• Journal of Power System Engineering
• /
• v.10 no.2
• /
• pp.5-10
• /
• 2006

Our environment is faced with serious problems related to the air pollution from automobiles in these days. In particular, the exhaust emissions of diesel engine are recognized main cause which influenced environment strong. In this study, the potential possibility of biodiesel fuel was investigated as an alternative fuel for a naturally aspirated common rail diesel engine. The smoke emission of biodiesel fuel 30vol-%(max. content) was reduced in comparison with diesel fuel, that is, it was reduced approximately 60% at 4000rpm, full load. But, power, torque and brake specific energy consumption didn't have no large differences. But, NOx emission of biodiesel fuel was increased compared with commercial diesel fuel.

• Journal of ILASS-Korea
• /
• v.9 no.1
• /
• pp.15-20
• /
• 2004

The post injection effect to enhance aftertreatment devices' performance is essential to meet future stringent emission standards by controlling exhaust gas temperature and emission pollutants. The test has been made with commercial common rail diesel engine by post injection manipulation, to optimize exhaust gas temperature while guarantee low fuel penalty. The optimization was done at 1500, 2000 and 2500[rpm] for 2, 4[bar] condition which show low exhaust gas temperature. The main purpose of this test is dedicated to understand mechanism of exhaust gas temperature rise while optimizing

• Journal of the Korean Society of Combustion
• /
• v.8 no.3
• /
• pp.31-37
• /
• 2003

The objective of this work is to investigate the effect of swirl, injection pressure and pilot injection on D.I.Diesel combustion by using a transparent engine system. The test engine is equipped with common rail injection system to obtain high pressure and to control injection timing and duration. In this study, the combustion analysis and steady flow test were conducted to estimate the heat release rate from in-cylinder pressure and pilot injection was investigated by using LII technique. As the results, high injection pressure was found to shorten ignition delay as well as enhance peak pressure and heat release rate was greatly affected by injection timing and pilot injection. In addition, the results showed that the period of soot formation corresponded to the diffusion flame.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.6
• /
• pp.9-15
• /
• 2004

The characteristics of combustion and emissions were investigated in a single cylinder DI diesel engine equipped with a common rail injection system. This study presents an experimental study of the effect of engine speed, injection timing, injection pressure and pilot injection timing on the combustion and exhaust emissions. The engine speeds were 1000 and 2000rpm and the corresponding injection pressures were 50 and 100MPa. Experimental results show that NOx emissions decrease with retarded injection timing, while HC and CO emissions increases. Higher injection pressure increases NOx with lower soot emissions. For the case with the pilot injection prior to main injection, the ignition delay is shortened and the premixed combustion ratio decreases. Also NOx and soot emissions are decreased with increase of pilot injection advance.

• International Journal of Automotive Technology
• /
• v.8 no.2
• /
• pp.155-163
• /
• 2007

The control of the fuel to be introduced into the combustion chamber under idling and low-load conditions is known to be a problem in Diesel engines, owing to the relatively small fraction of the full-load fuel needed under light loads. Thus, particular attention should be paid to the behavior of the injector with reference to short injection events. This work presents the results of an experimental campaign carried out with two different types of common rail injectors, a standard injector and a modified one. The latter, coming from a simple modification realized in a standard injector, exhibits linear behavior between injected fuel and solenoid energizing time in the field of short injections. A direct comparison of the two injection behaviors suggests a possible way to better control short or pilot injections.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.567-570
• /
• 2002

The LVDS (Low Voltage Differential Signaling) I/O cells, fully compatible with ANSI TIA/ EIA-644 LVDS standard, are designed using a 0.35${\mu}m$ standard CMOS technology. With a single 3V supply, the core cells operate at 1.34Gbps and power consumption of the output driver and the input receiver is 10. 5mW and 4.2mW, respectively. In the output driver, we employ the DCMFB (Dynamic Common-Mode FeedBack) circuit which can control the DC offset voltage of differential output signals. The SPICE simulation result of the proposed output driver shows that the variation of the DC offset voltage is 15.6% within a permissible range. In the input receiver, the proposed dual input stage with a positive feedback latch covers rail-to-rail input common-mode range and enables a high-speed, low-power operation. 5-channels of the proposed LVDS I/O pair can handle display data up to 8-bit gray scale and UXGA resolution.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.6
• /
• pp.107-116
• /
• 2012

In this study, the trucks(2.9-liter) have been developed to use DME as fuel, and performance test of the vehicle's DME engine, power, emissions, fuel economy and vehicle aspects was conducted. For experiments, the fuel system(common-rail injectors and high-pressure pump included) and the engine control logic was developed, and ECU mapping was performed. As a result, the rail pressure from 40MPa to approximately 65% increase compared to the base injector has been confirmed that. Also, the pump discharge flow is 15.5 kg/h when the fuel rail pressure is 400rpm(40MPa), and the pump discharge flow is 92.1 kg/h when the fuel rail pressure is 2,000rpm(40MPa). The maximum value of full-load torque capability is 25.5 kgfm(based on 2,000 rpm), and more than 90% compared to the level of the diesel engine were obtained. The DME vehicle was developed in this study, 120 km/h can drive to the stable, and calculated in accordance with the carbon-balance method of fuel consumptions is 5.7 km/L.

• Journal of Institute of Convergence Technology
• /
• v.2 no.1
• /
• pp.24-30
• /
• 2012

In this study, the trucks(2.9-liter) have been developed to use DME as fuel, and performance test of the vehicle's DME engine, power, emissions, fuel economy and vehicle aspects was conducted. For experiments, the fuel system(common-rail injectors and high-pressure pump included) and the engine control logic was developed, and ECU mapping was performed. As a result, the rail pressure from 40MPa to approximately 65% increase compared to the base injector has been confirmed that. Also, the pump discharge flow is 15.5 kg/h when the fuel rail pressure is 400rpm(40 MPa), and the pump discharge flow is 92.1 kg/h when the fuel rail pressure is 2,000rpm(40MPa). The maximum value of full-load torque capability is 25.5kgfm(based on 2,000rpm), and more than 90% compared to the level of the diesel engine were obtained. The DME vehicle was developed in this study, 120 km/h can drive to the stable, and calculated in accordance with the carbon-balance method of fuel consumptions is 5.7 km/L.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.35C no.2
• /
• pp.22-28
• /
• 1998

A $g_m$-control technique using a new electronic zener diode (EZD) for CMOS rail-torail input stages is presented. A regulated CMOS inverter is used as an EZD to obtain a constant-$g_m$ input stage. The turn-off characteristic of the proposed EZD is better than that of the existing EZD using two complementarey diodes, and thus, better $g_m$-control can be achieved. With this input stage, a 3V constant-$g_m$ rail-to-rail CMOS op-amp has been designed and fabricated using a $0.8\mu\extrm{m}$single-poly, double-metal CMOS process. Measurements results show that the $g_m$ variation is about 6% over the entire input common-mode range, and the op-amp has a dc gain of 88dB and a unity-gain frequency of 4MHz for $C_L=20pF, R_L=10k\Omega$

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.4
• /
• pp.69-76
• /
• 2001

VCO nozzle is devised to minimize the HC emission and has been applied on some HSDI diesel engines. But it is not well reported whether VCO nozzle would be advantageous over SAC nozzle in a small HSDI diesel engine. In this paper it is presented that characteristics of VCO and SAC nozzle under common rail fuel injection system and their effects on the performance in a small HSDI diesel engine.