• Journal of the Korean Society of Combustion
• /
• v.4 no.2
• /
• pp.11-22
• /
• 1999

Combustion characteristics of the wood chips(balsa chips) were experimentally investigated with respect to the thermal recycle system of the urban waste. The urban waste contains plastics, vegetable and wood materials. Wood was chosen as an example of the one of the component of urban dust. A small wood chip was burned in a electric furnace by the micro-electric balance. The mass reduction rate was normalized by the initial mass of test piece and the time of volatile combustion end. When the mass of the wood chips(balsa chips) was larger than 0.5g, the combustion similarity was found on the normalized mass reduction rate.

• 한국연소학회:학술대회논문집
• /
• 2012.11a
• /
• pp.339-340
• /
• 2012

The purpose of this study is to analyse, the basic parameters through experimentally and with CFD modelling, internal recirculation of the flameless combustion of natural gas. The test rig is made up of a vertical combustion chamber of circle cross section. The inner dimensions of the chamber are $0.2m{\times}1m$ (diameter x height). And CFD simulations of the combustion chamber have been performed using FLUENT 14.0. Some results of this study present the basic parameters and data of flameless combustion.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.368-372
• /
• 2003

There arc two methods to evaluate the combustion product, that is analysis method and measurement method. Properties of the combustion products, constituents, and quanties, can be used to calculate boiler efficiency and beat losses. Using combustion evaluation methods combustion calculation were performed at certain condition and analyze the results. In this paper by comparing the results between two methods, deviation, correction and possibility of site application were confirmed

• 한국연소학회:학술대회논문집
• /
• 2003.12a
• /
• pp.145-152
• /
• 2003

The objective of the present study is to develop methodology for the assesment of combustion stability of liquid rocket injectors. To simulate actual combustion occurring inside of a thrust chamber, a full-scale injector has been employed in the study, which burns gaseous oxygen and mixture of methane and propane. The main idea of the experiment is that the mixing mechanism is considered as a dominant factor significantly affecting combustion instability in a full-scale thrust chamber. Single & multi split triplet injectors have been used with an open-end cylindrical combustion chamber. The characteristics revealed by excited dynamic pressures in gaseous combustion show degrees of relative acoustic damping depending on operating conditions. Upon test results, the direct comparison between various types of injectors can be realized for the selection of the best design among prospective injectors.

• 한국연소학회:학술대회논문집
• /
• 2003.12a
• /
• pp.131-136
• /
• 2003

Experimental study on combustion characteristics of double swirl coaxial injectors has been conducted for the assessment of critical design parameters of injectors. A subscale thrust chamber has been fabricated with a water-cooled copper nozzle, which allows a chamber to be reused without replacing parts. Two different designs of injectors have been tested for the understanding of the effects of recess length on combustion. Clearly, the recess length drastically affects the combustion efficiency and hydraulic characteristics of the injector. Internal mixing of propellants in the injector with the recess number of two increases a combustion efficiency and reveals sound combustion although a pressure drop required for the similar amount of mass flow rates increases compared with the injector of the recess number of one.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.4
• /
• pp.31-35
• /
• 2004

A new combustion strategy called LIFC(Late Injection ＆ Fast Combustion) was developed for simultaneous reduction of particulate matter(PM) and nitrogen oxides(NOx) in exhaust emission of diesel engines, In this study, effects of injection timing and injection pressure under relatively high EGR rate were investigated. The experiments were conducted in a conventional engine over a range of commercial engine speed. The test engine could be operated in LIFC up to 2000rpm / bmep 5 bar condition with significant reduction of NOx and PM. The experimental results showed potential for the mechanism of the simultaneous reduction of NOx and PM from HSDI diesel engines.

• Fire Science and Engineering
• /
• v.28 no.2
• /
• pp.48-53
• /
• 2014

In this study, we would evaluate fire risk by domestic standard for artificial turf installed on field and roofs. Today domestic regulation for artificial turf only applies to outdoor uses and especially KS M 3888-1 has compulsion but limited to school athletic facilities. Indoor regulation complying with National Emergency Management Agency (No. 2012-35) was enacted as recommendations. Thus this study did combustion test of artificial turf installed on field. Analyzed result by 45 degree flammability test, standard was inadequate to judge the fire risk so we compared and analysed its characteristic through combustion test of flame retardant finishing carpet used as flooring. Test and assessment result of its ignitionability by 45 degree flammability test showed that carpet was satisfied with flame retardant finishing performance standard contrary to artificial turf. For this reason, by conducting cone calorimeter test, the combustion property after ignition would be analyzed and evaluated and then this study will suggest a countermeasure for strengthening standard.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.5
• /
• pp.19-26
• /
• 2011

In order to investigate the effect of fuel injection hole configuration within the scramjet combustor, experiment and quasi-one-dimensional analysis was performed. And the results were compared with experiment and analysis result which were performed in 2008 with same facility and test condition. Fuel injection hole size was decreased and quantity was increased. However the depth of fuel penetration and flow quantity of fuel were maintained. As a test result, combustion performance was increased significantly with no-cavity injector and slightly with plain-cavity. However, combustion performance with zigzag-cavity was decreased.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.11
• /
• pp.1587-1594
• /
• 2003

Increased energy costs have placed demands for improved combustion efficiency, high equipment availability, low maintenance and safe operation. Furthermore low NO$_x\$ modification, installed due to strict environmental legislation, requires very careful combustion management. The flame monitoring system has been developed specially to satisfy these requirements. We aimed at gaining the relationship between the burner flame image and emissions such as NO$_x$ and unburned carbon in furnace by utilizing the image processing method. For the first step of development, its possibility test was undertaken with bench furnace. The test proceeded to the second step with pilot furnace and the system was observed to be effective for evaluating the combustion conditions. By using this technology, it is possible to perform continuous monitoring of the combustion conditions and instant detection of individual changes for each burner to prevent future loss of ignition. This may contribute to the saving of burner adjusting times for the changes of loads and fuels and to the reduction of the slagging as well.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.7 no.4
• /
• pp.63-72
• /
• 2003

The combustion characteristics of the KSR-III engine were investigated numerically from the viewpoint of performance and combustion field. For numerical analysis of KSR-III engine with hub-and-spoke baffle, 3-D calculation was performed about $30^{\cire}$ section and the prediction of performance was in a good agreement with hot-firing test result. As a result of baffle installed, the performance of KSR-III engine was reduced in comparison with no baffle case and local high temperature region appeared on injector plate, combustion wall and baffle wall, This calculation was used practically as basic data for designing injector plate with film cooling holes and predicting the performance of KSR-III final flight test.