• Structural Engineering and Mechanics
• /
• v.36 no.6
• /
• pp.745-758
• /
• 2010

12 typical laminated composite reinforced concrete (RC) walls with different concrete ages and 3 cast-in-place RC walls subjected to low frequency cyclic load were carried out in this study. The failure mode, force-deformation response and energy dissipation capacity of these specimens were investigated. Differences of structural behaviours between composite RC walls and common cast-in-place RC walls were emphasized in the analysis. The compatibility of the composite specimens with different concrete ages was discussed based on the experiment. Test results indicated that the differences between the lateral bearing capacity and the displacement ductility of the composite walls and the common walls were not so obvious. Some of the composite specimen even has higher bearing capacity under the experiment loading situation. Besides, the two parts of the laminated composite specimens demonstrates incompatibility at the later loading sequence on failure mode and strain response when it is in tension. Finally, this laminated composite shear walls are suggested to be applied in rapid reconstruction structures which is not very high.

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1488-1489
• /
• 2006

Gas Discharge Tubes (GDTs) are widely used as surge protectors for communication applications due to their small internal capacitance. In these days, however, they are mostly used in combined configurations, because the activation voltage required to initiate the discharge process in the GDTs for sufficient amount of time can be large enough to damage surge-sensitive protected circuits. For GDTs with a considerably high initial over-voltage value, we should limit the peak voltage using a TVS or filter. As for ZnO varistors, even though their performance for voltage restriction is excellent their applications in high-frequency communication circuits have been limited because of higher internal capacitance when compared to the GDTs. In order to develop a surge protector for communication applications by taking advantages of these two devices, we built a combination circuit that connects a GDT and a ZnO varistor along with a choke coil in common and differential modes. We describe how the applied SPDs operate in protection process steps with the actual data obtained from the residual voltage measurements at each step. The experiment results show that the surge voltage restriction with the choke coil is more effective in differential mode than in common mode.

• Journal of Power Electronics
• /
• v.18 no.1
• /
• pp.81-91
• /
• 2018

This paper proposes a double line voltage synthesis (DLVS) strategy for three-to-five phase direct matrix converters. In the proposed strategy, the input and expected output voltages are divided into 6 segments and 10 segments, respectively. In addition, in order to obtain the maximum voltage transfer ratio (VTR), the input line voltages and "source key" should be selected reasonably according to different combinations of input and output segments. Then, the corresponding duty ratios are calculated to determine the switch sequences in different segment combinations. The output voltages and currents are still sinusoidal and symmetrical with little lower order harmonics under unbalanced or distorted input voltages by using this strategy. In addition, the common mode voltage (CMV) can be suppressed by rearranging some of the switching states. This strategy is analyzed and studied by a simulation model established in MATLAB/Simulink and an experimental platform, which is controlled by a DSP and FPGA. Simulation and experimental results verify the feasibility and validity of the proposed DLVS strategy.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39B no.5
• /
• pp.251-259
• /
• 2014

In this paper, we propose Low Energy Service Discovery (LESD) protocol for common discovery mode of IEEE 802.15.8 Peer Aware Communications (PAC). In order to minimize power consumption, Basic Repetition Block (BRB) is defined. Device is able to select operating mode and synchronize other devices through it. Proposed MAC procedure is Carrier Sense Multiple Access with Collision Avoidance (CSMA/CA) based on overhearing technique. Even if device has not been received response signal since transmitted request signal, it is able to discover other devices of same group through the overhearing technique. IEEE 802.15.8 PAC has required that performances of common discovery mode are presented about discovered devices during the simulation time, discovery latency and average power consumption. By considering the number of devices per group and channel environment, two scenarios are evaluated through system level simulation and the simulation results of proposed scheme are compared with CSMA/CA in same simulation conditions. As a result, proposed scheme is able to get high energy efficiency of devices as well as increase the number of discovered devices during simulation time when the longer the number of devices is distributed over a limited area.

• Structural Engineering and Mechanics
• /
• v.53 no.4
• /
• pp.767-780
• /
• 2015

Delaminations and cracks are common failures in structures. They may significantly reduce the stiffness of the structure and affect their vibration characteristics. In the present study, an analytical solution is developed to study the effect of an edge crack on the vibration characteristics of delaminated beams. The rotational spring model, the 'free mode' and 'constrained mode' assumptions in delamination vibration are adopted. This is the first study on how an edge crack affects the vibration characteristic of delaminated beams and new nondimensional parameters are developed accordingly. The crack may occur inside or outside the delaminated area and both cases are studied. Results show that the effect of delamination length and thickness-wise location on reducing the natural frequencies is aggravated by an increasing crack depth. The location of the crack also influences the effect of delamination, but such influence is different between crack occurring inside and outside the delaminated area. The difference of natural frequencies between 'free mode' and 'constrained mode' increases then decreases as the crack moves from one side of the delaminated region to the other side, peaking at the middle. The analytical results of this study can serve as the benchmark for FEM and other numerical solutions.

• The Journal of Bigdata
• /
• v.1 no.2
• /
• pp.45-63
• /
• 2016

According to changes of recent climate social structures, frequency of occurrence new or complex disasters are increasing. So the importance of disaster prevention is increasing. To provide useful information of disaster prevention activities, We use the "Safety Sinmungo" main processing practices included Facility safety management in Ministry of Public Safety and Security. Facility safety management is the most and common disaster prevention activities. We identified the keywords in the risk report and facilities to residents report and analyzed the seasonal and inter-regional facilities report distribution process. We also utilized social network analysis techniques to configure a 1-mode, 2-mode facilities around the keyword for differences.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1120-1124
• /
• 2005

We reviewed controllers with a time delay estimation in this paper. Time delay control (TDC) and sliding mode control (SMC) are well known robust control schemes. Basically, the TDC has a main characteristic called a time delay estimation from which we can estimate the total uncertainty of a system. . The TDC causes the stick-slip in the case of systems with a friction. The so-called TDCSA which are short for TDC with switching action was developed to reduce the stick-slip. The TDC has the additional switching action term in the TDC structure. In the other hand, the SMC dose not have a time delay estimation but instead it can estimate the system uncertainty through the switching action. The SMC has a difficulty to estimate the total uncertainty of a system because it does not have a time delay estimation. In order to solve the difficulty, some control schemes were developed. Among them, we need to focus our attention on two control schemes: SMCPE and SMCTE, which are short for sliding mode control with a perturbation estimation and sliding mode control with a time delay estimation, respectively. In this paper, we analyzed and compared the characteristic of above three controllers. Even though the motives for the development of three control schemes are different, three control schemes have much in common in terms of their controller structures.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.5
• /
• pp.675-681
• /
• 2016

A 41dB gain control range $6^{th}$-order band-pass receiver front-end (RFE) using CMOS switched frequency translated impedance (FTI) is presented in a 40 nm CMOS technology. The RFE consists of a frequency tunable RF band-pass filter (BPF), IQ gm cells, and IQ TIAs. The RF BPF has wide gain control range preserving constant filter Q and pass band flatness due to proposed pre-distortion scheme. Also, the RF filter using CMOS switches in FTI blocks shows low clock leakage to signal nodes, and results in low common mode noise and stable operation. The baseband IQ signals are generated by combining baseband Gm cells which receives 8-phase signal outputs down-converted at last stage of FTIs in the RF BPF. The measured results of the RFE show 36.4 dB gain and 6.3 dB NF at maximum gain mode. The pass-band IIP3 and out-band IIP3@20 MHz offset are -10 dBm and +12.6 dBm at maximum gain mode, and +14 dBm and +20.5 dBm at minimum gain mode, respectively. With a 1.2 V power supply, the current consumption of the overall RFE is 40 mA at 500 MHz carrier frequency.

• Journal of Navigation and Port Research
• /
• v.42 no.2
• /
• pp.87-96
• /
• 2018

A trajectory control system plays an important role in controlling motions of marine vehicle when a series of way points or a path is given. In this paper, a sliding mode control (SMC)-based trajectory tracking controller for marine vehicles is presented. A small-sized unmanned ship is considered as a control object. Both speed and heading angle of a ship should be controlled for tracking control. The common point of related researches was to separate ship's speed and heading angle in control methods. In this research, a new control law from a general sliding mode theory that can be applied to MIMO (multi input multi output) system is derived and both speed and heading angle of a ship can be controlled simultaneously. The propulsion force and rudder force are also applied in modeling stage to achieve accurate simulation. Disturbance induced by wind is also tackled in the dynamics considering robustness of the proposed control scheme. In the simulation, we employed a way-point method to generate ship's trajectory and applied the proposed control scheme to ship's trajectory tracking control. Our results confirmed that the tracking error was converged to zero, thus demonstrating the effectiveness of the proposed method.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.13 no.1
• /
• pp.41-53
• /
• 1988

Line drawing images are the most proper information to represent the characteristics and shapes of digital images and used for recognition and communication. For the coding of line drawing images, common eight-direction chain code is used mostly. In the paper, the new mode selection chain code method is proposed which can compress the eight-direction chain code about twenty percents and be used for the reversible coding method of line drawing images. In this coding techniques, we set a reference mode for each quadrant around an abject pixel, and assign 3-directional code for these reference modes. Therefore a line pixel is coded with 3 bits. Also, a new corner finding method of line drawing images using this mode selection chain code is proposed in this paper.