• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1999년도 제17회 학술발표회 논문개요집
• /
• pp.109-109
• /
• 1999

Recently, low energy ion beam irradiation has been adopted for surface modification. Low energy ion beam irradiation has many advantages in polymer engineering such as weak damage, good adhesion, noticeably-enhanced wettability(less than 15 degree), good reproducibility and so on. In this experiment, chemical reactions between free radicals and environment gas species have been investigated using angle-resolved XPS and TRIM code. In the case of low ion beam energy (around 1 keV), energy loss in polymer is mainly originated from atomic collisions instead of electronic interference. Atomic collisions could generated displaced atoms and free radicals. Cold cathode-ion source equipped with 5cm convex grid was used in an O2 environment. Base and working pressure were 5$\times$10-6 and 2.3$\times$10-4 Torr. Flow rates of argon and oxygen were fixed at 1.2 and 8 sccm. target materials are polyethylene polyvinyidenefluoride and polytetrafluoroethylene.

• Journal of Power Electronics
• /
• 제6권2호
• /
• pp.104-113
• /
• 2006

Satellites have provided the impetus for the orderly development of reliability engineering research and analysis because they tend to have complex systems and hence acute problems. They were instrumental in developing mathematical models for reliability, as well as design techniques to permit quantitative specification, prediction and measurement of reliability. Reliability engineering is based on implementing measures which insure an item will perform its mission successfully. The discipline of reliability engineering consists of two fundamental aspects; $(1^{st})$ paying attention to details, and $(2^{nd})$ handling uncertainties. This paper uses some of the basic concepts, formulas and examples of reliability theory in application. This paper emphasizes the practical reliability analysis of a Low Earth Orbit (LEO) Micro-satellite power subsystem. Approaches for specifying and allocating the reliability of each element of the power system so as to meet the overall power system reliability requirements, as well as to give detailed modeling and predicting of equipment/system reliability are introduced. The results are handled and analyzed to form the final reliability results for the satellite power system. The results show that the Electric Power Subsystem (EPS) reliability meets the requirements with quad microcontrollers (MC), two boards working as main and cold redundant while each board contains two MCs in a hot redundant.

• 소성∙가공
• /
• 제7권6호
• /
• pp.620-630
• /
• 1998

Conventional hot forging and thixoforging of Al 7075 alloy have been compared with respect to microstructures, formability and hardness. Two distinctive temperature-strain rate ranges for hot forging of Al 7075 alloy were observed from the results of simple compression tests with strain rates of 10-3∼101 sec-1 in the temperatures between $250^{\circ}C$ and $500^{\circ}C.$ In the dynamic recovery range (low temperature-high strain rate range) multi-stage forging was necessary to form a complex shape part due to the lack of formability. In the high temperature-low strain rate range, in which dynamic recrystallization takes place a complex shaped park could be formed by single-stage forging. About 50% cold working in the SIMA process was necessary to get a fine and homogeneous microstructures. Microstructural study suggest that thixoforged Al 7075 part has fine grains and homogeneous microstructures. Its hardness number is almost same to that of conventional hot forged part after aging treatment.

• 대한기계학회논문집
• /
• 제12권5호
• /
• pp.1138-1149
• /
• 1988

본 연구에서는 논란의 여지가 많은 문제점을 구간별 특성 척도 분석으로 보다 명확히 하고, 매질이 물과 공기인 경우 실험을 통하여 난류 열대류 구조를 분석하여 척도분석 및 Kraichnan등의 분석을 통해 확인된 바 있는 지수법칙층의 존재를 확인하 고자 한다.

• 수산해양기술연구
• /
• 제30권1호
• /
• pp.53-63
• /
• 1994

1) 강소성 유한 요소법 프로그램 RDHPSC는 2단헤딩 가공에 있어서의 신뢰 할 수 있는 해석수단이다. 2) RDHPSC에 의한 2단헤딩의 해석은 2단헤딩가공에서의 최적 가공 조건의 결정에 유용한 정보를 제공할 수 있다. 3) 2단헤딩 가공중의 금속흐름을 수치해석에서의 격자 변형에 의해 관찰될 수 있다. 4) 2단헤딩 가공중의 표면 결함의 발생가능성은 수치해석 결과에서 원수방향응력과 계수 D를 관찰함으로서 탐색되어질 수 있다. 5) 2단헤딩가공중에 있어서의 내부결함 발생가능성은 수치해석의 격차 변형을 통하여 알 수 있다. 6) 마무리 가공금형 수명에 대한 최적가공조건은 수치해석에서의 접촉압력을 조사하여 얻을 수 있다.(이 논문의 결론부분임)

• 대한금속재료학회지
• /
• 제50권1호
• /
• pp.13-22
• /
• 2012

Forged and flat-bar rolled STD11 tool steel shows anisotropic dimensional change during heat treatment. The dimensional change in the rolling direction is larger than that in the transverse direction. The cause of the anisotropic dimensional change is that the steel is anisotropic in composition, microstructure and other properties. The decrease of anisotropic distortion in tool steel is important for making better precision cold working dies. In this study, the effect of ingot weight and hot rolling reduction ratio on the anisotropic dimensional change of STD11 during heat treatment has been studied. Dimensional change was evaluated by simulating a real heat treatment process, including gas quenching and tempering. Experimental results showed that all the rolled flat-bar products had anisotropic distortion to some degree, but the anisotropic distortion was reduced as hot rolling ratio increased. Ingot weight had a little effect on anisotropic distortion. Microstructural observation showed that the anisotropic dimensional change of STD11 tool steel was closely related to the amount, shape and distribution of coarse carbides.

• 한국초전도ㆍ저온공학회논문지
• /
• 제22권4호
• /
• pp.40-44
• /
• 2020

This paper describes the real operation of 2 kW class reverse-Brayton refrigeration system with neon as a working fluid. The refrigeration cycle is designed with operating pressure of 0.5 and 1.0 MPa at low and high pressure side, respectively. Compressor package consists of several helium scroll compressors witch are originally used for driving GM cryocooler. Three segments of plate heat exchanger are adopted to cover the wide temperature range and the refrigeration power is produced by turbo expander. The developed refrigeration system is successfully operated at its target temperature of 77 K. In experiments, all parameters such as pressure, temperature, mass flow rate and valve opening are measured to investigate characteristics during cool-down process and normal state. The difference between design and real operation is discussed with measured experimental data. At normal state of 77 K operation, the developed reverse-Brayton refrigeration system shows 1.83 kW at 68.2 K of cold-end temperature.

• 반도체디스플레이기술학회지
• /
• 제20권2호
• /
• pp.43-50
• /
• 2021

The properties of materials which are widely used in industry fields like automobile, shipbuilding, casting, and electronics are strongly needed to have higher surface hardness, lower surface roughness, and higher compressive residual stress. As mentioned above, for the purpose of satisfying three factors, a variety of researches with respect to surface improvement have been actively studied and applied to every industry. SKD61 which is mostly used for die casting process of cold chamber method must meet a countless number of problems which are thermal, mechanical and chemical from highly specific working environment at high temperature over 600℃. Above all, in case of plunger sleeves used for die casting process, thermal fatigue has a bad effect on the surface of an inlet where molten metal is repeatedly injected. On account of it, plunger sleeves cause manufacturers to deteriorate quality of products. Therefore, in this paper, to improve the surface of an inlet of plunger sleeve, multilayer PVD coating using Ti, Cr and Mo is suggested. Furthermore, The surface characteristics such as surface roughness(Rsa, Rsq), surface hardness(HRB, HRC) and residual stress using XRD(X-ray diffractometer) of coated samples and specimens are studied and discussed.

• 대한한의학원전학회지
• /
• 제35권2호
• /
• pp.121-141
• /
• 2022

Objectives : This paper aims to examine the Yin-Yang characteristics of bland taste. Methods : Medicinals including bland taste were searched in herbology textbooks and mainly in the Bencaogangmu, of which major discourses were analyzed to examine the Yin-Yang characteristics of bland taste. Results & Conclusions : Most medicinals with bland taste were sweet-bland-cold, holding properties of cooling heat, stimulating urination and detoxification. These properties could be explained in relation to the Triple Burner's metabolism of Qi and fluids, as they stimulate perspiration and urination, improving the flow of fluids which in turn supports production of Original Qi, by working on the TB's Qi circulation system. In the bland taste discourse, it was understood that bland taste moves the Qi system and produces fluids, by first ascending then descending. Zhudanxi and the Neijing have opposing views on whether bland taste is Yin or Yang, but both saw blandness to have both Yin and Yang qualities. Characteristics of the bland taste could be better understood in relation to the Triple Burner. The phrase 'bland is attached to sweet taste[淡附于甘]' refers to the likeliness between the two tastes in that bland taste has the Central Earth qualities, integrating others and concealing itself in its blandness, its taste unspecific, mild and unstimulating thus communicating the Qi within the entire Triple Burner from Upper to Middle to Lower, as does sweet taste.

• 한국광학회지
• /
• 제29권3호
• /
• pp.110-118
• /
• 2018

항공용 전자 광학 타겟팅 시스템을 위한 중적외선 광학계를 설계하였다. 본 광학계는 이중 시야를 갖도록 설계되었으며, 빔 축소 전단 광학계, 줌 렌즈 그룹, 릴레이 렌즈 그룹, 콜드스탑 공액 광학계 및 냉각 적외선 검출기로 구성된다. 적외선 검출기는 단일 화소의 크기가 $15{\times}15{\mu}m$ 인 $1280{\times}1024$ 화소 배열을 가지며 잡음을 최소화하기 위하여, f/5.3의 냉각 콜드스탑이 적용된 제품으로 선정하였다. 이중 시야 ($1.50^{\circ}{\times}1.20^{\circ}$, $5.40^{\circ}{\times}4.23^{\circ}$)는 두 개의 렌즈를 삽입하는 방식으로 구현했으며, 줌 배율 변경 시 모든 시야에 걸쳐 f/5.3의 콜드스탑의 효율을 유지하도록 설계하였다. 열 효과가 이미지에 미치는 영향을 조사하기 위해 비열화 및 나르시서스 분석을 수행하였으며, 비열화 분석은 $-55{\sim}50^{\circ}C$의 작동 온도를 기준으로 초점 이동과 잔여 고차 파면 수차에 조사하였고 제르니케 다항식을 이용한 민감도 분석을 수행하여 최적의 보상자를 선정하였다. 선정된 보상자의 최적 이동을 고려한 MTF 해상력을 확인한 결과, 작동 온도 전 구간에 걸쳐 요구조건인 33 lp/mm에서 축상 10% 이상의 성능을 유지하는 것을 확인하였으며, 나르시서스 분석 결과, NITD (Narcissus Induced Temperature Difference) 값이 $1.5^{\circ}C$ 이하가 되도록 설계 된 것을 확인하였다.