• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.8
• /
• pp.2030-2038
• /
• 1995

In this study, three turbulent flame propagation models are compared using experimentally measured data of a 4 valves/cylinder spark-ignition engine. First two conventional models are B.K model and GESIM combustion model. The burning rates calculated from the two models are compared with the burning rates calculated from measured pressure data using the one-zone heat release analysis. GESIM combustion model predicts burning rates closer to the data acquired from the experiment in wide operating ranges than B-K model does. The third model is refined based on GESIM combustion model by including the effect of flame stretch, turbulent length scale band pass filter and a variable that considers flame size and the area of flame contacting the cylinder wall surface. The refined combustion model predicts burning rates closer to experimental results than GESIM combustion model does. Also, the refined combustion model predicts flame radius close to the experimental result measured by using optical fiber technique.

• Journal of Korean Society for Atmospheric Environment
• /
• v.19 no.4
• /
• pp.427-436
• /
• 2003

This study is to establish a waste bed combustion model that can be available to assist the design of incinerators for efficient operation control of municipal waste incinerators. An unsteady one -dimensional bed combustion modeling was developed which incorporates the various sub-process models and solves the governing equations for both gases and solids in the waste bed combustion phenomena. The combustion characteristics and the properties of the combustion gas released from the bed were investigated by using a developed model. Besides, a sub-model which predicts the formation and destruction of nitrogen oxides in the waste bed was also developed as a post-processor for the waste combustion model. It is found that the reduction rate of nitrogen oxides is enhanced in the char layer.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.3
• /
• pp.300-310
• /
• 1999

A constant-volume combustion chamber is developed to measure the burnt gas temperature over the wide ranges of equivalence ratio from 1.5 to 2.7 and pressure from 0.1 to 2.7 and pressure from 0.1 to 6 MPa by two-color method. The combustion temperature is also calculated by the conventional two-region model. The premixed fuel rich propane-oxygen-inert gas mixtures under high pressures are simultaneously ignited by eight spark plugs located on the circumference of combustion chamber with 45 degree intervals. The eight converging flames compress the end gases to high pressures. The transmissiv-ity in the chamber center during the final stage of combustion at the highest pressure is measured by in situ laser extinction method. Comparisons are made with the combustion temperatures between two-color method and two-region model. It is found that the burnt gas temperature mea-sured by two-color method is higher than that calculated by two-region model because of being the negative temperature gradient on the calculation and the temperature distribution of light path-length on the measurement and the burnt gas temperature for the turbulent combustion is higher than that of the laminar combustion under the same conditions because the heat loss for turbulent combustion is lower due to the shorter combustion period.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.8
• /
• pp.2201-2209
• /
• 1994

Macroscopic combustion models used in gun interior ballistic codes are discussed and experimental methods to measure propellant burning rate are reviewed. Comparing with gun firing results, the limit of combustion model is shown and modified combustion model is proposed. But combustion model should be selected with respect to total gun system including propellants.

• 한국연소학회:학술대회논문집
• /
• 2015.12a
• /
• pp.301-304
• /
• 2015

With the experiment observation of single particle combustion, this model is built for the numerical analysis of the process. It's about the single coal particle combustion process under different conditions with reasonable assumptions. The model can express the mass, radius, density, temperature changing with different particle sizes, oxygen concentration and gas temperature. It also includes the flame sizes change in different condition and the diffusion of each species. The result shows the characters of the combustion.

• Journal of Mechanical Science and Technology
• /
• v.18 no.6
• /
• pp.1010-1018
• /
• 2004

This study presents the methodological aspects of combustion instability modeling and provides the numerical results of the model (sub-scale) combustion chamber, regarding geometrical dimensions and operating conditions, which are for determining the combustion stability boundaries using the model chamber. An approach to determine the stability limits and acoustic characteristics of injectors is described intensively. Procedures for extrapolation of the model operating parameters to the actual conditions are presented, which allow the hot-fire test data to be presented by parameters of the combustion chamber pressure and mixture (oxidizer/fuel) ratio, which are customary for designers. Tests with the model chamber, based on the suggested scaling method, are far more cost-effective than with the actual (full-scale) chamber and useful for injector screening at the initial stage of the combustor development in a viewpoint of combustion instabilities.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.3
• /
• pp.26-36
• /
• 2010

This paper provides a description of the combustion model to obtain an accurate dynamic engine phenomena that satisfies real-time simulation for model-based engine control. The combustion chamber is modeled as a storage device for mass and energy. The combustion process is modeled in terms of a two-zone model for the burned and unburned gas fractions. The mass fraction burnt is modeled in terms of a Wiebe function. The instantaneous net engine torque is calculated from the engine speed and the instantaneous piston work. The modeling accuracy has been tested with a cylinder pressure data on a test bench and also the ability of real-time simulation has been checked. The results show that combustion model yields sufficiently good performance for the model-based control logic design. However the influence factors effected on model accuracy are some room for improvement.

• Journal of ILASS-Korea
• /
• v.22 no.1
• /
• pp.29-35
• /
• 2017

This paper describes the effects of spray breakup model constants on spray and combustion characteristics in single cylinder compression engine. KIVA-3V code coupled with a CHEMKIN chemistry solver was used for numerical analysis. In this study, spray simulations and combustion simulations are studied simultaneously. Spray simulation was conducted in constant volume to reduce the effects of air-flow as swirl or tumble. The model validation was conducted and there are little difference between experiments and simulation, this differences were reasonable. In spray simulation, the effects of model constants on spray tip penetration, spray patter and SMD were studied. Furthermore, the analysis of effects of breakup variables on combustion and emissions characteristics was conducted. The results show the KH-RT breakup model constants affects spray and combustion characteristics strongly. Increasing KH model variable (B1) and RT model constants ($C_{\tau}$, $C_{RT}$) induced slower breakup time.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2862-2867
• /
• 2008

High-temperature components of gas turbine operated for certain period of time can be reused by being repaired or rejuvenated. In case of the gas turbine combustion liners, the biggest and the most important one in the high-temperature components, come in a repair shop after operated for 8,000 or 12,000 hours according to the model and go through the repair and rejuvenation in order to be reused. A stated combustion liner is the first channel which has the combustion gas reached a nozzle from a fuel nozzle. Materials and coating properties of old and new model combustion liners were investigated. To repair these components after the visual inspection, the coatings of combustion liners were removed and then FPI(Fluorescent Penetrant Inspection), a kind of the NDI(Non-Destructive Inspection), was conducted. Damage patterns and the number of the damaged components were classified and analyzed based on data provided from the visual inspection over a long period of time. Focusing on the difference between old model and new model combustion liners, we analyzed the damage distribution and changes and consequently concluded that new model combustion liner would increase repair rate.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.9
• /
• pp.659-668
• /
• 2008

Combustion instability has been considered as very important issue for developing gas turbine and rocket engine. There is a need for fundamental understanding of combustion instability. In this study, combustion instability was numerically and experimentally investigated in a dump combustor with bluff body. The fuel and air mixture had overall equivalence ratio of 0.9 and was injected toward dump combustor. The pressure oscillation with approximately 256Hz was experimentally obtained. For numerical simulation, the standard k-$\varepsilon$ model was used for turbulence and the hybrid combustion model (eddy dissipation model and kinetically controlled model) was applied. After calculating steady solution, unsteady calculation was performed with forcing small perturbation on initial that solution. Pressure amplitude and frequency measured by pressure sensor is nearly the same as those predicted by numerical simulation. Furthermore, it is clear that a combustion instability involving vortex shedding is affected by acoustic-vortex-combustion interaction. The phase difference between the pressure and velocity is $\pi$/2, and that between the pressure and heat release rate is in excitation range described by Rayleigh, which is obvious that combustion instability for the bluff body combustor meets thermoacoustic instability criterion.