• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1636-1638
• /
• 1994

Salt deposited on the surface of insulators used in electric power system causes flash-over accidents. Therefore, the quantity of salt on insulators should be monitored not to exceed a critical value. We propose a new remote sensing technique to measure the quantity of salt on insulators of power systems. A pulsed laser beam is focussed on ah insulator to dissociate the salt to sodium atoms. The amount of the salt is measured from the intensity of the spontaneous mission from the sodium atoms. In this paper, a compact salt meter composed of pulsed Nd:YAG laser and omission signal detection system will be introduced. And measurement condition such as the sensitivity, detection range, required laser fluence will be investigated.

• Journal of the Korean Society of Safety
• /
• v.9 no.1
• /
• pp.9-18
• /
• 1994

In this study, we conducted experimental tests to evaluate fracture behaviors of fresh-butt welded metal by Acoustic Emission technique. We selected similar welding and dissimilar welding process, the one welded for SM45C, SS41 and SUS304 of each material, the other for SM45C and SS41, SM45C and SUS304 and SS41 and SUS304. The fracturing processes of weld metal were estimatied through the fracture toughness test with compact tension specimens and fractography analysis. In ASTM test method E-399, type I curves for materials of this study were obtained by load-cod diagram of fracture toughness test. and 5% offset load( $P_{5}$) was estimated as the estimated crack initial load( $P_{Q}$), The estimated crack initial load( $P_{Q}$) of similar welding materials generally lower than base matal, and then SM45C appeared greatly in decreasing rate of PB, SS41 and SUS304 appeared in order. $P_{Q}$ of dissimilar welding materials were lower than the similar welding materials. $P_{Q}$ of welding of SM45C and SS41 appeared in small, SUS304 and SS41 appeared greatly in dissimilar welding materials. In fracture toughness test, AE counts increased before the inflection point of the slope, decreased after that. It was found that increasing of AE counts were due to the microcrack formation at the crack tip near the $P_{5}$ point through AE data. For welding materials in this study, both low and high AE amplitude appeared simulataneously. It was confirmed that the low AE amplotude was due to formation of micro void, micro crack or micro dimple, the high AE amplitude was caused by microvoid coalescence and quasi-cleavage fracture through analyses of fractograpy.apy.apy.apy.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.7
• /
• pp.293-300
• /
• 2016

Traditional databases exploit a record-based model, where the attributes of a record are placed contiguously in a slow hard disk to achieve high performance. On the other hand, for read-intensive data analysis systems, the column-based compressed database has become a proper model because of its superior read performance. Currently, flash memory SSD is largely recognized as the preferred storage media for high-speed analysis systems. This paper introduces a compressed column-storage model and proposes a new index and its data management scheme for a high-capacity data warehouse system. The proposed index management scheme is based on the asymmetric index duplication and achieves superior search performance using the master index and compact index, particularly for large read-mostly databases. In addition, the data management scheme contributes to the read performance and high reliability by compressing the related columns and replicating them in two mirrored SSD. Based on the results of the performance evaluation under the high workload conditions, the data management scheme outperforms the traditional scheme in terms of the search throughput and response time.

• Convergence Security Journal
• /
• v.9 no.2
• /
• pp.79-84
• /
• 2009

Recently, Move Picture Files have the same file format and a compression technique as Window Media Video form. but Moving Pictures using file format and a compression technique have question about Motion blur and compressibility. In this paper, we design and Implement for new Move Picture Solution EZ-MOV using FLV different from developed FLV(Flash Video) in the Macromedia company. EZ-MOV have advantages as follow. first, FLV player is able to compact disk access time and DRM (Digital Rights Management) with a built-in self and unable to an illegal video recording, second, whenever WMV formal file encoded FLV are able to lossless compression to fifty percent, third, FLV is able to Moving Picture streaming no buffering. fourth, FLV file is able streaming service no streaming server. fifth, FLV file is able to streaming service keep pace with download and streaming. sixth, FLV file is able to full duplex service.

• Journal of the Korean Society of Safety
• /
• v.7 no.1
• /
• pp.65-72
• /
• 1992

Objective of this research is to evaluate fracture behaviors of fresh-butt welded metal by the acoustic emission technique. The specimens used are medium carbon steel(SM45C), mild steel (SS41) and stainless steel(SUS304), which have different weldability. The similar welding and dissimilar welding processes are considered, in the former SM45C, SS41 and SUS304 are used, in the later the following metals are used SM45C and SS41, SM45C and SUS304 and SS41 and SUS304. The characteristics of fracture in weld metal are eshmated by the tension test with nominal speciemns, the fracture toughness test with compact tension specimens and fractography analysis. The results of tension test show for base metals and similar welding materials that the yield strength and ultimate strength of similar welding materials are increased, the elongation of those are decreased. The weldability of SUS304 is better than that of SM45C and SS41 In similar welding materials. Mechanical properties of dissimilar welding mateiiths we lower than those of similar welding materials. In dissimilar welding materials, the weldability of SM45C and SUS304 is better than that of SM45C and SS41, and also weidability of SS41 and SUS304 is better than SS41 and SM45C. Comparing mechanical properties with AE counts, it is found that AE conuts appeared on a small before the limit load of elasticity(P$_{e}$), and apper greatly near yield strength region in tension test. These results could contribute to the safety analyses and the evaluation of strength for welding structure.e.

• Journal of the Korean Vacuum Society
• /
• v.7 no.s1
• /
• pp.20-24
• /
• 1998

Photploymer films are widely used in printing and electronic industries, and their usage is expanding to encompass holography, data storage and data processing, optical waveguides and compact disks, etc. One of widely used photoplymerization initiator, 20chloro-hexaarylbiimidazole (o-Cl-HABI), is studied by laser flash photolysis in dichloromethane solution in the absence and presence of the visible light photosensitizing dye, 2, 5-bis[(2, 3, 6, 7 -tetrahydro- 1H, 5H -benzo [i, j,] quinolizin -1-yl) methylene]-cyclopenta-none, (JAW). In the presence of JAW, an increase in triarylimidazolyl radicals L.formation is observed in relative to the absence of JAW. The mechanism of this photosensitizing dissociation is concluded as the dissociation of the o-Cl-HABI radical anion formed by the electron transfer from excited singlet state of JAW to o-Cl-HABI. The observed formation of L.radicals exhibits a linear dependence on o-Cl-HABI concentration. The rate constant of electron transfer obtained from this dependence is equal to (1.0$\pm$0.2) x $10^9 M^{-1}s^{-1}$. No reaction between the excited triplet state of JAW and o-Cl-HABI is found.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.474-478
• /
• 2006

It is becoming more significant to develop a rotary voice coil motor(VCM) type's actuator for small form factor (SFF) optical disk drive(ODD), as portables are getting more and more popularized nowadays. The actuator which is applicable to small-sized ODD with a compact flash(CF) II card size was developed and fabricated. The experimental results showed that the finite element(FE) model is different from the fabricated model. And so flexible mode frequencies did not satisfy specifications of small-sized ODD, and tuning. Tuning procedures were required to improve dynamic characteristics of the fabricated actuator through finite difference method(FDM). At first, design variables were extracted through parameter study and the tuned FE model was improved by design of experiment(DOE). Consequently, It was confirmed that the improved model was applicable to SFF ODD.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.193-197
• /
• 2002

In this study, the casting/forging process was applied to the Shift-Fork, a manual transmission part of automobiles. In the casting experiments, the effects of additives, Sr, Ti＋B and Mg, on the mechanical properties and the microstructure of a cast preform were investigated. When 0.03% Sr were added into the molten aluminum alloy, the finest silicon-structure was observed in the cast preform and the highest tensile strength and elongation accomplished. And when 0.2% Ti＋B were added into the molten Al-Si alloy, the highest values of tensile strength were obtained. The maximum hardness was in case of 0.2% Mg. In the forging experiment, it was confirmed that the optimal configuration of the cast preform could be predicted by FE analysis. To minimize the cost as the press size, the compact shape of preform was proposed to reduce the volume of flash. The modification of shape in designing preform was performed to attain a satisfactory performance in the areas where the mechanical strength were more required. By using FVM(Finite Volume Method) software, it was verified that a proposed casting design was available. To identify the relationship between effective strain and mechanical properties of the final forged product, the compression test was performed. As the result, the tensile strength and elongation of a cast preform were much higher than before forging. The minimum forging temperature was found 40$0^{\circ}C$ to save heating time.

• Journal of ILASS-Korea
• /
• v.28 no.1
• /
• pp.32-42
• /
• 2023

In this study, spray characteristics of n-heptane and propane were investigated under different injection pressure using various imaging techniques such as Mie-scattering, DBI (diffuse back-illumination), and Schlieren imaging techniques. NI compact RIO system was used to control a test injector. Spray penetration length, length-to-width ratio and number of black pixels were calculated by using MATLAB software to compare spray characteristics of each fuel. Longer spray penetration length and higher length-to-width ratio were observed in propane spray because of flash boiling caused by high saturated vapor pressure. Spray collapse occurred in propane spray due to the high plume-to-plume interaction. Moreover, rapid evaporation occurred in propane spray, so that nozzle tip wetting could not be observed. Rapid evaporation of propane also caused fewer residual droplets compared to n-heptane spray. Therefore, propane is advantageous in reducing the generation of soot emission from large droplets that are not atomized. However, additional evaluation should be conducted considering combustion efficiency and the possibility of deposits by nozzle tip icing during fuel injection.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.6
• /
• pp.2747-2753
• /
• 2011

In this paper, a PWM current-mode DC-DC boost converter for mobile phone flash application has been proposed. The converter which is operated with 5 Mhz high switching frequency is capable of reducing mounting area of passive devices such as inductor and capacitor, consequently is suitable for compact mobile phones. This boost converter consists of a power stage and a control block. Circuit elements of the power stage are inductor, output capacitor, MOS transistors and feedback resistors. Meanwhile, the control block consists of pulse width modulator, error amplifier, oscillator etc. Proposed boost converter has been designed and verified in a $0.5\;{\mu}m$ 1-poly 2-metal CMOS process technology. Simulation results show that the output voltage is 4.26 V in 3.7 V input voltage, output current 100 mA which is larger than 25 ~ 50 mA in conventional 500 Khz driven converter when the duty ratio is 0.15.