• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.9 no.5
• /
• pp.49-58
• /
• 2010

The traffic signal controllers being used in the domestic currently are being manufactured based on the korean national police standard which was developed for controlling the quad-light traffic signal having the red, yellow, left-turn arrow, and green lights. But according to the national policy for the traffic operation, they have to be changed to be able to switch the tri-light signal having red, yellow and green lights. In this study, a new tri-light traffic signal controller was designed and developed by the way improving the Signal Control Unit of the existing quad-light standard traffic controller. The Load Signal Unit(LSU) was improved to output 6 signals which are the two assemblies of three signal indications having the red, yellow, and green lights. To enough traffic signals output to control each directional movements and the various transport modes which are car, bus, bike, and pedestrian etc., the connector bus system was designed to be able to accommodate maximum 96 signals outputs being constructed by 16 LSUs. Flasher device was developed to be able to support maximum 32 red signals. In the software, the communication protocol between traffic control center and the traffic signal controller was improved and new signal map code values were defined for the developed LSU controlling the quad-light traffic signal. A model of the quad-light traffic signal controller developed and was tested three operations, protocol-operation, remote-command and control-mode. The test result operated all of them successfully.

• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.332-338
• /
• 2008

This paper handles, implementation of multiple access bidirectional serial communications protocol using two common DC power lines, whict are power supply and ground, connecting multiple devices. Communication between the host and the multiple clients are performed using unique packet data with device ID unique to each devices connected on the common power lines. Host initiates data communications by transmitting command packet to the designated client with the client's ID and the client responds by transmitting response packet to the host and in this way, multiple clients and host exchange the packet through the common power lines. The normal voltage of the power communication line maintains 24V corresponding to level 1 and the host drops the voltage to 12V on sending level 0 signal, also the clients normally keeps the line voltage to 24V use pull-down circuit to drop the voltage to 12V on sending level 1 signal. Power supply originates from the host, the host senses the voltage level of the power communication lines and when the clients activates pull down circuit to send level 0 signal and the voltage drops to 12V, the hosts switches power source from 24V to 12V. Also, when clients deactivate pull down circuit to send level 1 signal, the host senses the voltage increase and switches the power source from 12V to 24V. Experimental circuit is designed with one hosts and four clients and verified the power line voltage switching operation depending on the data signal levels on the power line. The proposed research result can be applied to two wire power communications system with one host and multiple low current consumption clients.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.4
• /
• pp.396-405
• /
• 2009

This paper describes playback downlink and telecommand uplink channel design performed for a transportable small-sized KOMPSAT(Korea Multi-Purpose Satellite) ground station. As a result of downlink channel design, required receiving performance was calculated from the threshold signal-to-noise ratio of playback signal and it was revealed that this performance can be guaranteed in 1.5 m ground station with 6.5 dB/K of G/T. For the uplink channel design, 40 dBW of EIRP was derived from the threshold signal-to-noise ratio of telecommand signal received at on-board receiver. The implemented small-sized ground station based on design was evaluated to be fully acceptable for KOMPSAT TT&C(Telemetry, Tracking and Command) system and playback downlink design without taking account of additional 3 dB system link margin was shown to be effective because it had provided constantly initial channel performance without any remarkable degradation over several years of tests with KOMPSAT and KOMPSAT-2, for both uplink and playback downlink in the elevation angle above $10^{\circ}$.

• Journal of the Institute of Convergence Signal Processing
• /
• v.10 no.4
• /
• pp.280-288
• /
• 2009

In this paper, we developed new time information recording module of VSI (VLBI Standard Interface) format by analyzing the Mark5B recorder control and operation software with 1Gbps speed, which is able to record the weak signal of space radio source, through the Korean VLBI Network (KVN). The control and operation software of high-speed recorder consists of 2 kinds of software, which is that it can operate RAID control board by controlling large capacity HDD drive and the network control and operation. Especially, core software in high-speed recorder is able to output the results after performing and analyzing the input command. Through the analysis of control and operation software, new time information recording module, which is needed to process the observed data for correlation, is developed. New developed time information recording module can record the time information together after checking the interrupt of 1PPS(Pulse Per Second) input signal when the observed data will be recorded. To verify the normal operation of the developed time information recording module, we performed the real observation test and confirmed the effectiveness of developed software through analyzing the recorded observation data.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.2274-2277
• /
• 2003

A cylindrical permanent magnet inside the four-phase permanent magnet (PM) stepping motor is employed as the rotor. The stator has four teeth around, which its coils are wound. The mode of excitation can be classified into 3 modes: single-phase excitation, two-phase excitation and ministep excitation. The ministep drive is a method to subdivide one step into several small steps by means of electronics. The paper presents the programmable ministep technique drive. This technique decodes the results obtained from the counter to locate the data in Read Only Memory (ROM). The Sinusoidal Pulse Width Modulation (SPWM) is transformed to binary file and saved to the ROM. The experiment is performed with the four-phase PM stepping motor and drives from a two-phase programmable sinusoidal ministep signal, instead of square wave. The results show that the performances of the proposed programmable ministep technique drive have high efficiency, smooth step motion, and high speed response. Moreover, the resolution of sinusoidal ministep signal can be controlled by the input frequency (f command).

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.171-174
• /
• 2005

The circuit simulation analysis and diagnosis methods are used to instruments in detail when they give apparently abnormal readings. In this paper, a new simulator through an analysis of the important circuits modeling under severe accident conditions has been designed, the realization for a body work instead of the two sorts of the Labview & Pspice as an one order command in the Labview program. The program can be shown the output graph form the circuit modeling as an order commend. The procedure for the simulator design was divided into two design steps, of which the first step was the diagnosis methods, the second step was the circuit simulator for the signal processing tool. It has three main functions which are a signal processing tool, an accident management tool, and an additional guide from the initial screen.

• Journal of Power Electronics
• /
• v.10 no.3
• /
• pp.285-292
• /
• 2010

This paper presents a current mode integrated control technique (CM-ICT) using a modified voltage space vector modulation (MSVM) for Z-source inverter (ZSI) fed induction motor drives. MSVM provides a better DC voltage boost in the dc-link, a wide range of AC output voltage controllability and a better line harmonic profile. In a voltage mode ICT (VM-ICT), the outer voltage feedback loop alone is designed and it enforces the desired line voltage to the motor drive. An integrated control technique (ICT), with an inner current feedback loop is proposed in this paper for the purpose of line current limiting and soft operation of the drive. The current command generated by the PI controller and limiter in the outer voltage feedback loop, is compared with the actual line current, and the error is processed through the PI controller and a limiter. This limiter ensures that, the voltage control signal to the Z-source inverter is constrained to a safe level. The rise and fall of the control signal voltage are made to be gradual, so as to protect the induction motor drive and the Z-source inverter from transients. The single stage controller arrangement of the proposed CM-ICT offers easier compensation. Analysis, Matlab/Simulink simulations, and experimental results have been presented to validate the proposed technique.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.10
• /
• pp.927-932
• /
• 2010

Estimation methods of motion intention from bio-signal present challenges in man machine interaction(MMI) to offer user's command to machine without control of any devices. Measurements of meaningful bio-signals that contain the motion intention and motion estimation methods from bio-signal are important issues for accurate and safe interaction. This paper proposes a novel motion estimation sensor based on a geometrical muscle changes, and a motion estimation method using the sensor. For estimation of the motion, we measure the circumference change of the muscle which is proportional to muscle activation level using a flexible piezoelectric cable (pMAS, piezo muscle activation sensor), designed in band type. The pMAS measures variations of the cable band that originate from circumference changes of muscle bundles. Moreover, we estimate the elbow motion by applying the sensor to upper limb with least square method. The proposed sensor and prediction method are simple to use so that they can be used to motion prediction device and methods in rehabilitation and sports fields.

• Proceedings of the IEEK Conference
• /
• 2002.06e
• /
• pp.95-98
• /
• 2002

This paper presents a study on DSP(TMS320F240) controller design for multi-axes transportation system using BLDC servo motor. This BLDC servo motor controller was realized with DSP(Digital Signal Processor) and IPM (Intelligent Power Module). The multi-axes transportation system needs torque, speed, position control of servo motor for variable action. This paper implements those servo control with vector control and space vector modulation technique. As CPU of controller DSP(TMS320F240) is adopted because, it has PWM(Pulse Width Modulation) waveform generator, A/D(Analog to Digital) converter, SPI(Serial Peripheral Interface) port and input/output port etc. The controller of multi-axes transportation system consists of 3-level hierarchy structure that main host PC manages three sub DSP system which transfer downword command and are monitoring the states of end servo controllers. Each sub DSP system operates eight BLDC servo controllers which control BLDC servo motor using DSP and IPM Between host system and middle digital signal processor communicate with RS-422, between main processor and controller communicate with SPI port.

• Journal of the Institute of Convergence Signal Processing
• /
• v.9 no.3
• /
• pp.230-237
• /
• 2008

Recently, lots of interest and competition in developments related to the autonomous-vehicle robot are being further increased. However, the absence of the standard architectures for effectively controlling the autonomous-vehicle robot led to many difficulties such as the long duration of development and the uncompatibility with other autonomous-vehicle robots. Accordingly, we implemented a mobile autonomous-vehicle robot system based on JAUS standard architecture. The mobile robot communicates with the remote-control system by using wireless LAN UDP/IP JAUS command massages. Its effectiveness is showed through the experimental results related to the navigation of implemented robot.