• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.1
• /
• pp.52-58
• /
• 2014

To improve the performance of clutch actuator of clutch-by-wire system for commercial vehicles, it is necessary to understand the driving characteristics of the system. To explain and predict the effects of driving characteristics on clutch characteristics, AMESim software is used. The simulation model of clutch-by-wire system is developed in the AMESim environments under the geometrical dimensions and driving mechanisms of the clutch-by-wire system, such as the rotation speed of the DC motor, the gear ratio of the reducer, the design parameters of the release fork, the coefficient of the clutch diaphragm spring, and so on. The results show that the theoretical analysis of the clutch-by-wire system for commercial vehicles using the AMESim software find out the driving characteristics of the clutch actuator, and predict the performance characteristics of the clutch-by-wire system.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.1
• /
• pp.128-136
• /
• 2013

This study presents the development of Gateway Control Module using SAE J1939 protocol for the commercial vehicles. Presently, the load rate of CAN bus is increased by the single network composition and addition of new ECUs for development of intelligent vehicles. Because the embedded system of the integrated network control function has the errors of the CAN bus caused by the increase of ECU, it is needed for development of commercial vehicles. Also, this study presents the development of smart functions that can diagnosis CAN bus errors, fault diagnosis of ECU and basic function that arbitrates CAN bus between ECUs of commercial vehicle. GCM was designed for 4channel separation about Gateway function as solution of load rate decrease and smart functions. HILS(Hardware in the loop simulation)system that can achieve simulation about CAN Messages of all systems on vehicle was applied to evaluate performance and verification of all functions and performance. The load rate on CAN bus was decreased at using functions what was delivery, block and process of GCM. Through this, it was enabled to organize systematic architecture for gateway.

• Journal of Aerospace System Engineering
• /
• v.16 no.2
• /
• pp.25-32
• /
• 2022

A cab roof fairing is a device that reduces the drag coefficient of a commercial vehicle, by controlling the resistance of flow separation occurring in the front when the commercial vehicle travels. Commercial vehicles are designed to facilitate aerodynamic resistance that cannot be avoided from the driving direction of the vehicle, because they must structurally load containers in the rear. For this reason, it is closely related to oil costs and environmental pollutants. In this study, the 3D fairing shape was designed based on the Rankine half body theory, and the design results were verified through aerodynamic analysis.

• Tribology and Lubricants
• /
• v.29 no.5
• /
• pp.291-297
• /
• 2013

Hydraulic directional control valves actuated by solenoid are used to control emergency steering in general or hybrid electric commercial vehicles. In this study, a new lightweight hydraulic directional control valve was designed by flow and structural simulation, and was fabricated; the basic operation, pressure differentials, and inner leakage flow were evaluated experimentally. In the results, the new model showed comparable performance with an existing imported valve. New valve was 80% the weight of the existing valve and had few components. Installing this valve on a truck body is easier because of its compactness and small size.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.472-475
• /
• 2014

Abnormal cab vibrations in the Y direction in commercial vehicles during driving(70~90kph) are not common vibrations that happen to vehicles during driving and can be an obstacle to normal driving. This study conducted Operation Deflection Shape(ODS) testing to identify the causes of those abnormal cab vibrations and find solutions for them and also a sine sweep test to find resonance and frequency in the cab suspension system and set directions for improvement. The study also altered the shape of the bush inner part for changes to the rigidity features of the cab bush in the Y direction and revised the design with optimal rigidity in the Y direction, thus improving abnormal cab vibrations in the Y direction during driving.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.2
• /
• pp.86-94
• /
• 1995

For a driving vehicle, a self-excited vibration of a pair of steerable wheels about their steering axis accompanied by tramp is called shimmy. Shimmy is caused by the coupling effects of the complicated actions of wheel and tire and the tramp motion of front wheel axle. Because front axle is no longer used on passenger cars shimmy occurring is not considerable. But in commercial vehicles using front wheel axle suspension system shimmy should be considered in design process. In this paper, the model closed to a practical vehicle was developed to analyze the shimmy of a commercial vehicle, and the effects of various design parameters to shimmy were observed by dynamic simulation with multibody dynamics program, DADS. The validity of developed model and analysis results were verified by practical vehicle experiments.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.18 no.6
• /
• pp.164-175
• /
• 2019

Installation of digital tachograph, black box, and ADAS have been enforced to commercial vehicles for preventing violent driving and accidents by the Traffic Safety Act in Korea. Nevertheless, the damage caused by road hazards has increased 1.5 times in 2016 compared to 2013. So, developing new technologies that can identify road hazard using the sensors installed in commercial vehicles are conducting by the Ministry of Land, Infrastructure and Transport. As a part of the technologies, this research analyze the error range of GPS installed in commercial vehicles that vary according to the driving speed. As a result, the average error was 9.72m at the driving speed of 100km/h, and the error was 2.1 times larger than the average error of 4.69m at the driving speed of 40km/h. The event point proper integration/separation range(m) was analyzed to be 20m with a recognition rate of 90% or more at the same point regardless of driving speed. The results of this research can be used as basic data for improving the accuracy of location-based data would be collected using commercial vehicles.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.11 no.6
• /
• pp.49-59
• /
• 2012

Recently, various alternatives for safety and efficiency of commercial vehicles have been considered, and one of the new alternatives is the application of a digital tachograph. In Korea, the installation of a digital tachograph to commercial vehicles was regulated from 2011 and Korea Transportation Safety Authority developed e-TAS to analyze the monitoring data from digital tachographs installed in the order of 100 commercial vehicles. This study performs the potential impact analysis of the DTG installation, which includes a trend of dangerous driving, a trend of traffic accidents and cost-effective analysis, a trend of fuel consumption and cost-effective analysis, a cost-effective analysis of social benefits using e-TAS data. Depending on the frequency of dangerous driving, the participants are divided into three groups; high-dangerous group, average-dangerous group and low-dangerous group. The high-dangerous driving group shows lower km/liter than the low-dangerous driving group by 15% for buses and taxis and by 30% for trucks. About $CO_2$ emission, the difference becomes bigger; 25%, 25% and 42% for buses, taxis and trucks, respectively. Although this study is a short-term period analysis, the methodology will be applicable for the long-term period analysis with larger data.

• Journal of the Korean Society of Safety
• /
• v.24 no.4
• /
• pp.1-10
• /
• 2009

The characteristics of smoke emissions from diesel heavy duty vehicles which weigh over 5.5 tons was investigated by driving the vehicles with both the Lugdown 3 modes in the chassis dynamometer and tree accelerating mode under no load. The vehicles include commercial vehicles such as bus, microbus, trucks and specialized vehicles, etc. The total numbers of the vehicles tested were 200. The light extinction method was used to measure the smoke emissions from the vehicles tail pipe. The values of the smoke emissions in the tree accelerating mode showed $0{\sim}20%$ band nearly independent of both the mileage and year of production of the tested vehicles, while those in the Lugdown 3 modes showed $0{\sim}99%$ of wide band. The correlation coefficients between the values of the smoke emissions with both the Lugdown 3 modes and the free acceleration mode were 0.12, 0.08, 0.12, respectively. The inspection with Lugdown 3 modes is better one than that with tree acceleration from the point of exact inspection of the diesel vehicles' smoke emission.

• Journal of Internet Computing and Services
• /
• v.24 no.1
• /
• pp.87-97
• /
• 2023

Charger infrastructure facilities are designed and installed based on a constant power supply. Initially designed charging facilities support charging of rapidly growing electric vehicles on a limited power supply basis. In addition, current commercial vehicles can only be fully charged, and are supported by the rapid equalization charging method. However, commercial vehicles operate according to a set schedule, so flexible charging is essential. In this paper, we propose a power operation method with more than 20% efficiency improvement by using a fixed schedule-based charging scheduling and power distribution technique of a commercial bus based on the same amount of power in accordance with the rapid growth and increase of electric vehicles.