• Journal of the Korean institute of surface engineering
• /
• v.5 no.3
• /
• pp.77-85
• /
• 1972

A method of preparation of synthetic ignorgaic coating on copper (patina) has been presented . An Eh--pH diagram was constructed for the present Cu-H2O-SO$_4$ system using the most recently available thermodynamic data. In the path of the patination at room temperature the general behaviour of copper in acidic copper sulfate solutions with potassium chlorate as an oxidizing agent appeared to follow those predictable in this Eh-pH diagram. In the presence 0.05 molar cupric sulfate at a temperature of about 28$^{\circ}C$ a green brochantite (CuSO$_4$$.$3Cu(OH)$_2$) layer was formed on copper sheet in 20 days. In a solution having an initial pH of 3.5 the development of a brochantite coating has been observed to take place in two stages. In the first, a layer of cuprous oxide formed on the copper at a relatively rapid rate. In the ensuing step the outer layer of cuptrite was oxidized at much slower rate to form brochantite. The syntetic coatings appeared to consist of crystal-lites of brochanitite growing perpendicular to the cuprose oxide surface. The outer tips of the -crystallites were reasily broken off and gave to the layer a rather chalky character. Underneath, at the brochantite Cu$_2$O interface, however, the green layers were firmely attached. The effect of reagent concentration , solution agitation , and moderate temperature increase were investigated to improve the quality of coating. So also in a qualitative way were the effect of light.

• Corrosion Science and Technology
• /
• v.18 no.1
• /
• pp.16-23
• /
• 2019

Steels for automotive fuel tank require unique properties such as corrosion resistance for fuel, welding for joining, forming for press, and painting for exterior. Recently, automakers have been requiring excellent seam weldable steels to enhance manufacturing productivity of fuel tank. Thus, POSCO developed a new type of functional steels coated with nano-composite thin layer on Zn-Ni plating steels. The nano-composite coating solution was prepared by mechanical fine dispersion of solutions consisting of polymeric resin and nano-composite materials in aqueous media. The composite solution was coated on the plating steel surface by using roll coater and cured through induction furnace. These new developed plating steels were evaluated for quality performances such as seam and spot weldability, press formability, and corrosion resistance. These new functional steels coated with nano-composite layer exhibited excellent seam weldability and press formability. Detailed discussion of coating solution and experimental results suggest that nano-sized composite dispersion as coating layer plays a key role in enhancing the quality performance.

• Journal of Electrochemical Science and Technology
• /
• v.10 no.2
• /
• pp.148-158
• /
• 2019

The corrosion protection of AA2024 PPy coated samples doping with nanosized metal oxides, including $TiO_2$ and $CeO_2$ nanoparticles and $Nd_2O_3$ nanorods, during exposure to the solutions of 0.1 M $H_2SO_4$ and 3.5% NaCl was evaluated by electrochemical impedance spectroscopy (EIS) and linear polarization resistance (LPR) techniques. The nanorods of $Nd_2O_3$ were synthesized by cathodic pulse electrochemical deposition technique. The barrier properties of the different PPy coatings containing nanosized metal oxides immersed in $H_2SO_4$ solution were ranked as follows: $Nd_2O_3$ > $TiO_2$ > $CeO_2$. Therefore, the $Nd_2O_3$ coating sample provided the highest corrosion protection at any time of immersion up to 72 hours after immersing in $H_2SO_4$ solution. On the other hand, the $CeO_2$ coating sample displayed the best anticorrosive properties among the other coating samples after immersion in NaCl solution up to 28 days. This is due to the inhibition effect of cerium ions on aluminum alloys at near-neutral solutions.

• Korean Journal of Metals and Materials
• /
• v.48 no.5
• /
• pp.401-409
• /
• 2010

This study was performed to develop an antibacterial film that can be dried at room temperature. A nanosized TiO$_2$ particle-dispersed solution was prepared by the hydrothermal treatment of peroxo-titanic acid at 160${^{\circ}C}$ for 4h. The binder was synthesized through the hydrolysis and condensation reactions of TEOS (10cc) and GPTS (3.5cc) in the mixture of H$_2$O (30cc) and EtOH (30cc). The synthesized binder was mixed with 0.1 M of TiO$_2$ solution in a volume ratio of binder/TiO$_2$ solution=0.25~0.5. The glass substrate was coated after using the dip coating method, which was then followed by drying for over 2h at room temperature. Although the TiO$_2$ particles did not chemically-bond to the binder, the coating layer strongly adhered to the substrate and displayed good antibacterial properties.

• Macromolecular Research
• /
• v.10 no.2
• /
• pp.67-74
• /
• 2002

New immunoprotecting membranes were prepared by spin coating the amphiphilic random multiblock copolymers of poly(ethylene glycol) (PEG) and poly(tetramethylene ether glycol) (PTMEG) or poly(dimethyl siloxane) (PDMS) on porous Durapore(R) membrane. The copolymer coating was intended to make a biocompatible, immunoprotecting diffusional barrier and the supporting porous substrate was for mechanical stability and processability. By filling Durapore(R) membrane pores with water, the penetration of coating solution into the pores was minimized during the spin coating process. A single coating process produced a completely covered thin surface layer (~1 ${\mu}{\textrm}{m}$ in thickness) on the porous substrate membrane. The permselectivity of the coated layer was influenced by PEG block length, polymer composition, and thickness of the coating layer. A composite membrane with the coating layer prepared with PEG 2 K/PTMEG 2 K block copolymer showed that its molecular weight cut-of fat any 40 based on dextran was close to the molecular size of IgG (Mw = 150 kDa). However, IgG permeation was detected from protein permeation test, while glucose oxidase (Mw = 186 kDa) was not permeable through the coated membrane.

• Corrosion Science and Technology
• /
• v.15 no.2
• /
• pp.78-83
• /
• 2016

The e-coating to inhibit induced corrosion can deposit a coating not only on the exterior surface but also on the inside of whole metallic components of body-in-white (BIW). But it is difficult to deposit paint films on the inside area because metallic components are multi layered. It may cause shortness of e-coating thickness. The only way to properly verify e-coating thickness is by performing the use of tear-down prototypes. When paint films' thickness is inadequate, a structural modification on each metallic component is needed. Verification of the thickness improvement for a structural modification requires much manual effort and leads to increasing development time. Recently, the simulation technology has been developed to predict the e-coating thickness in e-coating field. By applying the simulation to BIW, improvement in paint thickness quality and shortening of development period are expected. The paper explains a validated solution that allows simulating the effect of design changes to the e-coating thickness and current density, thereby delivering results within a time frame of a few days.

• Journal of Applied Biological Chemistry
• /
• v.58 no.1
• /
• pp.61-64
• /
• 2015

As an edible coating, carnauba shellac wax (CSW) and lemongrass oil (LO) solution was prepared to extend the shelf life of 'Hongro' apples. During storage, there were significant differences in the populations of total aerobic bacteria, yeast, and molds between the coated apples and the control samples. The weight loss and vitamin C loss of apples coated with the CSW-LO solution were lower than those of the control. These results suggest that CSW-LO coating can be an effective method for improving quality of 'Hongro' apples.

• Journal of Pharmaceutical Investigation
• /
• v.41 no.4
• /
• pp.211-215
• /
• 2011

The aim of this study was to develop a stable enteric coated diclofenac sodium (DFS) tablets using Aqua-Polish E without using a subcoat. DFS uncoated tablets were manufactured through the non direct compression process. AquaPolish E white aqueous coating dispersion was used as enteric coating material. This film forming polymer is a mixture of selected polymethacrylic/ethylacrylate copolymers. The stability of the obtained enteric coated tablets was evaluated according to ICH guidelines. No signs of disintegration or cracking was observed when they placed in 0.1N HCl solution (pH1.2), but they were completely disintegrated within 10 minutes when they placed in buffered solution at pH6.8. Dissolution test was also conducted by placing tablets in 0.1 N HCl for 2 hours and then 1 hour in phosphate buffer at pH 6.8. Less than 0.9 % of drug was released in the acidic phase and up to 97% in the basic medium. These findings suggest that aqueous enteric coating with AquaPolish E system is an easy and economical approach for preparing stable DFS enteric coat without the use of a subcoating layer.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.135-135
• /
• 2003

This paper presents the preparation of SnO$_2$ films by Sol-Gel process and using spin coating method, and their sensing properties in CO gas. Experimental procedure consisted of following steps: (1) Tin chloride(SnCl$_4$) and Ammonium hydrogen carbonate (NH$_4$HCO$_3$) were used as precursors; (2) the Sol solution with concentration of about 10wt% SnO$_2$ was prepared from washed Gel-precipitate for spin coating step; (3) thereafter, the coating solution was dropped onto the alumina (Al$_2$O$_3$) substrate that was then spun, the spin coating was carried out with total 10 times; (4) finally, the films were calcined for 3 hours at 50$0^{\circ}C$ or higher temperature (600, 700, 800 or 90$0^{\circ}C$) in order to obtain various gram sizes. The average grain size was calculated by Scherrer's equation using main peaks in XRD spectra; meanwhile the thickness, microstructure and surface morphology of the films were observed by FE-SEM.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.9
• /
• pp.429-433
• /
• 2006

PZT(80/0) powder was prepared by a sol-gel method and PZT thick films were fabricated by the screen-printing method on the alumina substrates. The coating and drying procedure was repeated 4 times. And then the PZT(20/80) precusor solution was spin-coated on the PZT thick films. A concentration of a coating solution was 0.5mol/L and the number of coating was varied from 0 to 6. The porosity decreased and the grain size increased with increasing the number of coatings. The thickness of the PZT-6(6: number of coatings) films was about $60{\mu}m$. The relative dielectric constant increased and the dielectric loss decreased with increasing the number of PZT(20/80) sol coatings. The relative dielectric constant and dielectric loss of the PZT-6 thick film were 275 and 3.5%, respectively. The remanent polarization, coercive field and breakdown strength of the PZT-6 film were $19.8{\mu}C/cm^2$, 13.7kV/cm and 130kV/cm, respectively.