• Earthquakes and Structures
• /
• 제7권5호
• /
• pp.705-718
• /
• 2014

This paper presents an analytical model for determining the transverse reinforcement required for reinforced concrete exterior beam-column joints subjected to reversed cyclic loading. Although the joint aspect ratio can affect joint shear strength, current design codes do not consider its effects in calculating joint shear strength and the necessary amount of transverse reinforcement. This study re-evaluated previous exterior beam-column joint tests collected from 11 references and showed that the joint shear strength decreases as the joint aspect ratio increases. An analytical model was developed, to quantify the transverse reinforcement required to secure safe load flows in exterior beam-column joints. Comparisons with a database of exterior beam-column joint tests from published literature validated the model. The required sectional ratios of horizontal transverse reinforcement calculated by the proposed model were compared with those specified in ACI 352R-02. More transverse reinforcement is required as the joint aspect ratio increases, or as the ratio of vertical reinforcement decreases; however, ACI 352R-02 specifies a constant transverse reinforcement, regardless of the joint aspect ratio. This reevaluation of test data and the results of the analytical model demonstrate a need for new criteria that take the effects of joint aspect ratio into account in exterior joint design.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계학술발표회 논문집(I)
• /
• pp.30-33
• /
• 2006

The purpose of this research is to study the seismic behavior of interior column-slab connections with different column aspect ratio, when subjected to combined gravity and cyclic lateral loading. The control specimen had square column, while the other specimens had rectangular column with aspect ratio of 0.5 and 2.0. From the test results, all of the specimens sustain lateral drifts as high as 4% with no more than a 20% decrease in peak lateral load capacity. And it appears that KBC Code(2005) procedure may be unconservative for connections with different column aspect ratio.

• 한국구조물진단유지관리공학회 논문집
• /
• 제11권1호
• /
• pp.121-129
• /
• 2007

본 연구는 플랫 플레이트 구조에서 직사각형 외부기둥-슬래브 접합부의 뚫림전단강도에 관한 실험결과에 관하여 다룬다. 직사각형 기둥의 형상비 증가에 따른 뚫림전단거동을 평가하기 위해 위험단면의 길이를 일정한 값이 되도록 기둥 단면크기를 산정하고 총 8개의 실험체를 계획하였다. 두 수준의 콘크리트 압축강도($f^{\prime}_c=24$, 40MPa)에 대하여 기둥단면의 형상비(${\beta}_c=C_1$/$C_2=2.0{\sim}4.5$)와 슬래브 철근비가 변수에 포함된다. 실험결과 기둥의 형상비가 증가할수록 뚫림전단강도는 감소하였고 형상비 증가에 따른 뚫림전단강도 감소율은 점차로 작게 나타났다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.85-88
• /
• 1995

Recently, the micro mold maching techining technology is developed by means of the mechanical and high energy beam process. It is possible to make the micro structure mold with high aspect ratio by the LIGA technology. This mode is used for mass production of plastic parts by the micro injection molding method. In this study, we intend to research on the basic technology of micro injection molding. As the result, we developed the injection molding technology for small column plastic parts which diameter is 500 .mu. m and 200 .mu. m respectively with wbout aspect ratio 20.

• 한국구조물진단유지관리공학회 논문집
• /
• 제12권5호
• /
• pp.74-80
• /
• 2008

본 논문은 기둥형상비를 실험 변수로 가지는 무량판 슬래브-기둥 접합부의 내진성능을 평가하는데 있다. 본 연구에서는 무량판 슬래브의 뚫림 전단파괴를 방지하기 위하여 본 연구와 병행하여 진행된 연구에서 개발된 연속 절곡된 전단보강근을 적용하였다. 기둥형상비에 따른 실험체는 각각 FIS1-05(0.5), FIS1- 10(1.0), FIS1-20(2.0) 이다. 실험체의 수평방향으로 정적 수평하중을 가력 하였으며, 중력하중비에 의한 일정 수직 하중을 적용하였다. 실험결과는 슬래브-기둥 접합부의 수평 변위 및 강도를 기준으로 평가하였다. 분석결과, FIS1-05, FIS1-20와 같은 장방형 기둥을 갖는 접합부의 성능이 FIS1-10와 같은 정방형 기둥을 갖는 접합부보다 우수한 것으로 평가되었다.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제9권3호
• /
• pp.326-338
• /
• 2017

The Vortex-induced Motions (VIM) phenomenon of semi-submersibles is relevant for the fatigue life of moorings and risers. Model tests regarding the VIM behavior of a semi-submersible with four square columns were conducted in order to investigate the effects of the current incidence and the aspect ratio of the immerged column. The experimental results show that the largest transverse amplitudes are around 70% of the column width at $30^{\circ}$ and $45^{\circ}$ incidences in a range of reduced velocities from 5 to 8 when the aspect ratio of the immerged column is 1.90. The largest yaw motion occurs at $0^{\circ}$ incidence with the peak value around $4.5^{\circ}$. Similar characteristics of the VIM response are observed for the semi-submersible with aspect ratios of 1.90 and 1.73. When the aspect ratio decreases 50% to 0.87, 30% decrease in the peak transverse amplitudes can be seen.

• Structural Engineering and Mechanics
• /
• 제41권1호
• /
• pp.43-65
• /
• 2012

The primary objective of this study was to identify concrete contribution to the initial shear strength of reinforced concrete (RC) hollow columns under lateral loading. Seven large-scale RC rectangular hollow column specimens were tested under monotonic or cyclic lateral loads. The most important design parameter was column length-to-depth aspect ratio ranging between 1.5 and 3.0, and the other test variables included web area ratio, hollow section ratio, and loading history. The tests showed that the initial shear strength reduced in a linear pattern as the column aspect ratio increased, and one specimen tested under cyclic loading achieved approximately 83% of the shear strength of the companion specimen under monotonic loading. Also, several pioneering shear models proposed around the world, all of which were mainly based on tests for columns with solid sections, were reviewed and compared with the test results of this study, for their possible applications to columns with hollow sections. After all, an empirical equation was proposed for concrete contribution to the initial shear strength of RC hollow columns based on fundamental mechanics and the test results.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 춘계 학술발표회 제20권1호
• /
• pp.53-56
• /
• 2008

본 연구는 주거용 고층 건물에서 폭넓게 사용되고 있는 플랫 플레이트 구조에서 장방형 기둥-슬래브 접합부를 대상으로 실시한 6개의 실험결과를 분석한 것이다. 연구의 목적은 지진하중과 같이 반복적으로 작용하는 횡하중에 대하여 기둥 단면의 형상비(${\beta}$c=$c_1/c_2$)에 따른 접합부의 이력거동을 비교 평가 하는 것이다. 기둥 형상비는 $b_o$가 일정해 지도록 0.33${\sim}$3($c_1/c_2$=1/3, 1/1, 3/1)으로 선정하였다. 슬래브 휨철근비는 1.0%, 1.5%로 변화시켰으며, 중력전단력비($V_g/V_c$) 등 접합부의 이력거동에 영향을 줄 수 있는 다른 영향인자들은 일정한 조건으로 계획하여 기둥 형상비의 영향을 고찰할 수 있도록 하였다. 실험을 통해서 뚫림전단파괴 양상과 균열 패턴, 접합부의 강성, 변형능력 등을 변수에 따라 분석하였다.

• 콘크리트학회논문집
• /
• 제29권1호
• /
• pp.77-84
• /
• 2017

본 연구에서는 고강도 콘크리트 기둥-일반강도 콘크리트 슬래브 접합부의 구속도, 형상비 (h/c), 강도비 ($f^{\prime}_{cc}/f_{cs}$)에 따른 구조거동 분석하였다. 유한요소해석 프로그램을 통해 해석적 연구가 수행되었으며, 해석 방법의 검증을 위하여 기존의 구조 실험과 동일한 조건의 해석 부재를 제작하여 결과를 비교하였다. 부재의 종류는 내부기둥, 외부기둥, 모서리기둥, 독립기둥으로 분류하였으며 내부기둥에서 가장 높은 극한강도를 보였다. 또한 형상비가 증가할수록 접합부에 작용하는 축방향 응력이 작게 나타났으며 강도비가 증가할수록 부재의 극한강도가 상승하였으나 1.83이후로는 뚜렷한 강도 증진을 나타내지 않았다.

• 대한기계학회논문집
• /
• 제11권4호
• /
• pp.629-636
• /
• 1987

An experiment is carried out to study the surface-tension driven flow characteristics in a cylindrical liquid column heated from above (which is the low gravity floating zone simulated on earth) with varing the aspect ratio and diameter of the liquid column. Hexadecane, octadecane, silicon oil(10cs), FC-40 and water are used as the test liquids. The free surface shape varies sinusoidally for Ma>M $a_{cr}$ and its frequency is found to be the same as that of temperature oscillation. It is verified that the surface temperature profile changes from linear to S-shaped profile for Ma>M $a_{cr}$ . The frequency of temperature oscillation decreases with increasing liquid volume, while its level increases. M $a_{cr}$ decreases with increasing aspect ratio, and also decreases with increasing Prandtl number in the range of 25