• 한국가스학회지
• /
• 제2권1호
• /
• pp.28-39
• /
• 1998

본 연구에서는 $20\%$ 천장개구부가 있는 정사각형 밀폐공간내의 순수자연대류와 자연대류 -복사가 고려된 복합열전달을 순차해석과 실험을 통하여 비교 분석하였다. 수치해석은 순수자연대류에 대하여 SIMPLE 알고리즘을 사용하였고, 복사열전달에 대해서는 S-N 구분 종좌표법을 이용하였으며 난류유동의 경계조건은 벽함수를 적용하였다. 실험은 수치해석의 결과와 비교하기 위하여 동일한 조건에 대하여 수행되었다. 그 결과 순수자연대류와 복합열전달의 유동장, 온도장의 형상은 유사한 유선함수를 보이고 있으며, 유동가시화를 통한 실험결과와 잘 일치하고 있음을 보여준다. 수치해석과 실험의 온도분포를 비교한 결과 평균 $8.5\%$의 오차를 보였다.

• 설비공학논문집
• /
• 제11권2호
• /
• pp.236-243
• /
• 1999

Aluminum/Freon-22 heat pipes were manufactured and tested which have a special wick geometry combining axial groove and screen mesh. There were 14 axial grooves in a cross-section and these were covered by two layers of 350 mesh screens to enhance the thermal performance. The performance test was conducted by varying the thermal load and tilt angle. Furthermore, the operation limits and overall heat transfer coefficient were investigated. The experimental results will be useful in a variety of applications, especially in design and manufacturing of a high-efficiency heat exchanger and energy recovery systems.

• 대한기계학회논문집B
• /
• 제24권6호
• /
• pp.870-879
• /
• 2000

An experimental investigation is conducted to improve a slot film cooling system which can be used for the cooling of gas turbine combustor liner. The tangential slots are constructed of discrete holes with different injection types which are the parallel, vertical, and combined to the slot lip. The investigation is focused on the coolant supply systems of normal-, parallel-, and counter-flow paths to the mainstream direction. A naphthalene sublimation technique has been employed to measure the local heat/mass transfer coefficients in a slot with various injection types and coolant feeding directions. The velocity distributions at the exit of slot lip for the parallel and vertical injection types are fairly uniform with mild periodical patterns with respect to the hole positions. However, the combined injection type increases the nonuniformity of flow distribution with the period equaling twice that of hole-to-hole pitch due to splitting and merging of the ejected flows. The secondary flow at the lip exit has uniform velocity distributions for the parallel and vertical injection types, which are similar to the results of a two-dimensional slot injection. In the results of local heat/mass transfer coefficient, the best cooling performance inside the slot is obtained with the vertical injection type among the three different injection types due to the effect of jet impingement. The lateral distributions of Sh with the parallel- and counter-flow paths are more uniform than the normal flow path. The averaged Sh with the injection holes are $2{\sim}5$ times higher than that of a smooth two-dimensional slot path.

• 에너지공학
• /
• 제14권2호
• /
• pp.98-104
• /
• 2005

Pannier-arrangement condensers are usually adopted in the turbine generator units of combined cycle power plants. Optimization of operating performance and economy is an important goal, which requires accurate understanding of flow and heat transfer effects in the condenser. The tube bundle arrangement and steam flow behaviors of pannier-arrangement condensers are very different from those of common condensers. The physical model for existing numerical simulation program of condenser is refined by constructing the correlations for flow resistance and condensation heat exchange coefficient in which the influences of steam flow direction are considered according to available experimental data. The adaptability of the developed physical model and simulation program of pannier-arrangement condenser is verified with available experimental data.

• 한국산업융합학회 논문집
• /
• 제8권2호
• /
• pp.105-112
• /
• 2005

The characteristics of natural convection heat transfer combined with radiation in a vertical parallel plates has been investigated experimentally. The vertical channel is consisted with a heated wall and three protruding heating sources attached on the opposite wall. The cooling of modules has been experimented with heating the wall as well as modules themselves at different aspects ratios and heating fluxes. As the location of module is higher, the temperature becomes higher, but the increasement is smaller. When the aspect ratio is lower than 26, its effect on the temperature is not significant rather than that of the radiation heat transfer. Furthermore, the correlation of Nusselt number with the Rayleigh number are attempted, but additional treatment is needed to accomodate the cases of heating module and/or opposite wall.

• 대한기계학회논문집B
• /
• 제41권11호
• /
• pp.719-726
• /
• 2017

튜브 피치와 주변 튜브의 열유속이 수평으로 설치된 튜브 배열의 풀비등 열전달에 미치는 영향을 살펴보기 위하여 실험적 연구를 수행하였다. 실험을 위하여 외경이 19 mm인 두 개의 스테인리스강 튜브와 대기압 상태인 물을 사용하였다. 튜브간 피치는 18.5~95 mm이며, 주변 튜브의 열유속은 $0{\sim}90kW/m^2$이다. 열전달 향상은 주변 튜브의 열유속이 크고 시편의 열유속이 $40kW/m^2$보다 낮은 경우에 분명하게 관찰되었다. 피치가 튜브 지름의 4배 보다 크면 피치 변화가 열전달에 미치는 영향은 무시할 수 있을 정도이다. 순환유동, 대류유동, 액체교란은 열전달을 향상시키며 유동간섭과 기포군집은 열전달을 둔화시킨다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 추계학술발표대회 개요집
• /
• pp.135-137
• /
• 2005

The body of the work covers FSW welding of Al6061 and its thermal distribution based on an analytical model for the heat input at the probe/matrix boundary of Al plates and FSW tool due to the effect of combined translation and rotational motion of the tool pin and shoulder. Finally the 2D- finite element heat transfer analysis program has been used to plot the heat distribution at the Friction Stir Welded joint in Al 6061 plate. The work concludes that the heat distribution result obtained from FE analysis has a reasonable agreement with the experimentally measured values.

• 에너지공학
• /
• 제26권1호
• /
• pp.9-22
• /
• 2017

A combined thermal and flow analysis was carried out to study the behavior and performance of a small, commercial LTD (Low-Temperature-Differential) heat engine. Laminar-flow solutions for annulus and channel flows were employed to estimate the viscous drags on the piston and the displacer and the pressure difference across the displacer. Temperature correction factors were introduced to account for the departure from the ideal heat transfer processes. The analysis results indicate that the work required to overcome the viscous drags on engine moving parts and to move the displacer is much smaller than the moving-boundary work produced by the power piston for temperature differentials in the neighborhood of $20^{\circ}C$ and engine speeds below 10 RPS. A comparison with experimental data reveals large degradations from the ideal heat transfer processes. Thus, heat-transfer devices inside the displacer cylinder are recommended.

• 대한기계학회논문집
• /
• 제14권6호
• /
• pp.1652-1660
• /
• 1990

본 연구에서는 원관내에서 복사에 관여하는 고온의 가스유동에 의한 복사열전 달과 대류열전달간의 상호작용에 대해 실험과 수치해석을 통하여 고찰하고자 한다. 실험으로는 프로판가스의 화염생성에 의한 속도, 온도 및 벽면에서의 열유속분포를 측 정하고, 수치적으로는 냉염(cold flame) 상태서 측정한 난류요동성분과 연소시의 입구 속도와 온도를 초기조건으로 하여 밀도와 점성계수의 온동에 따른 변화를 고려한 K-.epsilon. 모델과 구조화근사법 및 최근에 개발되어 사용되기 시작한 Weighted Sum of Gray Gas- es모델을 사용하여 속도, 온도 및 열유속 분포를 계산하여 수치해석의 결과와 실험결 과를 비교함으로써 모델의 타당성을 검증하고, 복사에 의한 열전달량과 대류에 의한 열전달량을 분리하여 각 모드가 온도분포 및 열유속분포에 미치는 영향을 고찰하고자 한다.

• 대한기계학회논문집B
• /
• 제35권9호
• /
• pp.923-932
• /
• 2011

본 연구에서는 복합화력발전소 가스터빈 출구가스 안내덕트 내부의 가스유동장이 배열회수보일러 전열기구에 미치는 영향을 CFD기법을 이용하여 분석하였다. 안내덕트 내부 난류흐름의 경우, 유속의 편차가 크고 선회 효과 및 상승류 현상이 심한 특징을 가지고 있음으로 이와 같은 유동의 수치해석을 위해 2개 방정식 난류점성 모델 중 RNG k-${\epsilon}$ 모델을 사용하였으며 유동장의 영향을 가장 많이 받는 배열 회수보일러 최종과열기관의 열전달특성변화를 파악하기 위하여 NTU 방식을 이용한 수치해석결과와, 산업계에서 적용하는 설계기법에 의한 결과를 비교하였다.