• Journal of Powder Materials
• /
• v.18 no.6
• /
• pp.552-561
• /
• 2011

This study attempted to manufacture a Cu-15 at.%Ga coating layer via the cold spray process and investigated the effect of heat treatment environment on the properties of cold sprayed coating material. Three kinds of heat treatment environments, $5%H_2$+argon, pure argon, and vacuum were used in this study. Annealing treatments were conducted at $200{\sim}800^{\circ}C$/1 hr. With the cold sprayed coating layer, pure ${\alpha}$-Cu and small amounts of $Ga_2O_3$ were detected in the XRD, EDS, EPMA analyses. Porosity significantly decreased and hardness also decreased with increasing annealing temperature. The inhomogeneous dendritic microstructure of cold sprayed coating material changed to the homogeneous and dense one (microstructural evolution) with annealing heat treatment. Oxides near the interface of particles could be reduced by heat treatment especially in vacuum and argon environments. Vacuum environment during heat treatment was suggested to be most effective one to improve the densification and purification properties of cold sprayed Cu-15 at.%Ga coating material.

• Journal of Powder Materials
• /
• v.3 no.4
• /
• pp.227-232
• /
• 1996

(i) The development of a metallurgical bond during the spray forming of clad products has offered the possibility of manufacturing large rolls, including those used in hot and cold strip mills. Small rolls are already being produced in Japan. (ii) Technical developments, including the use-of-multi-atomizers have resulted in the elimination of porosity from the internal bore of a sprayed tube. Bimetallic tubing can also be manufactured and the installation of a 4.5 ton tube plant in the USA should provide low operation costs. (iii) Spray forming offers a potentially low cost manufacturing route for superalloy ring/casing components in high strength superalloys. (iv) A large pilot plant has been built for the spray forming of ultra-clean superalloys for turbine disc applications. (v) Using twin-atomizing technology, special steel billets have been spray formed up to 400mm diameter with deposition yields in excess of 90%. (vi) Al/Si alloy extrusion billets with excellent dimensional tolerances are being manufactured for large scale automotive applications. Several new aluminum alloys have also been developed, including high strength, low density and low cocfficient of expansion materials. (vii) New copper alloys have been developed and pilot plants are in operation to produce these alloys once markets have become established.

• Journal of the Korean institute of surface engineering
• /
• v.45 no.3
• /
• pp.111-116
• /
• 2012

Oblique angle deposition (OAD) is a physical vapor deposition method which utilizes non-normal angles between the substrate and the vaporizing source. It has been known that tilting the substrate changes the properties of the film deposited on it, which was thought to be a result of morphological change of the film. In this study, OAD has been applied to prepare single and multilayer Al films by magnetron sputtering. The magnetron sputtering source of 4 inch diameter was used to deposit the films. Al films have been deposited on Si wafers and cold-rolled steel sheets. The multilayer films were prepared by changing the tilting angle upside down at each layer interval, which means that when the first layer was deposited at an angle of $+45^{\circ}$, the second layer was deposited at an angle of $-45^{\circ}$, and vice versa. The microstructure, surface roughness and reflectance of the films were investigated using a scanning electron microscope, a surface profiler and a spectrophotometer, respectively. The corrosion resistance was measured and compared using the salt spray test. The single layer film prepared at an oblique angle of $60^{\circ}$ prepared at other angles. However, for the multilayer films, the film prepared at an oblique angle of $45^{\circ}$ showed the most compact and featureless structure. The multilayer films were found to exhibit higher corrosion resistance than the single layer films.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.123-123
• /
• 2011

알루미늄은 경량 금속으로 부식 저항력이 높아 철을 부식으로부터 보호하기 위한 표면처리 소재로 사용되고 있다. 철의 부식을 방지하기 위해서 알루미늄을 코팅하는 경우, 코팅 방법은 용융도금법이 주로 사용되고 있으며, 알루미늄을 빛의 반사막으로 활용하는 경우 진공 중에서 물리기상증착(physical vapor deposition; PVD)법을 사용하기도 한다. 알루미늄 박막을 물리기상 증착으로 코팅하면 박막성장 초기에 핵(nucleus)을 형성하고, 형성된 핵을 중심으로 주상정(column)으로 박막이 성장하는 것이 일반적이다. 알루미늄 박막의 주상정과 주상정 사이에 공극(pore)이 존재하기 때문에 알루미늄 박막을 부식방지 막으로 이용하기 위해서는 두께를 증가시켜야 한다. 본 연구에서는 스퍼터링(unbalanced magnetron sputtering)을 이용하여 치밀한 조직을 갖는 알루미늄 박막을 코팅할 수 있는 공정변수를 도출하고, 치밀한 알루미늄 조직이 철의 부식에 미치는 영향을 평가하였다. 기판은 냉연강판(cold rolled steel sheet)이 사용되었으며, 알루미늄 타겟의 크기는 직경 4 inch이었다. 알루미늄 박막의 미세조직과 밀도에 영향을 주는 공정변수를 확인하기 위해서 스퍼터링 파워, 공정 압력, 외부 자기장 세기 등의 조건을 변화시켜 코팅을 실시하였다. 알루미늄 박막의 밀도 변화에 가장 큰 영향을 준 공정변수는 외부 자기장의 세기와 방향이었다. 알루미늄 박막이 약 3 ${\mu}m$의 두께로 코팅된 냉연강판을 염수분무시험(salt spray test, 5% NaCl)으로 부식특성을 평가한 결과, 시험을 시작한 후 120시간 후에도 적청이 발생하지 않았다. 이러한 결과는 기존의 동일한 두께를 갖는 알루미늄이 코팅된 강판의 내부식 특성의 2배의 성능을 보여준다.

• Journal of the Korean institute of surface engineering
• /
• v.49 no.5
• /
• pp.454-460
• /
• 2016

Double-layered Al-Mg films have been deposited by using an e-beam deposition method on a cold-rolled steel sheet(CR), which the structure of the film was Al/Mg/CR. The micro-structure, alloy phase, and corrosion resistance of the Al-Mg coated CR were investigated before and after heat treatment at $400^{\circ}C$ for 2, 3, and 10 min in a nitrogen atmosphere. Total thickness of Al-Mg films was fixed at $3{\mu}m$ and the thickness ratio of Al and Mg layers(Al:Mg) has been changed from 5:1 to 1:5. The cross-sectional morphology of the films, which had the thickness ratio of 2:1(Al:Mg), 1:1, and 1:2, was changed after heat treatment from columnar to featureless structure. The x-ray diffraction data for as-deposited films showed only pure Al and Mg peaks. Al-Mg alloy peaks such as $Al_3Mg_2$ and $Al_{12}Mg_{17}$ phase appeared after the heat treatment. The Al-Mg coating with the thickness ratio of 1:1(Al:Mg) showed the best corrosion resistance of up to 500 hours by salt spray test.

• Journal of the Korean institute of surface engineering
• /
• v.49 no.2
• /
• pp.202-210
• /
• 2016

This study was intended to investigate the effect of the amount of magnesium addition and heat treatment in the Al-Mg coating film in order to improve corrosion resistance of aluminum coating. Al-Mg alloy films were deposited on cold rolled steel by physical vapor deposition sputtering method. Heat treatment was fulfilled in an nitrogen atmosphere at the temperature of $400^{\circ}C$ for 10 min. The morphology was observed by SEM, component and phase of the deposited films were investigated by using GDLS and XRD, respectively. The corrosion behaviors of Al-Mg films were estimated by exposing salt spray test at 5 wt.% NaCl solution and measuring polarization curves in deaerated 3 wt.% NaCl solution. With the increase of magnesium content, the morphology of the deposited Al-Mg films changed from columnar to featureless structure and particle size was became fine. The x-ray diffraction data for deposited Al-Mg films showed only pure Al peaks. However, Al-Mg alloy peaks such as $Al_3Mg_2$ and $Al_{12}Mg_{17}$ were formed after heat treatment. All the sputtered Al-Mg films obviously showed good corrosion resistance compared with aluminum and zinc films. And corrosion resistance of Al-Mg film was increased after heat treatment.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.45-45
• /
• 2011

알루미늄과 그 합금은 내부식성(corrosion resistance)이 좋고, 밀도가 낮아 높은 연료소비 효율을 필요로 하는 항공기와 자동차 같은 운송수단의 내-외장 소재로 사용되고 있다. 또한 알루미늄의 높은 내부식성을 이용하여 철강소재의 부식을 방지하는 보호막으로도 폭 넓게 사용된다. 물리기상증착(physical vapor deposition)으로 알루미늄을 코팅하면 박막 성장 초기단계에서 핵(nucleus)을 형성하고, 형성된 핵을 중심으로 주상 구조(columnar structure)로 박막이 성장하는 것이 일반적으로 알려진 방식이다. 주상 구조의 알루미늄 박막은 주상정과 주상정 사이에 필연적으로 공극(pore)이 존재하게 되어 부식을 일으키는 물질이 박막으로 침투하게 되고, 부식 물질과 모재가 반응하여 공식(pitting corrosion)이 발생한다. 본 연구에서는 스퍼터링(magnetron sputtering)을 이용하여 치밀한 조직을 갖는 알루미늄 박막을 코팅할 수 있는 공정을 개발하고, 치밀한 알루미늄 조직이 내부식성에 어떠한 영향을 미치는지 평가하였다. 기판은 냉연강판(cold rolled steel sheet)이 사용되었으며, 알루미늄 타겟의 순도는 99.999%, 크기는 직경 4"이었다. 냉연강판은 진공용기(vacuum chamber)에 장착하기 전에 계면활성제를 이용하여 표면에 존재하는 기름성분을 제거하였으며, 진공용기에 장착한 후에는 아르곤 가스를 이용하여 발생시킨 글로우 방전으로 표면에 존재하는 산화물을 제거하였다. 알루미늄 박막의 조직에 영향을 미치는 공정변수를 확인하기 위해서 스퍼터링 파워, 공정 온도, 공정 압력, 외부 자기장 세기 등의 공정 조건을 변화시켜 코팅을 실시하였다. 실험을 통해서 얻어진 최적 조건으로 알루미늄을 코팅할 경우, 알루미늄 bulk의 밀도와 비교하여 약 94.7%의 밀도를 갖는 알루미늄 박막을 코팅할 수 있었다. 알루미늄 박막이 약 3 ${\mu}$m의 두께로 코팅된 냉연강판의 내부식성 평가(salt spray test, 5% NaCl) 결과, 평가를 시작한 후 72시간 후에도 적청이 발생하지 않았다.