• 한국산업융합학회 논문집
• /
• 제9권1호
• /
• pp.21-27
• /
• 2006

The laminar burning velocity was measured using a spherical combustion bomb with central ignition. Mixtures with equivalence ratio between 0.6 and 1.2, were tested. The computation was carried out for the burning velocity using premix code of Chemkin program under the unburned gas pressure of 0.5bar-30bar and temperature of 300K-700K at ${\Phi}1.0$. The results showed little difference between these two methods. The burning velocity was decreased by increasing the pressure and increased by increasing the temperature. The burning velocity was predicted by using the following equations $$S_L(m/s) = S_{st}(T/300)^{1.85}(P)^{-0.45}$$ $$(0.5bar{\leq}P{\leq}30bar,\;300K{\leq}T{\leq}700K)$$).

• International Journal of Automotive Technology
• /
• 제7권1호
• /
• pp.1-7
• /
• 2006

The ignition delay of a dual fuel system has been numerically investigated by adopting a constant volume chamber as a model problem simulating diesel engine relevant conditions. A detailed chemical kinetic mechanism, consisting of 28 species and 135 elementary reactions, of dimethyl ether (DME) with methane ($CH_{4}$) sub-mechanism has been used in conjunction with the multi-dimensional reactive flow KIVA-3V code to simulate the autoignition process. The start of ignition was defined as the moment when the maximum temperature in the combustion vessel reached to 1900 K with which a best agreement with existing experiment was achieved. Ignition delays of liquid DME injected into air at various high pressures and temperatures compared well with the existing experimental results in a combustion bomb. When a small quantity of liquid DME was injected into premixtures of $CH_{4}$/air, the ignition delay times of the dual fuel system are longer than that observed with DME only, especially at higher initial temperatures. The variation in the ignition delay between DME only and dual fuel case tend to be constant for lower initial temperatures. It was also found that the predicted values of the ignition delay in dual fuel operation are dependent on the concentration of the gaseous $CH_{4}$ in the chamber charge and less dependent on the injected mass of DME. Temperature and equivalence ratio contours of the combustion process showed that the ignition commonly starts in the boundary at which near stoichiometric mixtures could exists. Parametric studies are also conducted to show the effect of additive such as hydrogen peroxide in the ignition delay. Apart from accurate predictions of ignition delay, the coupling between multi-dimensional flow and multi-step chemistry is essential to reveal detailed features of the ignition process.

• 한국화재소방학회논문지
• /
• 제22권5호
• /
• pp.72-78
• /
• 2008

본 연구에서는 EPS 샌드위치 패널 심재에 대한 일정한 외부 복사열에 의한 질량감소속도와 열방출특성을 분석하였다. 일정한 외부 복사열원에 노출된 EPS 샌드위치 패널 심재의 질량감소속도와 열방출특성을 분석하기 위해 3가지 Type의 시료를 사용하였으며, 연소열을 측정하기 위해 Oxygen bomb calorimeter를 질량감소속도와 열방출특성을 분석하기 위해 Mass loss calorimeter를 사용하였다. 질량감소속도와 열방출 특성을 분석하기 위해 $100mm{\times}100mm{\times}50mm$ 크기의 시료를 사용하였다. 연구결과 50 kW/$m^2$의 외부복사열원에서 평균질량감소속도는 Type A와 B의 경우 각각 2.7 g/$m^2s$, 2.8 g/$m^2s$로 비슷한 경향을 나타낸 반면, Type C는 2.3 g/$m^2s$로 상대적으로 낮게 나타났으며, 평균열방출속도는 Type B와 C의 경우 각각 47.19 kW/$m^2$, 50.06 kW/$m^2$으로 큰 차이가 없었으나, Type A는 58.23 kW/$m^2$으로 상대적으로 높게 나타났다. 열방출특성의 결과를 캐나다 분류체계에 적용할 경우 Type A와 C의 경우 C-3등급, Type B의 경우 C-2등급으로 분류되었다. 향후 콘칼로리미터법을 이용한 샌드위치 패널 심재에 대한 열방출율 특성과의 비교연구가 필요할 것으로 판단된다.

• Environmental Engineering Research
• /
• 제23권3호
• /
• pp.250-257
• /
• 2018

We developed new composites by combining the solid waste from Low-Density Polyethylene in the form of plastic bag (PB) and biomass from rice husk (RH),in the form of $(RH)_x(PB)_{1-x}$ (x = (1, 0.9, 0.7, 0.5)), as alternative fuels for electrical energy sources, and for providing the best solution to reduce environmental pollution. Elemental compositions were obtained by using proximate analysis, ultimate analysis, and X-ray fluorescence spectroscopy, and the thermal characteristics were obtained from thermogravimetric analysis. The compositions of carbon and hydrogen from the ultimate analysis show significant increases of 20-30% with increasing PB in the composite. The activation energy for RH is 101.22 kJ/mol; for x = 0.9 and 0.7, this increases by 4 and 6 magnitude, respectively, and for x = 0.5, shows remarkable increase to 165.30 kJ/mol. The range of temperature of about $480-660^{\circ}C$ is required for combustion of the composites $(RH)_x(PB)_{1-x}$ (x = (1, 0.9, 0.7, 0.5)) to perform the complete combustion process and produce high energy. In addition, the calorific value was determined by using bomb calorimetry, and shows value for RH of 13.44 MJ/kg, which increases about 30-40% with increasing PB content, indicating that PB has a strong effect of increasing the energy realized to generate electricity.

• 한국추진공학회지
• /
• 제22권2호
• /
• pp.66-73
• /
• 2018

밀폐용기 내 Zirconium/Potassium Perchlorate의 연소를 수치적 모델링을 통해 전산해석을 수행하였다. 5차 WENO 공간차분법과 improved delayed detached eddy (IDDES) 난류모델을 사용하여 충격파가 동반되는 내부 유동구조를 모사하였고, 라그랑지안 연소모델을 통해 화약 입자를 계산하였다. 옆면 중앙에 센서가 설치된 원통형 밀폐용기 내부 유동분석을 통해 압력 진동이 발생하는 원인을 규명하였다. 또한 센서 다이어프램 깊이 변화에 따라 측정되는 압력 데이터를 실험값과 비교분석 하였다. 그 결과 센서 탭의 깊이가 약 2.36 mm 이상으로 커지면 유동속도가 아음속으로 감쇠하고 복잡한 eddy가 발생하여 측정값에 큰 불규칙성을 야기하는 현상을 관측하였다.

• 한국지하수토양환경학회지:지하수토양환경
• /
• 제18권1호
• /
• pp.112-122
• /
• 2013

Current status of soil contamination with fluorine and its source were investigated. The basic principles and procedures of various techniques for the analysis of fluorine contents in soil and solid phase samples were summarized in this review. Analysis of fluorine in solid matrices can be achieved by two types of techniques: (i) UV/Vis spectrophotometer or ion selective electrode (ISE) analysis after performing appropriate extraction steps and (ii) direct solid analysis. As the former cases, the standard method of Korean ministry of environment, alkali fusion-ISE method, pyrohydrolysis, oxygen bomb combustion, aqua regia digestion-automatic analysis, and sequential extraction-ISE method were introduced. In addition, direct analysis methods (i.e., X-ray fluorescence spectrometry and proton induced gamma-ray emission spectrometry) and atomic spectrometry combining with the equipment for introducing solid phase sample were also reviewed. Fluorine analysis techniques can be reasonably selected through site-specific information such as matrix condition, contamination level, the amount of samples and the principles of various methods for the analysis of fluorine presented in this review.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2005년도 제25회 추계학술대회논문집
• /
• pp.433-436
• /
• 2005

착화기 및 Can 형태의 점화기를 대기압 이하의 압력에서 사용할 때 나타나는 연소현상과 이에 따른 문제점에 대해서 연구를 수행하였다. 착화기 및 점화기가 일정 수준 이상의 진공도에서 작동할 때 최초 연소화염이 정상적으로 연소하지 못할 수 있으며, 경우에 따라서 점화에 완전히 실패할 가능성도 있는 것으로 나타났다. 이러한 현상은 점화된 상태로 분출된 점화제가 자유체적(free volume)내의 낮은 압력에 노출되면서 화약의 연소성이 급격히 떨어져서 나타난 것으로 점화기 내에서 연소상태로 분출된 가스가 자유체적 내에서 초기에 가능한 높은 압력을 형성하도록 하여 개선할 수 있음이 확인되었다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 제33회 추계학술대회논문집
• /
• pp.149-152
• /
• 2009

파이로스타터는 일종의 가스발생기로써, 내부에 충전되는 저온 고체 추진제의 연소가스를 통해 시동에 필요한 에너지를 터빈에 공급한다. 파이로스타터의 연소관에 충전된 저온 고체추진제를 연소시키기 위한 초기 에너지를 공급해 주기 위해서는 파이로스타터 및 고체추진제의 특성과 형상에 맞는 점화기 설계가 필요하다. 이에 C.B.T 시험을 수행하여 초기 연소실 내부의 충분한 압력 증가를 확보할 수 있는 점화기의 주요 설계 인자를 결정하였다. 파이로스타터의 연계연소시험을 통해 신뢰성 있는 점화 특성을 확인하였고, 점화장약 충전량에 대한 간단한 해석을 수행하였다.

• 한국자동차공학회논문집
• /
• 제10권6호
• /
• pp.72-79
• /
• 2002

The main objective of this study is to investigate the relationship between chemical structure and higher heating value of reformed diesel fuels by ultrasonic irradiation. In order to analyze the chemical structure changes of the reformed diesel fuels by ultrasonic irradiation, Proton nuclear magnetic resonance spectrometer(1H-NMR) was used and to analyze the effect of higher heating values of these diesel fuels, the bomb calorimeter was used. From the study, following conclusive remarks can be made. 1) The aromatic carbon percentages and higher heating values of the reformed diesel fuels by ultrasonic irradiation increased more than the conventional diesel ones. 2) The aromatics percentages and Branch Index(BI) of the reformed diesel fuels by ultrasonic irradiation decreased more than the conventional diesel ones. 3) The higher heating values on both for conventional fuel and reformed diesel fuels by ultrasonic energy irradiation is directly proportional to aromatic carbon percentages and inversely proportional to aromatic percentages and BI for these fuels.

• 한국자동차공학회논문집
• /
• 제18권6호
• /
• pp.53-62
• /
• 2010

An airbag is composed of housing assembly, door assembly, cushion assembly, and an inflator. The inflator is the essential part that generates gas for airbag. When an airbag is activated, it effectively absorbs the crash energy of the passenger by inflating a cushion. In this study, tank tests were performed with newly synthesized propellants with various compositions, and the results are compared with the numerical results. In the simulation of inflator, a zonal model has been adopted which consisted of four zones of flow regions: combustion chamber, filter, gas plenum, and discharge tank. Each zone was described by the conservation equations with specified constitutive relations for gas. The pressure and temperature of each zone of the inflator were calculated and analyzed and the results were compared with the tank test data. In the zone of discharge tank the pressure quickly rose, the pattern of pressure curve was very similar to the pressure curve of real test. And in zone 1 & 2 & 3 the mass of products was increased and decreased with time. In zone 4, the mass of products was increased with time like real inflator. From the similarity of pressure curve in zone 4 and closed bomb calculation the modeled results are well correlated with the experimental values.