• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.05a
• /
• pp.59-63
• /
• 2003

This paper describes the conceptual design method of subscale direct-connect test facility for liquid fuel ramjet combustion study and preliminary analysis of test results. The measured pressure signal represents the successful operation of the test facility. The pressure oscillation in combustion chamber shows the dominant frequency of 190Hz, relatively very low frequency to 1L acoustic mode (1200Hz) based on the length of combustor. It is suspected that there were several driving sources, which are vortex street at backward step of combustor, inlet resonance induced by the long length of unchecked inlet, and/or combustor configuration with optical window.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.1
• /
• pp.83-89
• /
• 2011

A design plan was proposed for determining combustor configuration of regenerative- cooled liquid rocket engine in the process of preliminary design. Rocket performance and regenerative cooling results were calculated using the properties of combustion gas estimated in CEA. For required thrust, chamber pressure, atmosphere pressure and propellant mixture ratio the mass flow rate of propellants and combustor performance were predicted by one-dimensional and experimental correlations. Finally, determinable plan for the contour of combustor were presented through Rao nozzle design method.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.37-42
• /
• 2010

A design plan was proposed for determining combustor configuration of regenerative- cooled liquid rocket engine in the process of preliminary design. Rocket performance and regenerative cooling results were calculated using the properties of combustion gas estimated in CEA. For required thrust, chamber pressure, atmosphere pressure and propellant mixture ratio the mass flow rate of propellants and combustor performance were predicted using one-dimensional and experimental equations. Finally, determinable plan for contour of combustor were presented through Rao nozzle design method.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.406-407
• /
• 2009

The thermal protection techniques for ramjet combustor are key technology, which block the heat from hot combustion gas, and maintain the structure temperature safely. Film cooling method is one of them. This research proposes the optimal thermal design method through performing the study of thermal protection design for ramjet combustor.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.3
• /
• pp.237-242
• /
• 2009

MEMS catalytic combustors were fabricated to use in micro-power sources as a heat source. The combustor was fabricated by photolithography and anisotropic wet etching of photosensitive glass wafers. Two different catalyst loading methods were used to complete the fabrication of the combustors. For thin film type, the $Al_2O_3$ was washcoated on the surface of the combustion chamber as a catalyst support, and for packed-bed type, ceramic foam was inserted after Pt was coated. The volume of the combustors was 1.8 $cm^3$ and 16W of heat was generated using the fabricated combustors with hydrogen. The energy density of combustor was about 8.9 W/$cm^3$.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.8
• /
• pp.2681-2692
• /
• 1996

The finite-volume method for radiation in a three-dimensional non-orthogonal gas turbine combustion chamber with absorbing, emitting and anisotropically scattering medium is presented. The governing radiative transfer equation and its discretization equation using the step scheme are examined, while geometric relations which transform the Cartesian coordinate to a general body-fitted coordinate are provided to close the finite-volume formulation. The scattering phase function is modeled by a Legendre polynomial series. After a benchmark solution for three-dimensional rectangular combustor is obtained to validate the present formulation, a problem in three-dimensional non-orthogonal gas turbine combustor is investigated by changing such parameters as scattering albedo, scattering phase function and optical thickness. Heat flux in case of isotropic scattering is the same as that of non-scattering with specified heat generation in the medium. Forward scattering is found to produce higher radiative heat flux at hot and cold wall than backward scattering and optical thickness is also shown to play an important role in the problem. Results show that finite-volume method for radiation works well in orthogonal and non-orthogonal systems.

• Transactions of the Korean hydrogen and new energy society
• /
• v.18 no.4
• /
• pp.406-412
• /
• 2007

An experimental study on the design of a catalytic combustor for 1.6 kW MCFC system has been performed. The roles of the catalytic combustor are to completely burn anode off-gas and to supply sufficient $CO_2$ to cathode channels. In order to avoid hot spot or fuel slippage, flow uniformity at the catalyst inlet was achieved by installing two crossing perforated plates between the catalyst and the mixing chamber with minimal pressure drop. A Pd/Ce/Ni-$Al_2O_3$ catalyst was used for complete combustion of the off-gas at GHSV=36,000.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.2
• /
• pp.271-278
• /
• 1987

The experimental study was carried out to investigate the pressure fluctuation, operating frequency, noise emission and combustion characteristics in an aero-valved pulsating combustor. Measurements of the pressure fluctuation, mean temperature and ion current inside the combustion chamber indicate that combustion phenomena are characteristically similar to those in the diffusion flame. The measured frequency schedue indicates that the acoustic theory of the quarter wave tube can be approximated to give the operating frequency, but correction factor must be involved to estimate the correct operating frequency. The spectral behavior of the noise emission exhibits that frequency bands with high noise intensity are narrowly restricted to the neighborhood of the operating frequency signalling the low-frequency combustion characteristics of the pulsating combustor. Measurements of the operating characteristics as variation of the fuel nozzle diameter and injection angle with 4 fuel nozzles have been made, and it was found that the system produced the stable operating conditions up to the turn down ratio of 3 when the fuel nozzle diameter is 1.2mm, and the optimum fuel injection angle is thought to be in the neighborhood of 30.deg. radially.

• Journal of the Korean Society of Combustion
• /
• v.10 no.1
• /
• pp.27-36
• /
• 2005

In this study, we investigated characteristics of a gas flow and a combustion property during the combustion of a RDF in a pyrolysis melting incinerator with disposal rate of 30 kg/hr. The RDF was pyrolyzed through the pyrolysis chamber at $600^{\circ}C$ of the chamber surface without oxygen condition. The pyrolysis gas was injected in the combustion chamber. It was burned by means of the staged combustion that was injecting secondary and tertiary air in the combustor. We measured the temperatures and the gas components in the combustion chamber while maintaining the air-fuel ratio of 1.3. Finally, we confirm that additional air injection, secondary and tertiary air ratio, was the most important factor to reduce NOx.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.15 no.4
• /
• pp.17-23
• /
• 2007

This paper describes the flow and performance characteristics inside the post-chamber of the multi-port hybrid rocket motor. Using the computational fluid dynamics (CFD) technique, the non reactive compressible flow fields in the downstream of the fuel grain was numerically calculated. The motor performance obtained from computational results were in agreement with that conducted by the ground motor firing test. Besides, the flow field characteristics inside the post-chamber were discussed under different port numbers (1 port and 3 ports) of the fuel grain. The flow pattern showed that the performance of multi-port hybrid rocket motor having three grain ports is higher than that of the single-port one due mainly to the difference of incoming mass flow rate irrespective to the pressure field.