• International Journal of Highway Engineering
• /
• v.15 no.4
• /
• pp.11-20
• /
• 2013

PURPOSES : This study is to develop a method to evaluate the compaction effects of asphalt binders using WMA additives and compare their compaction effects on two types of WMA additives, two types of testing temperatures, and three types of asphalt film thicknesses. METHODS : This study is based on laboratory experiments and rheological analysis of the experimental results. Testing materials are aggregate disks, asphalt, and WMA additives. The main testing method is the stress sweep test by using dynamic shear rheometer (DSR). In addition, the testing parameters obtained from the stress sweep results to evaluate lubrication effects are complex modulus and LVE-Limit. RESULTS : At both the first compaction condition ($110^{\circ}C$, 0.3mm) and second compaction condition ($80^{\circ}C$, 0.2mm) assumed, LEADCAP showed better compaction effects than Sasobit. CONCLUSIONS : The temperature $30^{\circ}C$ lower than general compaction temperatures can provide a better sensitivity for the evaluation of compaction effects. If a testing temperature and film thickness are grouped for the proper compaction conditions in the testing results, the compaction performance of each WMA additive can be more clearly discriminated in the grouped testing results matched with the grouped conditions.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.2
• /
• pp.67-84
• /
• 2005

This research was conducted to evaluate the effectiveness of reinforcement for nearly saturated soft clay compaction. The effectiveness was investigated by roller compaction test using nearly saturated clay specimens. The nearly saturated condition was obtained by submerging clay in the water for 12 hours. High water content specimens were compacted in plane strain condition by a steel roller. A specimen was compacted by four 5 cm horizontal layers. Specimens were prepared fur both reinforced and unreinforced cases to evaluate the effectiveness of reinforcement. Used reinforcement is a composite consisted of both woven and non-woven geotextile. The composite usually provides drainage and tensile reinforcement to hi인 water-contented clay so that it increases bearing capacity. Therefore, large compaction load can be applied to reinforced clay and it achieves higher density effectively. The reinforcement also increases compaction efficiency because it reduces the ratio between shear and vertical forces during compaction process. The maximum vertical stress on the base of specimen usually decreased with higher compaction thickness. The reinforcement increases soil stiffness under the compaction roller and it initiates stress concentration. As a result, it maintains higher vertical stress level on the base of specimen that provides better compaction characteristics. Based on test results, it can be concluded that the reinforcement is essential to achieve effective compaction on soft clay.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• v.y2004m10
• /
• pp.11-14
• /
• 2004

The object of this study is vibrating compaction and curing method in the production process of Design concrete for precast concrete(Design-PC) product. From change of vibrating compaction time and pre-curing time. curing temperature which would be factors of product quality in Design-PC concrete production. and research of optimized steam curing condition from relations between curing condition and strength development. basic data of vibrating compaction time and concrete steam curing method for Design-PC will be presented.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.03a
• /
• pp.357-364
• /
• 2002

This paper describes the feasibility of compacting subgrade layer in thicker lifts than currently permitted as 20 cm. This project involved constructing and testing a full scale test section in highway. Soil stiffness in field was evaluated by a nondestructive testing method, called Geogage. Quality control tests and FE Analysis were also conducted. Typical dynamic compaction roller of 11ton weight is applied for full scale test and a Mohr-Coulomb model and Plane strain condition are used for FE Analysis. The results showed that compaction-induced stress and dissipated energy are mainly depend on depth of soil and it could be possible to increase thickness of a lift.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.31 no.1
• /
• pp.82-95
• /
• 1989

This study was carried out for the stability analysis of earth dam by the variation of compaction density. The test samples were taken from five kinds of soil used for banking material and the degree of compaction for this samples were chosen 100, 95, 90, 85, and 80 percent. The stability problems were analysed by the settlement and camber( extra banking) of dam, strength parameter and dam slope, and coefficient of permeability and seapage flow through dam body. The results of the stability analysis of earth dam are as follows. 1. The more the fine particle increases and lower the compaction degree becomes, the lower the preconsolidation load becomes but the compression index becomes higher. 2. Sixty to eighty percent of settlement of dam occurs during the construction period and the settlement ratio after completion of dam is inversly proportional to the degree of compaction. 3. The camber of dam has heigher value in condition that it has more fine particle(N) and heigher dam height(H) with the relation of H= e(aN-bH-e). 4. The cohesion(C) decreases in proportion to compaction degree(D) and fine particle(N) with the relation of C= aD+ bN-c, but the internal friction angle is almost constant regardless of change of degree of compaction. 5. In fine soil, strength parameter from triaxial compression test is smaller than that from direct shear test but, they are almost same in coarse soil regardless of the test method. 6. The safety factor of the dam slope generally decreases in proportion to cohesion and degree of compaction but, in case of coarse soil, it is less related to the degree of compaction and is mainly afected by internal friction angle. 7. Soil permeability(K) decreases by the increases of the degree of compaction and fine particle with relation of K=e(a-bl)-cN) 8. The more compaction thickness is, the less vertical permeability (Kv) is but the more h6rzontal permeability (KH) is, and ratio of Kv versus KH is largest in range from 85 to 90 percent of degree of corn paction. 9. With the compaction more than 85 percent and coefficient of permeability less than ${\alpha}$X 10-$^3$cm/sec, the earth dam is generally safe from the piping action.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.11a
• /
• pp.289-292
• /
• 2003

CFRD face slab concrete has a much capability to occur crack due to drying shrinkage and vibrator compaction etc. Because crack of concrete induces structural problem and decrease durability of concrete, it is need to reduce crack of concrete. In the experimental study it was analyzed that the effect of curing of concrete and compaction on CFRD face slab concrete. As a results, it was found that control of construction condition into curing of concrete and compaction improved on construction efficiency of face slab concrete.

• Transactions of Materials Processing
• /
• v.7 no.2
• /
• pp.114-126
• /
• 1998

A plasticity theory applicable to the powdered metal compaction is briefly summarized and its varia-tional form for the finite element analysis is described. The compaction processes of axisymmetric solid cylinder are simulated. For the analysis of the friction effect on compaction process the investigations were performed for different compact geometries. Efforts are focused on the transmitted pressure through the compact and density distributions within the compacts. Numerical results show that :(1) the friction coefficient could be selected simply from the transmitted force data by the single acting compaction test and the simulated results ; and (2) density variations within the compacts rely on the compact geometry such as height to diameter ration and the frictional condition between compact and dies.

• Journal of the Korean Ceramic Society
• /
• v.43 no.12 s.295
• /
• pp.859-864
• /
• 2006

For the pressure compaction process of the ceramic powder, the green density is very different with both the ceramic body shape and the processing conditions. The density difference cause non-uniform shrinkages and deformations, and make cracks in the sintered ceramics. In this paper, Material properties of the alumina powder mixed with binder and the friction coefficient between the powder and the tool set were determined through the simple compaction experiments: Also the powder flow characteristics were simulated and the green density was analyzed during the powder compaction process with Finite Element Method (FEM). The results show that the density distributions of the green body were improved at the optimized processing condition and both the possibility of the farming crack generation and rho deformation of the sintered Alumina body were reduced.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.6
• /
• pp.163-171
• /
• 2001

It is important to pay careful attention to the backfill construction for the structural integrity of concrete box culvert. To increase the structural integrity of culvert good compaction by the dynamic compaction roller with big capacity is as effective as good backfill materials. However structural distress of the culvert could be occurred due to the excessive earth pressure by great dynamic compaction load. In this study, two box culverts were constructed with change compaction materials and construction methods. Two type of on-site soils such as subbase and subgrade materials were used as backfill materials. In most case, dynamic compaction rollers with 11 to 12 ton weights were used and vibration frequency were applied from 2000 to 2500 rpm for the great compaction energy. Backfill compactions with good quality soils were carried out to examine the effect of cushions on dynamic lateral soil pressure. Expanded polystyrene (EPS) and rubber of tire were adapted as cushion materials and they are set on the culverts before backfill construction. This paper presents the main results on the characteristics of dynamic earth pressures. Test result indicates that the amounts of increased dynamic pressures are affected with backfill materials, depth of pressure cell, and compaction condition. The earth pressure during compaction can give harmful effect to box culvert because the value of dynamic earth pressure coefficient $(\DeltaK_{dyn}=\DeltaK\sigma_h\DeltaK\sigma_v)$ during compaction is greater than that of static condition. It was observed that cushion panels of EPS(t=10cm) and rubber(t=5cm) are effective to mitigate dynamic lateral pressure on the culverts.

• Asian Journal of Turfgrass Science
• /
• v.11 no.3
• /
• pp.205-210
• /
• 1997

The metal spikes evaluated in this study significantly affected more negative on the turf wear and ball speed of putting green than alternative plastic spikes. 1.The metal spikes caused the most amount of wear compared with plastic spikes, athletic shoes and mountain-climbing shoes. On the other hand, athletic shoes caused the least amount of wear. Plastic spikes caused wear more than athletic shoes, hut apparently wear less than metal spikes. The wear from metal spike repaired later than any other tread types. 2.The wear from all kinds of shoe treads in wetcondition green were higher than in dry-condition green and the wear from metal spikes was more severe compared with plastic spikes in both green condition. 3. Ball speed of heavy compaction area by metal spike was reduced about 9% compared with that of light compaction area, hecause metal spikes made many holes in the putting green surface. On the other hand, plastic spikes did not affect hall speed of heavy and light compaction area in the putting green. Key words: Metal spike, Plastic spike, Wear, Ball speed.