having done this procedure, we found that the distorted spectrum of correlation result occurred in the delay tracking experiments by the re-quantization method introduced for initial design of VCS. In order to solve this, two kinds of re-quantization method, that is, the comparison and selection-type, are proposed. The first is to re-quantize the FFT result as a valid-bit by comparing with the input data after determining the adequate threshold. The second is manually to select the valid-bit of FFT result after finding the valid-field of data according to the bit-distribution of input data. We confirmed that the second is more effective compared with the first through the experimental result, and it will be implemented without so much modification of applied method in the condition of the limited resource of FPGA. The re-quantization is, however, carried out with 4-bit in the proposed second method for FFT result, and then the distortion of correlation result is also appeared. To fix this problem, the bit for re-quantization is extended to 8-bit. The proposed 8-bit selection-type is effectively verified so that the distortion of correlation result disappeared by applying to VCS in consequence of the simulation and correlation experiments.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.3B
• /
• pp.221-230
• /
• 2009

In Korea, many water intake plants are easily affected by effluents of sewage treatment plants because sewage treatment plants are usually located upstream or nearby the plants of the same riverine area. Furthermore, the inflow of harmful contaminants owing to pollutant spills or transportation accidents of vehicles using the roads and bridges intersecting the river causes significant impact on the management of water intake plants. Paldang lake, the main water intake plants in Korea, is especially exposed to various water pollution accidents, because the drainage basin area is significantly large compared to the water surface area of the lake. Therefore it is necessary to predict the possible pollutant spill in advance and consider measurements in case of water pollution. In this study, water quality prediction was performed in Paldang Lake in Korea durig the dry season using two-dimensional numerical models. In order to represent the cases of pollutant accidents, the difference of pollutant transport patterns with varying injection points was analyzed. Numerical simulations for hydrodynamics of water flow and water quality predictions were performed using RMA-2 and RAM4 respectively. As a result of simulation, the difference of pollutant transport with the injection points was analyzed. As a countermeasure against the pollutant accident, the augmentation of the flow rate is proposed. In comparison with the present state, the rapid dilution and flushing effects on the pollutant cloud could be expected with increase of flow rate. Thus, increase of flow rate can be used for operation of water intake plants in case of pollutant spill accidents.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.19 no.2
• /
• pp.138-144
• /
• 2013

Large and small marine accidents which are related to vessel's navigation are happening continuously and these maritime accidents have caused loss of lives and properties, and serious maritime environmental pollution damage. It is also true that maritime pollution damage is increasing due to these accidents, probability of growth of seaborne volume and complicated maritime traffic environment. Korea, recently, is developing an evaluation index which can assess sea risk through the evaluation of maritime traffic environment and provide danger and general information with relation to maritime traffic environment on target sea area to evaluate maritime traffic safety. In this paper, we intend to confirm the validity of maritime traffic safety on the basis of vessel navigator's risk consciousness and various sailing conditions by using the ship handling simulator. To confirm the validity of sailing vessel's maritime traffic safety, we use analysis of variance. By using analysis of variance, we analyze vessel navigator's characteristics, distance, speed and encounter type between vessels. Through multiple comparison of each factor's risk difference, we can confirm the change of numerical value of risk difference in statistical aspect.

• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.3
• /
• pp.162-171
• /
• 2014

In this study, the uncertainty analysis of present land pollutant load estimation with simplified land category in TMDLs was performed and the enhanced method for land pollutant load estimation with level II land cover consisting of 23 categories was suggested, which was verified by L-THIA model. For land TP load estimation in Jinwi stream basin, the result of comparison between existing method with simplified land category (Scenario 1) and enhanced method with level II land cover (Scenario 2) showed high uncertainty in existing method. TP loads estimated by Scenario 2 for land covers included in the site land category were in the range of 3.45 to 56.69 kg/day, in which TP loads differed by sixteen times as much among them. For application of scenario 2 to TMDLs, Land TP loads were estimated by matching level II land cover to 28 land categories in serial cadastral map (Scenario 3). In order to verify accuracy of TP load estimation by scenario 3, the simulation result of L-THIA was compared with that and the difference between the two was as little as 10%. The result of this study is expected to be used as primary data for accurate estimation of land pollutant load in TMDLs.