• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.12 no.2
• /
• pp.58-65
• /
• 2016

Since, in case of high energy piping, steam jets ejected from the rupture zone may cause damage to nearby structure, it is necessary to design it into consideration of nuclear power plant design. For the existing nuclear power plants, the ANSI / ANS 58.2 technical standard for high-energy pipe rupture was used. However, the US Nuclear Regulatory Commission (USNRC) and academia recently have pointed out the non-conservativeness of existing high energy pipe fracture evaluation methods. Therefore, it is necessary to develop a highly reliable evaluation methodology to evaluate the behavior of steam jet ejected during high energy pipe rupture and the effect of steam jet on peripheral devices and structures. In this study, we develop a method for analyzing the impact load of a jet by high energy pipe rupture, and plan to carry out an experiment to verify the evaluation methodology. In this paper, the basic data required for the design of the jet impact load experiment equipment under construction, 1) the load change according to the jet distance, 2) the load change according to the jet collision angle, 3) the load variation according to structure diameter, and 4) the load variation depending on the jet impact position, are numerically obtained using the developed steam jet analysis technique.

• Journal of the Society of Naval Architects of Korea
• /
• v.54 no.6
• /
• pp.470-475
• /
• 2017

Since the intake air of gas turbine engine of marine purpose contains water particles, inertial separator for separating the air and water particles are provided. Saw type and wave type separator are now used to separate inflow water particle from the gas. In this paper, the design parameters of saw type separator are studied by numerical simulations. Using the commercial CFD program, Star-CCM+, Lagrangian-Eulerian method was used to perform the analysis of two phase flow of the mist in the air. This method solves Reynolds-Averaged Navier-Stokes equations in Eulerian framework for the continuous phase, while solves equation of motion for individual particles in Lagrangian framework. Lagrangian multiphase method was applied to monitor the particles of different sizes and shapes and to verify collision between particles by chasing particles. Water particles were injected through injectors located at the inlet of the separator and escape mode was used which assumes that the particles attached on the surface of inertial separator were removed from the simulation, effectively escaping the solution domain. Through the numerical computations with the inlet condition of constant water particle size in the wetness fraction of 85%, efficiency of eliminating the water particle and the pressure drop between the inlet and outlet were examined.

• Journal of Navigation and Port Research
• /
• v.29 no.8 s.104
• /
• pp.661-666
• /
• 2005

Recent warnings indicate that there is a potential risk of massive earthquake. These earthquakes could produce large-scale tsunamis. Consideration of the effect of Tsunami to the moored ship is very important bemuse it brings the loss of life and vast property damage in a viewpoint of ship operations within a harbor. If a tsunami occurs, a ship in a harbor may begin drifting in case of ship entering and departing harbor, and breakage of mooring rope and drifting of moored ship are happened. And extremely serious accident, such as stranding and collision to a quay, might occur. On the other hand, since the tsunami consists of approximately component waves of several minutes, there is a possibility of resonance with the long period motion of mooring vessel. As the speed of Tsunami is much faster than tidal current in a harbor, a strong resisting force might act on the moored ships. In this paper, the numerical simulation procedure in the matter of ship motions due to the attack of large-scale tsunamis are investigated and the effects on the ship motions and mooring loads are evaluated by numerical simulation.

• Transactions on Electrical and Electronic Materials
• /
• v.8 no.1
• /
• pp.5-10
• /
• 2007

Using a reference slurry, ammonium dodecyl sulfate (ADS), an anionic and environmentally friendly surfactant, was investigated as an alternative to BTA for its inhibition and lubrication characteristics. Results demonstrated that the inhibition efficiency of ADS was superior to that of BTA. Coefficient of friction (COF) was the lowest when the slurry contained ADS. This suggested that adsorbed ADS on the surface provided lubricating action thereby reducing the wear between the contacting surfaces. Temperature results were consistent with the COF and removal rate data. ADS showed the lowest temperature rise again confirming the softening effect of the adsorbed surfactant layer and less energy dissipation due to friction. Spectral analysis of shear force showed that increasing the pad-wafer sliding velocity at constant wafer pressure shifted the high frequency spectral peaks to lower frequencies while increasing the variance of the frictional force. Addition of ADS reduced the fluctuating component of the shear force and the extent of the pre-existing stick-slip phenomena caused by the kinematics of the process and collision event between pad asperities with the wafer. By contrast, in the case of BTA, there were no such observed benefits but instead undesirable effects were seen at some polishing conditions. This work underscored the importance of real-time force spectroscopy in elucidating the adsorption, lubrication and inhibition of additives in slurries in CMP.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.6
• /
• pp.1365-1373
• /
• 1994

A Monte-Carlo simulation model, developed to predict size distribution of air bubbles in turbulent shear flow, is applied to a laboratory-scale problem. Sensitivity to various numerical and physical parameters of the model is analyzed. Practical applicability of the model is explored through comparisons of results with experimental measurements. Bubble size increases with air-water discharge ratio and friction factor. Bubble size decreases with increasing mean flow velocity, but the total bubble surface area in the aeration region remains fairly constant. The effect on bubble size distribution of the longitudinal length increment in the simulation model is negligible. A larger radial length increment yields more small and large bubbles and fewer in between. Bubble size distribution is significantly affected by its initial distribution and the location of air injection. Collision efficiency is introduced to explain the discrepancy between collisions with and without coalescence.

• Proceedings of the IEEK Conference
• /
• 2003.07a
• /
• pp.57-60
• /
• 2003

IEEE 802.16 Wireless MAN standard specifies the air interface of fixed point-to-multipoint broadband wireless access systems providing multiple service. Among the service classes supported by the wireless MAN, the BE class is ranked on the lowest position in priority and is usually deployed by multicast and broadcast polling MAC scheme. In provisioning such BE service, the delay performance is influenced by a number of components including restrictions on resource request per SS, the number of request opportunities in upward frame, scheduling requests at BS, and contention resolution method. As candidate components of MAC function for BE service, we propose single and multiple request schemes (for controling the number of requests per SS), exhaustive and limited request schemes (for regulating the amount of grant per request) and FCFS, H-SMF, pure SMF, SS-wise Round Robin, and pure Round Robin (for scheduling requests at BS). Then, we construct MAC schemes by combining the above components and evaluate the delay performance exhibited by each MAC scheme using a simulation method. From numerical results, we investigate the effect of MAC components on average delay and delay variation and observe the dissonance on collision reduction in a resource - limited environment.

• Safety and Health at Work
• /
• v.10 no.4
• /
• pp.461-469
• /
• 2019

Background: Collisions involving workers and mobile machines continue to be a major concern in underground coal mines. Over the last 30 years, these collisions have resulted in numerous injuries and fatalities. Recently, the Mine Safety and Health Administration (MSHA) proposed a rule that would require mines to equip mobile machines with proximity detection systems (PDSs) (systems designed for automated collision avoidance). Even though this regulation has not been enacted, some mines have installed PDSs on their scoops and hauling machines. However, early implementation of PDSs has introduced a variety of safety concerns. Past findings show that workers' trust can affect technology integration and influence unsafe use of automated technologies. Methods: Using a mixed-methods approach, the present study explores the effect that factors such as mine of employment, age, experience, and system type have on workers' trust in PDSs for mobile machines. The study also explores how workers are trained on PDSs and how this training influences trust. Results: The study resulted in three major findings. First, the mine of employment had a significant influence on workers' trust in mobile PDSs. Second, hands-on and classroom training was the most common types of training. Finally, over 70% of workers are trained on the system by the mine compared with 36% trained by the system manufacturer. Conclusion: The influence of workers' mine of employment on trust in PDSs may indicate that practitioners and researchers may need to give the organizational and physical characteristics of each mine careful consideration to ensure safe integration of automated systems.

• Nuclear Engineering and Technology
• /
• v.52 no.2
• /
• pp.397-416
• /
• 2020

Investigations of the commercial aircraft impact effect on nuclear island infrastructures have been drawing extensive attention, and this paper aims to perform the safety assessment of Generation III nuclear power plant (NPP) buildings subjected to typical commercial aircrafts crash. At present Part II, based on the verified finite element (FE) models of aircrafts Airbus A320 and A380, as well as the NPP containment and auxiliary buildings in Part I of this paper, the whole collision process is reproduced numerically by adopting the coupled missile-target interaction approach with the finite element code LS-DYNA. The impact induced damage of NPP plant under four impact locations of containment (cylinder, air intake, conical roof and PCS water tank) and two impact locations of auxiliary buildings (exterior wall and roof of spent fuel pool room) are evaluated. Furthermore, by considering the inner structures in the containment and raft foundation of NPP, the structural vibration analyses are conducted under two impact locations (middle height of cylinder, main control room in the auxiliary buildings). It indicates that, within the discussed scenarios, NPP structures can withstand the impact of both two aircrafts, while the functionality of internal equipment on higher floors will be affected to some extent under impact induced vibrations, and A380 aircraft will cause more serious structural damage and vibrations than A320 aircraft. The present work can provide helpful references to assess the safety of the structures and inner equipment of NPP plant under commercial aircraft impact.

• 한국전산유체공학회:학술대회논문집
• /
• 2007.04a
• /
• pp.83-86
• /
• 2007

Turbulent flow analysis is conducted around the multi-stage launch vehicle including base region and detachment motion of strap-on boosters due to resultant aerodynamic forces and gravity is simulated. Aerodynamic solution procedure is coupled with rigid body dynamics for the prediction of separation behavior. An overset mesh technique is adopted to achieve maximum efficiency in simulating relative motion of bodies and various turbulence models are implemented on the flow solver to predict the aerodynamic forces accurately. At first, some preliminary studies are conducted to show the importance of base flow for the exact prediction of detachment motion and to find the most suitable turbulence model for the simulation of launch vehicle configurations. And then, developed solver is applied to the simulation of KSR-III, a three-stage sounding rocket researched in Korea. From the analyses, after-body flow field strongly affects the separation motions of strap-on boosters. Negative pitching moment at initial stage is gradually recovered and a strap-on finally results in a safe separation, while fore-body analysis shows collision phenomena between core rocket and booster. And a slight variation of motion is observed from the comparison between inviscid and turbulent analyses. Change of separation trajectory based on viscous effects is just a few percent and therefore, inviscid analysis is sufficient for the simulation of separation motion if the study is focused only on the movement of strap-ons.

• Korean Journal of Materials Research
• /
• v.26 no.11
• /
• pp.611-622
• /
• 2016

Particle morphology change and different experimental condition analysis during composite fabrication process by traditional ball milling with discrete element method (DEM) simulation were investigated. A simulation of the three dimensional motion of balls in a traditional ball mill for research on the grinding mechanism was carried out by DEM simulation. We studied the motion of the balls, the ball behavior energy and velocity; the forces acting on the balls were calculated using traditional ball milling as simulated by DEM. The effect of the operational variables such as the rotational speed, ball material and size on the flow velocity, collision force and total impact energy were analyzed. The results showed that increased rotation speed with interaction impact energy between balls and balls, balls and pots and walls and balls. The rotation speed increases with an increase of the impact energy. Experiments were conducted to quantify the grinding performance under the same conditions. Furthermore, the results showed that ball motion affects the particle morphology, which changed from irregular type to plate type with increasing rotation speed. The evolution was also found to depend on the impact energy increase of the grinding media. These findings are useful to understand and optimize the particle motion and grinding behavior of traditional ball mills.