• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.1
• /
• pp.277-283
• /
• 2020

In a concentric magnetic gear, which replaces the teeth of a mechanical gear with a permanent magnet, the polar ratio of the magnet that determines the reduction ratio affects the behavior of the magnetic gear dramatically. This study analyzed the density of transmission torque, the efficiency of torque considering the solid loss, and the torque quality, including the cogging characteristics using finite element analysis. When the pole number on the driving side was changed from two to five, it was confirmed that there was an optimal pole ratio, in which the transmission torque was maximized. Because eddy current generation density is proportional to the magnetic field, the transmission efficiency also shows a similar tendency to the transmission torque density, and the efficiency is more than 95% at a low gear ratio. The cogging characteristics due to the interaction of the permanent magnets with the limited number of poles are inversely proportional to the least common multiple between the number of magnets on the drive side and the number of modulator teeth. A test model was built for the transmission torque evaluation.

• Wind and Structures
• /
• v.18 no.2
• /
• pp.181-194
• /
• 2014

A major problem with high-mast light poles is the effects that wind vortex shedding can have on the pole itself because of the lock-in phenomenon. It is desired that the coefficients in the AASHTO Standard Specifications ($5^{th}$ edition) for Structural Supports for Highway Signs, Luminaries, and Traffic Signals be analyzed and refined. This is for the belief that the span of the shapes of poles for which the coefficients are used is much too broad and a specific coefficient for each different shape is desired. The primary objective of this study is to develop wind vortex shedding coefficient for a multisided shape. To do that, an octagonal shape was used as the main focus since octagonal cross sectioned high-mast light poles are one of the most common shapes in service. For the needed data, many wind parameters, such as the static drag coefficient, the slope of aerodynamic lift coefficient, Strouhal number, the lock-in range of wind velocities producing vibrations, and variation of amplitude of vortex-induced vibration with Scruton number are needed. From wind tunnel experiments, aerodynamic parameters were obtained for an octagonal shape structure. Even though aerodynamic coefficients are known from past test results, they need to be refined by conducting further wind tunnel tests.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.7 no.3
• /
• pp.72-80
• /
• 1997

A new design method for Takagi-Sugeno (T-S in short) fuzzy controller which guarantees global asymptotic stability and satisfies a desired performance is proposed in this paper. The method uses LMI(Linear Matrix Inequality) approach to find the common symmetric positive definite matrix P and feedback fains K/sub i/, i= 1, 2,..., r, numerically. The LMIs for stability criterion which treats P and K'/sub i/s as matrix variables is derived from Wang et al.'s stability criterion. Wang et al.'s stability criterion is nonlinear MIs since P and K'/sub i/s are coupled together. The desired performance is represented as $ LMIs which place the closed-loop poles of $ local subsystems within the desired region in s-plane. By solving the stability LMIs and pole placement constraint LMIs simultaneously, the feedback gains K'/sub i/s which gurarntee global asymptotic stability and satisfy the desired performance are determined. The design method is verified by designing a T-S fuzzy controller for an inverted pendulum with a cart using the proposed method.

• Smart Structures and Systems
• /
• v.8 no.2
• /
• pp.205-217
• /
• 2011

This article describes the research work involving the implementation of an Active Bracing System aimed at the modification of the initial dynamics of a laboratorial building structure to a new desired dynamics. By means of an adequate control force it is possible to assign an entirely new dynamics to a system by moving its natural frequencies and damping ratios to different values with the purpose of achieving a better overall structural response to external loads. In Civil Engineering applications, the most common procedures for controlling vibrations in structures include changing natural frequencies in order to avoid resonance phenomena and increasing the damping ratios of the critical vibration modes. In this study, the actual implementation of an active system is demonstrated, which is able to perform such modifications in a wide frequency range; to this end, a plane frame physical model with 4 degrees-of-freedom is used. The Active Bracing System developed is actuated by a linear motor controlled by an algorithm based on pole assignment strategy. The efficiency of this control system is verified experimentally by analyzing the control effect obtained with the modification of the initial dynamic parameters of the plane frame and observing the subsequent structural response.

• Proceedings of the KIEE Conference
• /
• 1999.07g
• /
• pp.3271-3273
• /
• 1999

In this paper, new micromachined tunable bandpass filters for multi-band millimeter-wave telecommunication systems are proposed. Two types of mm-wave tunable filters are fabricated using micromachining technology and the responses of the filters are measured. One is two-pole lumped elements filter and the other two-pole resonators filter. Frequency tunability of the filter is achieved by changing the gap between a common CPW ground plate and the movable cantilever beam connected to the transmission line with the controllable range of 2.5 ${\mu}m$. The deflection of cantilever beam is measured with the applied DC voltage. With the applied bias voltage from 0 to 50 V, the fabricated filters show 0.6 GHz(2.3 %) at 26.6 GHz, and 0.8 GHz(2.5%) at 32 GHz center frequency shift for the lumped elements and resonators filter, respectively.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.1
• /
• pp.167-174
• /
• 2016

The Korean distribution line currently consists of overhead ground wires (OHGW), overhead distribution lines, neutral wires (NW), and messenger wires (MW). The MW is installed under the NW. The lightning protection system in Korea is focused on OHGW and lightning arrester and the MW are not considered. Therefore, this paper proposes the applicability of MW for purpose of lightning protection. For this, we analyzed the effects of lightning overvoltage according to the existence of OHGW and MW and the grounding conditions of the MW in the Korean distribution system. The grounding conditions of the MW that we took into consideration were the common or separate grounding of the MW and NW. The analysis based on the equivalent circuit of the distribution pole at each condition was performed. The distribution lines and lightning were modeled using the Electromagnetic Transients Program (EMTP). For each of the installation conditions of the OHGW and MW, the various lightning conditions were simulated and analyzed for both direct and indirect lightning. The simulation results showed that, if the OHGW was not installed in the Korean distribution system, the lightning overvoltage could be reduced by the common grounding of the MW and NW.

• Journal of Magnetics
• /
• v.21 no.3
• /
• pp.356-363
• /
• 2016

To improve the sensing accuracy of the newly developed magnetically suspended sensitive gyroscope (MSSG), it is necessary to analyze the causes of drift error. This paper build the models of disturbing torques generated by stator assembly errors based on the geometric construction of the MSSG with double spherical envelope surfaces, and further reveals the generation mechanism of the drift error. Then the drift error from a single stator magnetic pole is calculated quantitatively with the established model, and the key factors producing the drift error are further discussed. It is proposed that the main approaches in reducing the drift error are guaranteeing the rotor envelope surface to be an ideal spherical and improving the controlling precision of rotor displacement. The common problems associated in a gyroscope with a spherical rotor can be effectively resolved by the proposed method.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.8
• /
• pp.1644-1650
• /
• 2009

An improved guarding circuit is applied to a transconductance driven-right-leg circuit to decrease common-mode current at measurement electrodes due to power-line interference. After showing conventional guarding circuit is instable due to gain-peaking when used with a transconductance DRL circuit, the effect of the proposed guarding circuit modified to suppress the gain-peaking by inserting a series resistor between shields and a shield driver was analyzed. It is shown that, besides stability, the proposed guarding circuit provides two other advantages: 1) The gain of the shield driver can be set to be unit nominally. 2) The loop gain of the transconductance DRL loop can be increased due to pole-zero canceling. The proposed circuit was implemented and the advantages were confirmed.

• Proceedings of the KIEE Conference
• /
• 2007.11c
• /
• pp.165-169
• /
• 2007

Organic EL has been expected to adopt to a new styles of technology that make flat display after Tang & Vanslyke made food electric luminescence device in late 1980s. Their studies based on multi layer structure that consists of emitting layer and carrier transporting layer using proper organic material. In this study we made multi layer device using $Eu(TTA)_3(phen)$ as a luminescence material by PVD and investigate luminous properties of each device. But oxidization of organic layer by ITO, energy walls in both pole interface, contaminations of ITO surface, importance of protecting membrane, diffusive dimming of light to cathode organic layer, these causes of degradations are common facts of a macromolecule and micromolecule. We think these degradation caused by the impact of heat and electro-chemical factor, bulk effect and interface phenomenon, and raise a question.

• Proceedings of the KIPE Conference
• /
• 2004.07a
• /
• pp.219-223
• /
• 2004

Since rotor position information is necessary to drive the SRM, absolute-encoder, resolver and incremental encoder is used to detect a rotor position. But, it is not desirable to use a high price encoder and microprocessor under the condition of the simple driving system when precision control is not demanded. In this paper, only using the reflective type two photo-sensors replaces the conventional opto-interrupter and slotted-disk, which not only remove a slotted-disk section but drive three-phase 6/4 pole SRM bidirectionally, Therefore, control circuit can compose common analog device with low price.