• Journal of Institute of Control, Robotics and Systems
• /
• v.12 no.11
• /
• pp.1119-1123
• /
• 2006

The flame image processing and analysis system has been investigated for the optimal pulverized coal firing of thermal power plant, especially for lower nitrogen oxide generation and more safe operation. We aimed at gaining the relationship between burner flame image information and emissions of nitrogen oxide and unburned carbon in furnace utilizing the flame image processing methods, by which we quantitatively determine the condition of combustion on the individual humors. Its feasibility test was undertaken with a pilot furnace for coal firing, through which the system was observed to be effective for the monitoring of the combustion condition of pulverized coal firing boilers.

• International Journal of Automotive Technology
• /
• v.6 no.4
• /
• pp.341-350
• /
• 2005

In this study, fault diagnosis and monitoring of serial wound pre-engaged starter motors have been carried out. Starter motors are DC motors that enable internal combustion engine (ICE) to run. In case of breakdown of a starter motor, internal combustion engine can not be worked. Starter motors have vital importance on internal combustion engines. Kohonen network based fault diagnosis system is proposed for fault diagnosis and monitoring of starter motors. A graphical user interface (GUI) software has been developed by using Visual Basic 6.0 for fault diagnosis. Six faults, seen in starter motors, have been diagnosed successfully by using the developed fault diagnosis system. GUI software makes it possible to diagnose the faults in starter motors before they occur by keeping fault records of past occurrences.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.10a
• /
• pp.607-610
• /
• 2009

The abnormal combustion in the running engine results to knocking which increases the pressure and temperature in the cylinder, thereby decreasing the generated power by reducing the thermal efficiency. When the temperature and pressure in the cylinder increased rapidly by knocking, abnormal combustion takes place and the engine power is decreased. To investigate the knocking phenomenon, accelerometers are installed in the cylinder head to monitor and diagnose the vibration signal. As method of signal analysis, the time-frequency analysis method was adapted for acquisition of vibration signal and analyzes engine combustion in the short time. In this experiment, after analyzing time data which is stored in the signal recorder in one unit work (4 strokes: 2 revolutions), the signal with frequency and Wavelet methods with extracted one engine combustion data was also analyzed. Then, normal condition with no knocking signal is analyzed at this time. Hereafter, the experiments made a standard for distinguishing normal and abnormal condition to be carried out in acquisition of vibration signal at all cylinders and extracting knocking signal. In addition, analyzing methods can be diverse with Symmetry Dot Patterns (SDP), Time Synchronous Average (TSA), Wigner-Ville Distribution (WVD), Wigner-Ville Spectrum (WVS) and Mean Instantaneous Power (MIP) in the cold test [2]. With signal processing of vibration from engine knocking sensor, the authors adapted a part of engine /rotor vibration analysis and monitoring system for marine vessels to prevent several problems due to engine knocking

• Journal of Institute of Control, Robotics and Systems
• /
• v.3 no.3
• /
• pp.318-322
• /
• 1997

A prototype of combustion zone monitoring system as been developed and installed into tuyeres of the blast furnace. The system consists of CCD(charge coupled device) cameras, sonic flow meters, an image processor and a personal computer. The personal computer collects raceway luminance data and operational data from the image processor that is connected to the color CCD camera from the blast furnace process computer, respectively. In addition, the sonic flow meters supply coal injection rate data to the personal computer. Then, the personal computer evaluates the combustion conditions with the raceway inspection algorithm. This integrated monitoring system allows us to detect abnormal raceway conditions and the clogging status of coal injection pipe. The image processing techniques of the system enable us to effectively monitor unburnt coal sticking to tuyere tip and injection lance wear conditions. Such a developed system ensures rapid and precise raceway inspection. The image processing capability of the system has helped operator to early detect both the unburnt coal sticking problem and the errosion problem of injection lance. Furthermore, the system could control the abnormal raceway condition based the the analysis results obtained from combustion monitoring.

• Journal of the Korean Society of Tobacco Science
• /
• v.33 no.1
• /
• pp.28-38
• /
• 2011

This experiment was conducted as a part of Asia collaborative study on purpose of verifying the difference between CM6 and CM7 including 3R4F for reference. It carried out using various analytical categories for example, main stream, sidestream and Av. smoke. Additional analysis such as physical properties, blending ratio, combustibility and general leaf component analysis also implemented in order to investigate the difference. We complied with ISO standard and CORESTA recommended method during analytical operating procedures. In this study, we described that comparative analytical result for CM6 and CM7 known as reference or monitoring cigarettes including 3R4F for reference. All sample cigarettes were conditioned at $22^{\circ}C$, 60% relative humidity for 48 hours. Av. Smoke, MS and SS smoke analysis were performed over five times with two smoking condition, ISO and Health Canada with the exception of Av. smoke analysis. We complied with ISO standard method during analytical operating procedures. And, we conducted additional analysis, such as physical properties, blending ratio, combustibility and leaf component analysis also in order to investigate the difference. In conclusion, we found out some differences between CORESTA monitoring cigarette No. 6 and No 7. The smoke components such as total particulate matters, NFDPM, nicotine and carbon monoxide contents of CM7 were a little lower than CM6. And, these phenomena were the same as not only main stream smoke but also side stream smoke and Av. smoke. This tendency was consistent with ISO and Health Canada smoking condition. Besides, leaf constituents' color of CM7 was darker than CM6. In case of combustibility, it showed short combustion time approximately 30 seconds.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.6
• /
• pp.674-680
• /
• 2014

Monitoring systems of informations for ship performance have become important gradually for economical management of existing ship. Monitoring of NOx emission from marine diesel engines is one of them. The measurement of NOx emission, however has been many difficulties due to technical and costly problems. A monitoring by prediction method of NOx on-board ship according to sailing condition of ship could be an useful method. In this paper, it is discussed about modified method of one-zone model which has been utilized usually for analyzing the combustion process. The modified method is able to calculate the temperature of burned region from the result by one-zone model. Influences which excess air ratio during combustion process affected for the gas temperature and NOx emission were investigated. From the results variation of excess air ratio during combustion process could be estimated inversely through the comparison with measurement of NOx emission.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.3
• /
• pp.67-72
• /
• 2011

Turbine blades operate under high temperature and pressure. The influence changes according to its width and angle. Thermal stress and pressure are important factors to analyze the stress distribution. The purpose of this study is to investigate the effects of loads on the gas turbine blade using thermal stress analysis. These analysis results show the gas fluid flow with a high pressure around the surface of blade. Gas temperature is related to the pressure of flow around the blade. The stress concentration around blade is shown and the concentration is due to the difference between suction side and pressure side of combustion gas.

• The Journal of Korea Robotics Society
• /
• v.17 no.4
• /
• pp.477-483
• /
• 2022

In this paper, we propose waste collection vehicle system with a safety device for worker safety and an autonomous driving function. The steering system is applied as MDPS (Motor Drive Power Steering) system to control the waste collection vehicle of the internal combustion engine. Safety-related errors is prevented through redundancy brake of the integrated system and the control braking system. In order to ensure safety between workers and waste collection vehicles, work guidelines and safety devices for emergency stop in case of danger are applied to vehicles. In addition, this research is conducted on improving the working efficiency through vehicle condition monitoring system and a short-range control system for field test. This research is aimed to secure stability through demonstration and contribute to the industrialization of unmanned waste collection vehicles.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.14 no.1
• /
• pp.16-22
• /
• 1994

In contrast to the machineries using rolling element bearings, systems with journal bearings generally operate in large scale and under severe loading condition such as steam generator turbines and internal combustion engines. Failure of the bearings in these machineries can result in the system breakdown. To avoid the time consuming repair and considerable economic loss, the detection of incipient failure in journal bearings becomes very important. In this experimental approach, acoustic emission monitoring is applied to the detection of incipient failure caused by several types of abnormal operating condition most probable in the journal bearing systems. It has been known that the intervention of foreign materials, insufficient lubrication and misassembly etc. are principal factors to cause bearing failure and distress. The experiment was conducted under such designed conditions as hard particles in the lubrication layer, insufficient lubrication, and metallic contact in the simulated journal bearing system. The results showed that acoustic emission could be an effective tool to detect the incipient failure in journal bearings.

• Journal of Advanced Navigation Technology
• /
• v.15 no.1
• /
• pp.18-24
• /
• 2011

This paper proposes fault diagnosis system which is able to diagnose the fault from present operating condition by analyzing monitored signals with present ship monitoring system without additional sensors. For this all kinds of ship's engine room monitored data are classified with combustion subsystem, heat exchange subsystem and electric motor and pump subsystem by analyzing ship's operation data. To extract dynamic characteristics of these subsystems, log book data of container ship of H shipping company are used.