• 한국연소학회지
• /
• 제20권1호
• /
• pp.15-23
• /
• 2015

This paper presents the results of field demonstration for fuel switching to bio-fuel oil in 4 commercial heavy oil fired power plants. The 100% fuel switching field demonstration was successfully carried out in two tangential-firing boilers at a capacity of 75 and 100 MWe respectively without major equipment retrofit, and also 25% bio-fuel oil blending for two opposite firing boilers at a capacity of 350 and 400 MWe respectively. Despite the low density and heating value, the bio fuel was successfully replaced heavy fuel oil at the full load by only adjusting operational parameters. Incase of bio fuel oil combustion, heat absorption of radiative heat transfer section was reduced while convection section has opposite trend. In pollutants emission, a major reductionin SOx as well as 10-20% reduction in NOx were achieved by the fuels witching. On the other hand, boiler efficiency was slightly underestimated.

• 한국자동차공학회논문집
• /
• 제22권2호
• /
• pp.83-90
• /
• 2014

The main purpose of the study is to investigate the ideal manner and ratio to inject gasoline and DME simultaneously into intake port, and moreover to confirm the characteristics of combustion and emission of engine. Experimental conditions are 1200 rpm, compression ratio 8.5, intake air temperature (383 K). Internal cylinder pressure was collected to confirm the characteristics of combustion in order to calculate the heat release rate in the cylinder. In addition, HORIBA (MEXA 7100) which was possible analyzing emissions (NOx, CO, HC) was used. Vanguard gasoline engine (23HP386447) was used in this experiment. The result show that fuel design (DME-Gasoline) leads to the decrease of low temperature heat release, which is a benefit for higher-load on the HCCI engine. Also, IMEP and the indicated thermal efficiency increase with combustion-phasing retard, and these observations can be explained by considering the control of low temperature oxidation of DME.

• 전기학회논문지
• /
• 제58권2호
• /
• pp.327-331
• /
• 2009

Nano-porous $TiO_2$ powder was fabricated using Acetylene black, applied photo voltaic device based on the Dye-sensitized Solar Cells (DSCs) was investigated experimentally. $TiO_2$-powder was fabricated using Ti-isopropoxide and 2-propanol by sol-gel combustion method. For cases of variable Acetylene black, characteristic of porosity, size of particle and crystallite of obtained $TiO_2$ nano-powder was investigated. The photovoltaic efficiency of the prepared DSCs was measured using $TiO_2$ film which prepared on each different heat treatment temperature($400^{\circ}C{\sim}700^{\circ}C$) with paste of $TiO_2$ powder. The porosity and size of particle of $TiO_2$ powder made with Acetylene black 0.4g was influenced significantly effect to DSCs characteristic. Heat treatment at $500^{\circ}C$ makes the better photovoltaic efficiency which 5.02%($J_{sc}=11.79mA/cm^2$, $V_{oc}=0.73V$, ff=0.58). The sol-gel combustion method was useful to DSCs fabrication.

• 전기학회논문지
• /
• 제58권2호
• /
• pp.322-326
• /
• 2009

In this work, nanoporous $TiO_2$ powder was fabricated using Ketjen black, and applied in photovoltaic device based on the Dye-sensitized Solar Cells (DSCs). $TiO_2$ powder was fabricated using Ti-isopropoxide and 2-propanol by sol-gel combustion method. For added $0{\sim}2g$ variable of Ketjen black, characteristic of porosity, size of particle and crystallite of obtained $TiO_2$ nano powder was investigated. The photovoltaic efficiency of the prepared DSCs was measured using $TiO_2$ film which prepared on each different heat treatment temperature($100^{\circ}C{\sim}600^{\circ}C$) with paste of $TiO_2$ powder. The porosity and size in particle of $TiO_2$ powder made with Ketjen black Ig was influenced significantly effect to DSCs characteristic. Heat treatment at $500^{\circ}C$ makes the better photovoltaic efficiency which around 6.11%($J_{sc}=13.35mA/cm^2$, $V_{oc}=0.73V$, ff=0.63). The sol-gel combustion method was useful to DSCs fabrication.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권4호
• /
• pp.446-453
• /
• 2000

The closed cycle diesel system is operated in closed circuit system where there is non air breathing with working fluid consisted of the combination of oxygen, argon and recycled exhaust gas for obtaining underwater or underground power sources. this study has been carried out to analysis the performance of closed cycle system by means of investigation on the combustion characteristics of diesel engine MTU8V183TE52 operating in open, semi-closed, and closed cycle modes. The combustion in closed mode starts a little bit earlier than in open cycle mode. The oxygen concentration and fuel consumption at 240kW closed cycle running are 21∼24% by volume and 77∼79kg/h, respectively. The maximum cylinder pressure and ignition delay time are investigated 110bar and 8.9degree. Also, The combustion simulation program has been studied to predict whether or not combustion. The results from numerical prediction for the basic, cylinder averaged quantities such as the cylinder pressure and the heat release showed excellent with the experimental data.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.1122-1126
• /
• 2017

KSLV-II 가속모터는 한국형발사체에 사용하는 단분리모터의 한 종류이며 역추진모터와 동시에 작동하여 단분리를 수행한다. 가속모터의 목표 성능에 맞는 내탄도 설계, 추진제 조성 적용, 연소관 및 경사형 노즐 설계를 수행하였다. 연소관 및 노즐의 소재로 티타늄 합금을 적용하였으며 알루미늄이 다량 함유된 추진제에 대한 내열 성능 확보를 위한 노즐 내열재 소재를 선정하였다. 지상연소시험을 수행하여 KSLV-II 요구조건에 맞는 가속모터의 연소 성능을 확보하였다.

• 생물환경조절학회지
• /
• 제9권4호
• /
• pp.212-222
• /
• 2000

본 연구는 온실 난방시스템의 연소 체임버에 부착된 연소가스 배출연통에 열회수기를 장착하여 배출가스로부터 열을 회수하는 열회수장치의 성능에 대해 실험·분석하였다. 열회수시스템은 LPG 연소 체임버와 두 개의 열회수기로 구성되어있다. 열회수기-A는 배기가스 연통에 직접 연결되어 있으며 열회수기-B는 열회수기-A에 직렬로 연결되어 있다. 회수되는 열량은 가스의 질량흐름율과 두 측점간의 엔탈피 차이로서 산정하였으며 5가지의 송풍전압별로 각 열회수기의 성능을 검토하였다. 각 열회수기의 공기튜브 다발에 공급된 공기와 튜브 다발에 가로질로 통과하는 연소가스간의 열교환, 열회수기 유·출입부간의 압력감소, 열회수기의 총열회수성능 등으로 온실의 연통을 통해 낭비되는 열을 회수하여 연료 절감 효과를 얻을 수 있는 최적의 열회수장치 설계용 기초자료 확보에 본 연구의 목적이 있다.

• 한국연소학회지
• /
• 제17권1호
• /
• pp.48-57
• /
• 2012

Laminar lifted propane coflow-jet flames diluted with nitrogen were experimentally investigated to determine heat-loss-related self-excitation regimes in the flame stability map and elucidate the individual flame characteristics. There exists a critical lift-off height over which flame-stabilizing effect becomes minor, thereby causing a normal heat-loss-induced self-excitation with O(0.01 Hz). Air-coflowing can suppress the normal heat-loss-induced self-excitation through increase of a Peclet number; meanwhile it can enhance the normal heat-lossinduced self-excitation through reducing fuel concentration gradient and thereby decreasing the reaction rate of trailing diffusion flame. Below the critical lift-off height. the effect of flame stabilization is superior, leading to a coflow-modulated heat-loss-induced self-excitation with O(0.001 Hz). Over the critical lift-off height, the effect of reducing fuel concentration gradient is pronounced, so that the normal heat-loss-induced self-excitation is restored. A newly found prompt self-excitation, observed prior to a heat-loss-induced flame blowout, is discussed. Heat-loss-related self-excitations, obtained laminar lifted propane coflow-jet flames diluted with nitrogen, were characterized by the functional dependency of Strouhal number on related parameters. The critical lift-off height was also reasonably characterized by Peclet number and fuel mole fraction.

• 한국연소학회지
• /
• 제21권4호
• /
• pp.39-47
• /
• 2016

The aims of this research were to investigate combustion characteristics of lab-scale pressurized oxy-fuel combustion(POFC) system. In this study, the reactor, 800 mm long, was equipped with co-axial burner. Low calorific value syngas that is composed of mainly CO and $H_2$ was used as fuel whereas pure oxygen was used as an oxidant. Thermal heat input to the reactor varied from 2.6 kW to 6.1 kW. The reactor pressure also increases from atmospheric up to 15 bar. The results show that as the pressure increase, the temperature of reactor decreases on the whole in all cases. A significant temperature drop was observed especially at the bottom section of the reactor that exist flame. In addition, the flame instability increases as the pressure increases. Furthermore $NO_x$ emissions increases from atmospheric up to 2 bar. However beyond 2 bar, $NO_x$ emission reduces as pressure increases. Lastly $NO_2$ ratio in $NO_x$ also increases as pressure increases.

• 한국자동차공학회논문집
• /
• 제20권3호
• /
• pp.141-147
• /
• 2012

A direct injection diesel engine with large amount of exhaust gas recirculation was used to investigate low temperature diesel combustion. Pilot injection strategy was adopted in low temperature diesel combustion to reduce high carbon monoxide and hydrocarbon emissions. Combustion characteristics and exhaust emissions of low temperature diesel combustion under different pilot injection timings, pilot injection quantities and injection pressures were analyzed. Retarding pilot injection timing, increasing pilot injection quantity and higher injection pressure advanced main combustion timing and increased peak heat release rate of main combustion. As a result of these strategies, carbon monoxide and hydrocarbon emissions were reduced. Soot emission was slightly increased with retarded pilot injection timing while the effect of pilot injection on nitrogen oxides emission was negligible under low combustion temperature condition. Spatial distribution of fuel from the spray targeting visualization was also investigated to provide more insight into the reason for the reduction in carbon monoxide and hydrocarbon emissions.