• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.5
• /
• pp.500-509
• /
• 2013

This study reports a numerical analysis of the internal flow characteristics of the integrated urea-SCR muffler system with the various geometries of the multi-perforated tube which is set up between the muffler inlet and in front of SCR catalysts. The multi-perforated tube is generally used to disperse uniformly the urea-water solution spray and to make better use of the SCR catalyst, resulting in the increased $NO_x$ reduction and decreased ammonia slip. The effects of the multi-perforated tube orifice area ratios on the velocity distributions in front of the SCR catalyst, which is ultimately quantified as the uniformity index, were investigated for the optimal muffler system design. The steady flow model was applied by using a general-purpose commercial software package. The air at the room temperature was used as a working fluid, instead of the exhaust gas and urea-water solution spray mixture. From the analysis results, it was clarified that the multi-perforated tube geometry sensitively affected to the formation of the bulk swirling motion inside the plenum chamber set in front of the SCR catalyst and to the uniformity index of the velocity distribution produced at the inlet of the catalyst.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.9
• /
• pp.733-742
• /
• 2016

In recent years, gas engines fueled with LNG or synthetic gas have been attracting considerable attention for marine use owing to their potential to facilitate better fuel economy and to reduce emissions. It has been confirmed that gas engines using the Otto cycle, which involves premixed combustion, can satisfy Tier III regulations without the EGR or SCR system. The objective of this study is to acquire simulation technologies for predicting gas engine performances in industrial fields. Using the commercial software BOOST, the simulation is conducted on a gasoline engine rather than a marine engine due to the gasoline engine's easier accessibility. This study consists of two stages. In the first stage published previously, the optimal modeling techniques for representing the behavior of the gas in the intake and exhaust systems were determined. In the current study, we formulated a method to evaluate the combustion and heat transfer processes in the cylinder and to ultimately determine the major performance parameters, given that the analytical model derived from the previous stage has been applied. Through this study, we were able to determine a combustion and heat transfer model and a valve discharge coefficient that are less reliant on empirical data: we were also able to formulate a methodology through which relevant constants are decided. We confirmed that the values of transient cylinder pressure variation, indicated mean effective pressure, and air supply can be successfully predicted using our modeling techniques.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.3
• /
• pp.235-242
• /
• 2014

To investigate pressure distributions on the shaft surface of the air bearing, the commercial CFD software was employed to study three different nozzle geometries to improve the nozzle performance: general drill-shaped, matched cube-shaped and trimmed exit nozzles. Under the influence of stagnation point, the maximum pressure was observed at the center of shaft surface for all cases. Owing to the blocking effect of a fine gap between the shaft surface and the nozzle exit, the drill-shaped nozzle has the rapid local pressure increase near the nozzle exit corner, generating the ring vortex in the radial direction within pressure ratio of 6.92, and its pressure becomes negative in a certain range of downstream. In comparison, the contoured nozzle showed a local pressure increase in the measured range of pressure ratios, but a negative pressure appeared within the pressure ratio of about 10. The trimmed nozzle was seemed to extend the high pressure zone near the stagnation point in the radial direction substantially, and no negative pressure was appeared in the whole range. Based on these observations, it is found that trimming nozzle exit becomes more effective for improving the performance than modifying the nozzle inside contour.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.3
• /
• pp.271-277
• /
• 2014

Internal structures, especially those located in the upstream of a reactor core, may have a significant influence on the core inlet flow rate distribution depending on both their shapes and the relative distance between the internal structures and the core inlet. In this study, to examine the effect of the reactor internal structure geometry treatment method on the prediction accuracy for the scale-down APR+ flow distribution, simulations with real geometry modeling were conducted using ANSYS CFX R.14, a commercial computational fluid dynamics software, and the predicted results were compared with those of the porous medium assumption. It was concluded that the core inlet flow distribution could be predicted more accurately by considering the real geometry of the internal structures located in the upstream of the core inlet. Therefore, if sufficient computational resources are available, an exact representation of these internal structures, for example, lower support structure bottom plate and ICI nozzle support plate, is needed for the accurate simulation of the reactor internal flow.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.1
• /
• pp.9-16
• /
• 2012

Recently, an optics-based concentrator for solar concentration has been a key issue in development of photovoltaic systems. In the present study, a new, simple, easily producible planar concentrator based on a light guide system is proposed. In this device, solar light is concentrated by microprism optical patterns guiding the light, mainly through total reflection and refraction. The main design variables of the concentrator are the geometric concentration ratio ($R_c$) and the ${\Theta}_1$ and ${\Theta}_2$ of the microprism pattern. Ray tracing was simulated using commercial software, SPEOS, and the optical efficiencies of the light guide solar concentrator were predicted in each case. The predicted maximum optical efficiencies are 65.60%, 54.78%, and 46.78%, respectively, for $R_c$ values of 4, 5, and 6. The variation of the optical efficiencies according to ${\Theta}_1$, ${\Theta}_2$, and the incline angle of the incident light were predicted.

• Plant Journal
• /
• v.10 no.2
• /
• pp.28-37
• /
• 2014

Recently, it is considered that environment and energy are critical issues all over the world. In power generation sector in Korea, almost power stations are constructed and operated as cogeneration plants in conformity with this trend. KDHC(Korea District Heating Corporation) goes one step further adopting renewable energy technology like heat pump using wasted heat for energy-saving and environment improvement. This study investigates the performance characteristics by the location of waste heat recovery heat pumps of 5 Gcal/h capacity in 150 MW-class Gwang-gyo cogeneration plant using commercial software 'THERMOFLEX'. Prior to analysis, the simulations are performed with actual operation data, and then the validation of simulations is verified by checking the error within 2%. After verification, the simulations are carried out with 3 locations and the effect on electrical power output and heat output is analyzed. As a result, overall efficiency of cogeneration plant is the highest in the case of heat pump located before DH(District Heating) Heater because of the largest increase of heat output despite of decrease of electrical power output.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.32 no.6
• /
• pp.349-357
• /
• 2019

Finite element method (FEM) is utilized in the development of products to realistically analyze and predict the mechanical behavior of materials in various fields. However, the approach based on the numerical analysis of glass fiber reinforced plastic (GFRP) composites, for which the fiber orientation and strain rate affect the mechanical properties, has proven to be challenging. The purpose of this study is to define and evaluate the mechanical properties of glass fiber reinforced plastic composites using the numerical analysis models of Digimat, a linear, nonlinear multi-scale modeling program for various composite materials such as polymers, rubber, metal, etc. In addition, the aim is to predict the behavior of realistic polymeric composites. In this regard, the tensile properties according to the fiber orientation and strain rate of polybutylene terephthalate (PBT) with short fiber weight fractions of 30wt% among various polymers were investigated using references. Information on the fiber orientation was calculated based on injection analysis using Moldflow software, and was utilized in the finite element model for tensile specimens via a mapping process. LS-Dyna, an explicit commercial finite element code, was used for coupled analysis using Digimat to study the tensile properties of composites according to the fiber orientation and strain rate of glass fibers. In addition, the drawbacks and advantages of LS-DYNA's various anisotropic material models were compared and evaluated for the analysis of glass fiber reinforced plastic composites.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.11 s.114
• /
• pp.1040-1049
• /
• 2006

A design method for minimizing transmission loss of a broadband right-angle transition from a coaxial cable to a microstrip line is presented. The right-angle transition has been widely used where printed circuit applications need to be fed from behind the ground plane using coaxial line. To obtain the minimized transmission loss over the whole operating frequency range of the transition, design parameters such as ground aperture and probe diameters, ground aperture offset, and stub length are optimized using a commercial electromagnetic simulation software. Results are presented for the optimum right-angle transition from an SMA connector to a microstrip line on common reinforced 0.787 mm thick PTFE substrates. Measurements of a fabricated transition show that reflection coefficient is less than -22 dB and insertion loss is less than 0.45 dB over $0.05{\sim}20GHz$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.11
• /
• pp.7990-8000
• /
• 2015

Plant factories are plant cultivation systems which produce farm products uniformly under the controlled environmental condition regardless of seasons and places. Thermal flow in the plant factory is an important parameter in cultivating plants. In this research, we study thermal flow characteristics for a hybrid plant factory with multi-layer cultivation shelves using computer simulation techniques. In order to obtain numerical solutions for thermal flow characteristics, a finite volume method was applied. We consider a low-Reynolds-number ${\kappa}-{\epsilon}$ turbulence model, incompressible viscous flows, and pressure boundary conditions for numerical simulation. Commercial software Solid Works Flow Simulation is then used to investigate characteristics of thermal flows in the plant factory applying several different inflow air velocities and arrangements of cultivation shelves. From numerical analysis results, we found that temperatures in cultivation shelves were uniformly distributed for Case 3 when the inflow air velocity was 1.6 m/s by using a blower in the plant factory. However in Case 1 lower temperature distributions were observed in test beds, TB2 and TB3, which indicated that additional temperature control efforts would be required. Average shelf temperature increased by $3^{\circ}C$ using artificial light source (DYLED47) with 50% blue and 50% red LED ratios. Korea Academia-Industrial cooperation Society.

• Proceedings of the Korean Society for Emotion and Sensibility Conference
• /
• 1999.11a
• /
• pp.401-406
• /
• 1999

생활이 풍족해질수록 사람들은 음식이나 음료를 통하여 미각을 즐기는 경향이 강해지고 있다. 미각이 발달한 사람들은 다른 감각이 발달한 사람들보다 소비 욕구가 왕성하여 상품정보에 밝은 편이고 신제품에 대한 호기심도 많아 주요고객으로 환영받을 수 있는 가능성이 매우 높다. 이러한 점을 고려할 때 미각은 소비성향의 척도가 될 수 있으며, 이것이 상품개발에 중요한 지표가 될 가능성이 있다. 그러나 맛에 민감하다거나 둔감하다고 표현되는 개인의 미각물질에 대한 감도는 개인마다 일정치 않다. 이것은 미각물질에 따라 개인의 상대적인 역치의 고조나 미각 강도의 대소가 다르거나 감도가 다른 미각물질에 대한 수용구조에 개인차가 있기 때문이다. 이처럼 개인차가 있는 미각을 표준화된 방법으로 측정하는 것은 그리 쉬운 일이 아니다. 미각강도 측정을 위한 Time-Intensity curve는 1958년 음식물의 특성에 대해 관심을 가졌던 Nielson에 의해 개발되었는데 최근에 Takagi와 Asakura가 Time-Intensity curve분석과 기록을 위해 microcomputer를 이용한 방법을 개발하였다. 그들의 방범은 Time-Intensity curve를 모니터에 보여주고 data를 floppy discs에 기록하여 software로 분석하는 것이다. 본 연구는 이것을 좀더 편리하고 단순하게 만들기 위해 감각의 강도를 전기적 저항의 interface를 통하여 computer에 입력하는 대신에 mouse를 이용하여 입력하는 방법을 개발하였다. 새로이 개발된 Time-Intensity curve를 이용하여 커피성분 중 설탕과 프림의 농도에 변화를 주어 맛의 좋고 싫음의 미각강도를 측정하는 실험을 하였다. 그 결과 상품개발의 중요한 지표가 되는 미각의 강도를 측정할 수 있었고 이것은 향후 commercial한 상품의 개발에 유용한 지표가 될 것이라고 본다.시사한다. 본 연구에서는 한국 연구 조직에서 일하는 외국인 연구자들의 동기 및 성과에 영향을 미치는 많은 요인들을 확인할 수 있었다. 상관관계, 분산분석, 회귀분석 등을 통해 활용 성과에 미치는 영향 요인들을 도출하였다. 설문 분석을 통하여 동기 및 성과 사이에는 강한 상관관계가 존재하는 것을 확인할 수 있었으며 이는 전통적인 동기 이론들과 부합한다. 대부분의 변수가 동기 및 성과에 동시에 영향을 미치는 것으로 조사되었으며 그중에서도 조직 협력 문화, 외국인 연구자의 의사소통 및 협력성, 외국인 연구자의 연구 능력 관련 변수들 및 연구 프로젝트의 기술수명주기, 외국인 연구자의 기존 기술지식의 흡수 등이 가장 중요한 변수로 나타났다. 이는 우리가 주로 중국 및 러시아 과학자들을 활용하여 상업화하는 외국인 연구인력 활용 패턴과도 일치하는 결과이다. 즉 우호적인 조직문화를 가지고 있는 연구 조직에서, 이미 과학기술 지식을 많이 가지고 있고 연구 능력도 높은 외국인 과학기술자를, 한국에서 기술이 태동 또는 성장하고 있는 연구 분야에서 활용하는 것이 가장 성과가 좋다는 사실을 확인시켜 주고 있다. 국내에서 최초로 수행된 본 연구는 외국인 연구 인력의 활용 성과가 매우 높으며, 우리의 과학기술혁신시스템을 보완하는 유효한 수단으로써 외국인 연구 인력이 중요한 대안이 될 수 있음을 발견하였다. 외국인 연구 인력을 잘 활용하기 위하여 문제점 및 개선방안을 활용 환경, 연구 인력이 중요한 대안이 될 수 있음을 발견하였다. 외국인 연구 인력을 잘 활용하기 위하여 문제점 및 개선 방안을 활용 환경, 연구 인력관리. 인력 교류사업, 외국인 과학자 지원 창구 등으로 나누어서 정리하였다. 연구시설, 주거시설 등의 하드웨어적 환경에 대한 개선도 중요하지만 연구 인력의 관리 능력 제고, 인력 교류 사업의 개선, 정보 제공 등 소프트웨어적인 활용 능력을 제고하는데 정책적인 관심을 기