• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.385-385
• /
• 2012

A two terminal N+/P/N+ junction device to replace the conventional selective transistor was studied as a bilateral switching device for spin transfer torque (STT) MRAM based on 3D device simulation. An N+/P/N+ junction structure with $30{\times}30nm$ area requires bi-directional current flow enough to write a data by a drain induced barrier lowering (DIBL) under a reverse bias at N+/P (or P/N+ junction), and high current on/off ratio of 106. The SiGe materials are widely used in hetero-junction bipolar transistors, bipolar compensation metal-oxide semiconductors (BiCMOS) since the band gap of SiGe materials can be controlled by changing the fraction and the strain epilayers, and the drift mobility is increased with the increasing Ge content. In this work, N+/P/N+ SiGe material based junction provides that drive current is increased from 40 to $130{\mu}A$ by increased Ge content from 10~80%. When Ge content is about 20%, the drive current density of SiGe device substantially increased to 2~3 times better than Si-based junction device in case of 28 nm P length, which is sufficient current to operation of STT-MRAM.

• Journal of Information Technology Applications and Management
• /
• v.26 no.6
• /
• pp.103-117
• /
• 2019

Demand for high power motors is rapidly increasing as the 4th industry and convergence technology has recently emerged. In order to produce high-strength permanent magnets, the magnets used for magnetization have been increased from DC 300V in the 1970s to DC 2.5kV in the 2010s, Up to DC 10kV in the 2030s, It is expected that higher voltage will be used to magnetize. However, in the case of a magnetizer using an existing electric signal control device, it is necessary to use a control device with a high-voltage insulation function in case a high voltage used for magnetization is leaked to the control device. If a short circuit accident occurs, the controller must be shut down and serious problems such as excessive repair costs arise. In this study, a control system adopting optical communication method instead of electric signal control method is proposed to prevent leakage currents in high-voltage magnetizer. We design a transmitter(Tx) and a receiver(Rx) device for the optical communication control device and implemented a prototype connecting the optical cable. In order to demonstrate the utility of high-voltage magnetizer using the optical communication control device, we analyzed the initial cost and the yearly cost for the years to analyze the net present value. As a result, In the case of the low-voltage magnetizer, the electric signal control method cost less, As the operating voltage of the magnetizer becomes higher. It is confirmed that it takes less cost when the optical communication control device is used.

• International Journal of Computer Science & Network Security
• /
• v.24 no.2
• /
• pp.178-188
• /
• 2024

In the near future, it is expected that there will be billions of connected devices using fifth generation (5G) network services. The recently available base stations (BSs) need to mitigate their loads without changing and at the least monetary cost. The available spectrum resources are limited and need to be exploited in an efficient way to meet the ever-increasing demand for services. Device to Device communication (D2D) technology will likely help satisfy the rapidly increasing capacity and also effectively offload traffic from the BS by distributing the transmission between D2D users from one side and the cellular users and the BS from the other side. In this paper, we propose to apply D2D overlay communication with cognitive radio capability in 5G networks to exploit unused spectrum resources taking into account the dynamic spectrum access. The performance metrics; throughput and delay are formulated and analyzed for CSMA-based medium access control (MAC) protocol that utilizes a common control channel for device users to negotiate the data channel and address the contention between those users. Device users can exploit the cognitive radio to access the data channels concurrently in the common interference area. Estimating the achievable throughput and delay in D2D communication in 5G networks is not exploited in previous studies using cognitive radio with CSMA-based MAC protocol to address the contention. From performance analysis, applying cognitive radio capability in D2D communication and allocating a common control channel for device users effectively improve the total aggregated network throughput by more than 60% compared to the individual D2D throughput without adding harmful interference to cellular network users. This approach can also reduce the delay.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.13 no.3
• /
• pp.1311-1324
• /
• 2019

In the traditional cellular network communication, the cellular user and the base station exchange information through the uplink channel and downlink channel. Meanwhile, device-to-device (D2D) users access the cellular network by reusing the channel resources of the cellular users. However, when cellular user channel conditions are poor, not only D2D user cannot reuse its channel resources to access the network, but also cellular user's communication needs cannot be met. To solve this problem, we introduced a novelty D2D communication mechanism in the downlink, which D2D transmitter users as half-duplex (HD) relays to assist the downlink transmission of cellular users with reusing corresponding spectrum. The optimization goal of the system is to make the cellular users in the bad channel state meet the minimum transmission rate requirement and at the same time maximize the throughput of the D2D users. In addition, i for the purpose of improving the efficiency of relay transmission, we use two-antenna architecture of D2D relay to enable receive and transmit signals at the same time. Then we optimized power of base station and D2D relay separately with consideration of backhaul interference caused by two-antenna architectures. The simulation results show that the proposed HD relay strategyis superior to existing HD and full-duplex (FD) models in the aspects of system throughput and power efficiency.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.24 no.2
• /
• pp.204-210
• /
• 2021

In this paper, we studied a method of wirelessly checking up the POD for captive flight tests which is performed during the development of guided weapons systems. The wireless power transfer module, the power distribution device, and the battery pack were designed to wirelessly power the captive flight test POD, and the communication device was designed to enable wireless communication between the POD and the check-up device. The communication device was designed to enable WiFi, IR communication, and laser diode communication, so that various communication methods could be tested. Through the performance test, it was confirmed that power was stably supplied to the captive flight test POD, and the wireless communication performance was verified by measuring the delay time and error rate. As a result, by using our system the POD check-up for the captive flight test was performed wirelessly and the data of the captive equipment could be obtained effectively.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.13 no.1
• /
• pp.69-78
• /
• 2017

As the smartphone-based devices are diffused and developed rapidly, they provide the convenience to the users. The abovementioned sentence technologies are being used not only in the existing sensor and wireless network technology but also in the application services of the diverse fields application services such as smart appliance, smart car, smart health care, etc. and the new fusion paradigm from the industry is presented by undertaking the researches in diverse area by the enterprises and research institutions. However, the smart environment exposes its weaknesses in the mobile terminal area, existing wireless network and IT security area. In addition, due to new and variant ways of attack, not only the critical information are disclosed However also the financial damages occur. This paper proposed the protocol to perform the smartphone-based safe device monitoring and safe communication. The proposed protocol designed the management procedure of registration, identification, communication protocol and device update management protocol and the safety against the attack techniques such as the an-in-the-middle-attack, impersonation attack, credential threat, information leaks and privacy invasion was analyzed. It was observed that the proposed protocol showed the performance improved by approximately 52% in the communication process than the existing system.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39A no.3
• /
• pp.161-163
• /
• 2014

We consider the device-to-device (D2D) communication underlaying multi-cell interference system, in which the cellular downlink (DL) resource is reused by K cells and two D2D transmission links within each cell. In this paper, it has been shown that the downlink intra-cell and inter-cell interference can be effectively handled by interference alignment (IA) technique, as long as the simultaneous D2D links are properly selected or power-controlled so that they may not incur interference to the base stations in the same and neighbor cells. In particular, we provides the IA technique that can achieve the theoretically maximum possible degree of freedom (DOF), demonstrating that a total of (K+1)M degrees of freedom (DOFs) can be achieved for K-cell interference system with two underlaying D2D links, where base stations, cellular UE's, and D2D UE's all have M transmit and receive antennas.

• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.841-843
• /
• 2002

In this paper, we develop the remote control device of vending machine through internet. This device can control the temperature, humidity and on/off switch. This device is operated by the Java based TCP/IP control program.

• Proceedings of the Optical Society of Korea Conference
• /
• 2005.07a
• /
• pp.56-57
• /
• 2005

We have studied on the SLDs utilizing InAs chirped QD structure. The output power and spectral bandwidth are obtained as CW 40 mW at RT and about 100 nm, respectively. More high performance of SLD can be possible with optimized design for the chirped QD structures.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.15 no.3
• /
• pp.29-36
• /
• 2019

With the rapid development of 5G technology, more and more network functions are interconnected and more popular. In order to effectively manage emerging network concepts, it allows any device object in the real world to be connected anywhere and at any time through the integration of device object recognition, interaction and raw data collection technologies. In addition, IP Multimedia Subsystem (IMS) is an architecture framework for transmitting IP-based information to the device object which can be represented as end user. Therefore, the Internet of Things and IP Multimedia Subsystem (IoT-IMS) communication platform can provide a convenient and fast way for user or device objects to deploy new application services effectively. In particular, in order to collect and manage the device information from IoT effectively in the IoT-IMS communication platform, an IoT Information Gateway (IIG) is proposed. Through the IoT Application Service (AS) scenario, the collected device information can be easily observed and managed in a unified way.