• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.6
• /
• pp.603-611
• /
• 2008

In this paper, we introduce a multi-coil antenna which is useful for reducing the effects of radio frequency noise in an inductively coupled RFID system. A multi-coil antenna is composed of a central coil and four subsidiary coils that are connected in series. A multi-coil antenna is designed so that the total noise disappear when the induced voltages of a central coil and subsidiary coils are added. The noise in a multi-coil antenna was about 30 dB lower than that in a single coil antenna. The multi-coil antenna is very effective in noise reduction even in an environment that the spatial distribution of RF noise is changed abruptly, and the induced noise was about 16 dB lower than that in a dual coil antenna.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.6 s.121
• /
• pp.648-655
• /
• 2007

In this paper, we introduce a dual coil antenna which is useful for reducing the effects of radio frequency noise in an RFID system. A dual coil antenna is composed of two identical coils that are connected in series. The noise voltages in the two coils almost disappear when they are added because the magnitudes are equal and the polarities are opposite. The noise in an RFID reader with a dual coil antenna was 15 dB lower than that with a single coil antenna.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2001.11a
• /
• pp.106-110
• /
• 2001

In this paper, a broadband sleeve monopole antenna using a loading coil in sleeve is proposed. The antenna of the proposed structure has the same of the single sleeve monopole antenna, except for using the coil instead of the inner conductor in sleeve. As a result, it is found that the bandwidth is 1.239～2.154 GHz(above 53.9%) for S$\sub$11/=-10dB(VSWR<2), and the antenna impedance is good for a communication system and feeder which the impedance has 50$\Omega$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.3
• /
• pp.250-256
• /
• 2002

In this paper, a broadband sleeve monopole antenna using a loading coil in sleeve is proposed. The center frequency of the proposed antenna is 1,990MHz. The antenna of the proposed structure has the same of the single sleeve monopole antenna, except for using the coil instead of the inner conductor in sleeve. As a result, it is found that the bandwidth is 1.239~2.154 GHz(above 53.9 %) for $S_{11}=-10\;d B$(VSWR<2), and the antenna impedance is good for a communication system and feeder which the impedance has 50 Ω.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2005.11a
• /
• pp.117-118
• /
• 2005

• Progress in Superconductivity and Cryogenics
• /
• v.16 no.3
• /
• pp.21-25
• /
• 2014

As wireless power transfer (WPT) technology using strongly coupled electromagnetic resonators is a recently explored technique to realize the large power delivery and storage without any cable or wire, this technique is required for diffusion of electric vehicles (EVs) since it makes possible a convenient charging system. Typically, since the normal conducting coils are used as a transmitting coil in the CPT system, there is limited to deliver the large power promptly in the contactless EV charging system. From this reason, we proposed the combination CPT technology with HTS transmitting antenna, it is called as, superconducting contactless power transfer for EV (SUWPT4EV) system. As the HTS coil has an enough current density, it can deliver a mass amount of electric energy in spite of a small scale antenna. The SUCPT4EV system has been expected as a noble option to improve the transfer efficiency of large electric power. Such a system consists of two resonator coils; HTS transmitting antenna (Tx) coil and normal conducting receiver (Rx) coil. Especially, the impedance matching for each resonator is a sensitive and plays an important role to improve transfer efficiency as well as delivery distance. In this study, we examined the improvement of transmission efficiency and properties for HTS and copper antennas, respectively, within 45 cm distance. Thus, we obtained improved transfer efficiency with HTS antenna over 15% compared with copper antenna. In addition, we achieved effective impedance matching conditions between HTS antenna and copper receiver at radio frequency (RF) power of 370 kHz.

• Journal of electromagnetic engineering and science
• /
• v.13 no.1
• /
• pp.51-53
• /
• 2013

A MIMO antenna using the resonance of ground planes is proposed for 4G mobile application. A resonant mode is generated when the double ground planes (upper and lower) in the mobile terminal are excited as the radiator. By combining the resonant modes contributed from both the antenna element and the ground planes, the proposed MIMO antenna realizes a wideband property over LTE band 13. In addition, an inductive coil is employed to reduce the antenna volume. These approaches not only simplify antenna design but also effectively improve bandwidth and efficiency. The proposed MIMO antenna has an excellent ECC value of below 0.1 because of the nearly orthogonal radiation patterns of the two radiators. Moreover, an additional antenna is adopted to cover WiMAX, WLAN, and Bluetooth services simultaneously in frequency range from 2 GHz to 2.7 GHz.

• Journal of Korea Multimedia Society
• /
• v.18 no.4
• /
• pp.541-545
• /
• 2015

Wireless power transmission which can transmit the electrical power through the air is the promise technology. In this paper, the effects of wireless power transmission using magnetic resonance method have been studied on coil material, resonance frequency, and antenna type. We have found copper tube as a coil material had the better characteristics than that of enameled wire, and the optimal resonance frequency was 13.6MHz in the range of from 1MHz to 20MHz. And the double square spiral type antenna as a load coil was the best. The power transmission distance by magnetic resonance method with 13.6MHz was 150 cm.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2001.11a
• /
• pp.315-318
• /
• 2001

We are proposing a new mobile phone antenna, which has a specially manufactured Mn-Zn cylindrical ferrite bead inside of the helical coil of the antenna. The extended antenna radiation patters and the spatial peak SAR averaged over 1 gram simulated tissue with and without the ferrite bead insertion were measured at 824 MHz. The results show that the ferrite bead resulted in SAR reduction about 20 %, and reflection coefficient increase about 7 % for the extended antenna. The applicability of this scheme to the antenna mass production is quite feasible.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.8
• /
• pp.73-80
• /
• 2020

The 3D printing of electronics has been a major application topics in additive manufacturing technology for a decade. In this paper, wireless power transfer (WPT) technology for 3D electronics is studied to supply electric power to its inner circuit. The principle of WPT is that electric power is induced at the recipient antenna coil under an alternating magnetic field. Importantly, the efficiency of WPT does rely on the design of the antenna coil shape. In 3D printed electronics, a flat antenna that can be placed on the printed plane within a layer of a 3D printed part is used, but provided a different antenna response compared to that of a conventional PCB antenna for NFC. This paper investigates the WPT response characteristics of a WPT antenna for 3D printed electronics associated with changes in its design elements. The effects of changing the antenna curvature and the gap between the wires were analyzed through experimental tests.