• Advances in materials Research
• /
• 제6권4호
• /
• pp.343-348
• /
• 2017

High-pressure gas atomization was employed to prepare the Fe-based $Fe_{50}Cr_{24}Mo_{21}Si_2B_3$ alloy powder. The effect of flow rate of atomizing gas on the median powder diameter was studied. The results show that the powder size decreased with increasing the flow rate of atomizing gas. Fe-based alloy coatings with amorphous phase fraction was then prepared by high velocity oxygen fuel spraying (HVOF) of gas atomized $Fe_{50}Cr_{24}Mo_{21}Si_2B_3$ powder. Microstructural studies show that the coatings present dense layered structure and low porosity of 0.17% in about $200{\mu}m$ thickness. The Fe-based alloy coating exhibits an average hardness of about 1230 HV. Our results show that the HVOF process results in dense and well-bonded coatings, making it attractive for protective coatings applications.

• 멤브레인
• /
• 제23권4호
• /
• pp.283-289
• /
• 2013

Poly(vinyl alcohol) (PVA)에 대하여 가교제로써 glutaraldehyde (GA), maleic anhydride (MA)를 이용하여 제조한 코팅용액을 알칼리로 가수분해 시킨 poly acrylonitrile (PAN) 중공사 막표면에 코팅하여 막을 제조하였다. 제조된 막의 투과특성평가를 위해서 물/에탄올 혼합액에 대한 투과증발 실험을 수행하였다. $60^{\circ}C$의 90 wt%의 물/에탄올 혼합액에 대하여 반응온도 및 가교제의 농도변화에 따른 투과도 및 선택도를 측정하였다. 일반적으로 반응온도, 가교제 농도가 증가할 경우 투과도는 낮아지고, 선택도는 증가하는 경향을 보여주었다. 가교제로 GA의 대표적 결과는 반응온도 $120^{\circ}C$, GA 11 wt%로 투과도는 $165g/m^2hr$ 선택도는 81이고, MA는 반응온도 $120^{\circ}C$, MA 11 wt%로 투과도는 $174g/m^2hr$ 선택도는 73의 결과를 얻을 수 있었다.

• 한국식품위생안전성학회지
• /
• 제9권3호
• /
• pp.123-131
• /
• 1994

An enzyme-linked immunosorbent assay(ELISA) was developed for the detection of residual gentamicin(GM) in edible animal products. The immunogen(GM-KLH conjugate) and coating antigen(GM-BSA conjugate) were prepared by coupling GM sulfate to keyhole limpet hemocyanin(KLH) and bovine serum albumin(BSA) in the presence of 1-ethyl-3-(3-dimethylaminopropyl)carbodiimide hydrochloride, respectively. Polyclonal antibody to GM was produced in rabbits(New Zealand White, female) by using the immunogen and the antibody titer was measured by indirect ELISA. A competitive ELISA was developed using GM-bovine serum albumin conjugate as a coating antigen, GM(as standards or sample), polyclonal antibody to GM, secondary antibody conjugated with horseradish peroxidase as an enzyme, and H2O2 and o-phenylenediamine dihydrochloride as a substrate and a chromophore, respectively. The detection limit of GM was 10 ng/ml and the standard curve of GM(n=26) was linear up to 10 $\mu\textrm{g}$/ml in this competitive ELISA system. There were no cross-reactivities of the partially purified antibody between GM and the various antibiotice such as amikacin, benzyl-penicillin, chloramphenicol, erythromycin, furazlidone, kanamycin, neomycin, oleandomycin, streptomycin, sulfathiazole and thiamphenicol(CR50<0.05%)

• 대한화학회지
• /
• 제45권2호
• /
• pp.156-161
• /
• 2001

여러 가지 산화상태의 폴리아닐린을 화학적으로 합성하여 FT-IR, UV-Vis, GPC, TG-DTA로 측성 분석하였다. ITO 기관위에 다양한 산화상태의 LEB-PAN/NMP 용액으로 스핀코팅하고, AI 전극을 진공증착하여 단일층 발광다이오드를 제작하고 I-V 특성과 EL 스팩트럼에서 완전환원형인 LEB 함량이 증가할수록 ${\pi}$-${\pi}$* 전이의 장파장이동과 분자 엑시톤 전이 세기가 감소하고 PL과 EL 세기가 증가하는 것을 확인하였다. ITO/LEB/AI 구조의 LED에서 작동 전압은 5V 이었다. 백색광은 단지 폴리아닐린의 환원형 구조에서만 발광하는 것을 확인하였다.

• Applied Microscopy
• /
• 제10권1_2호
• /
• pp.7-17
• /
• 1980

Electron microscope radioautography introduced by Liquier-Milward (1956) is now used routinely in many laboratories. Most of the technical difficulties in specimen preparation have been overcome. This method is modified from loop method for improvement of EM radioautographic techniques. The advantages of this method are: 1. the use of single specimens on small corks and of a large wire loop, allows the experimenter to avoid the blemishes in the membrane; 2. the surfactant dioctyl sodium sulphosuccinate is added to diluted ILford L4, thus greatly prolonging the period of time over which good emulsion layers can be made; 3. corks can be handled in perspex holder which allows about 20 specimens to be developed simultaneously. The steps of the method comprise: 1. Cut ribbons of ultrathin sections of silver interference colour 2. Pick them up on formvar-coated 200 mesh grids 3. Prestaining of tissues 4. Coat the specimens with a thin layer of carbon by evaporation (30-60A) 5. Mount the specimens on corks (about 1cm apical diameter) using double-sided scotch tape 6. Emulsion coating; a. Take a 250m1 beaker, place it on the pan of a sliding weight balance and weigh it. Add 10 grams extra to the beam. Add pieces of ILford L4 emulsion to the beaker until the balance is swinging freely. Add the 20ml of distilled water that was previously measured out. b. Surfactant dioctyl sodium sulphosuccinate is added to diluted ILford L4. 7. Prepare a series of membranes of gelled emulsion with the wire loop and apply one to each cork-borne specimen. 8. Put the specimens away to expose by pushing the corks into short length of PVC tubing, each tube having a small hole in the side 9. Place the tubes in small boxes together with silica gel. 10. Exposure 11. Developer - Kodak Microdol X for 3 minutes 12. Fixer - A perspex holder can be manufactured which allows 20 specimens to be developed simultaneously. 12. Fixer - 30% sodium thiosulfate for 10 minutes 13. Examination with Siemens Elmiskop 1A electron microscope

• Journal of Welding and Joining
• /
• 제31권6호
• /
• pp.96-106
• /
• 2013

In this study, the effect of laser source($CO_2$ and Nd:YAG) on the microstructure and tensile properties of laser welded Al-Si coated boron steel(1.2mmt) was investigated with before and after hot-stamping. In case of as welds condition, fracture occurred in base metal unrelated to the laser source. It could be explained that tensile strength of fusion zone composed of martensite and bainite is higher than that of base metal that contains a lot of ferrite despite dilution of Al and Si from coating layer to fusion zone. In case of hot-stamping condition, the fracture occurred in fusion zone irrelevant to laser source and the tensile strength was lower than hot stamped base metal. In the $CO_2$ laser welds, $Fe_3$(Al,Si) formed near the bond line was transformed into ferrite during hot-stamping. Therefore tensile strength of bond line is lower than that of base metal and center of fusion zone and the fracture occurred in the bond line. On the other hand, in the Nd:YAG laser welds, the higher concentration of Al formed the ferrite in the fusion zone during hot-stamping treatment. Also, the thickness of centerline was thinner than that of base metal. Therefore, it is considered that fracture occurred in centerline of fusion zone due to effect of concentration stress, and it leaded to a lower tensile strength and elongation.

• Corrosion Science and Technology
• /
• 제12권1호
• /
• pp.1-6
• /
• 2013

Recently Digital TV industry has drastically been moving the illuminating system, which causes an obvious product change from PDP and LCD to LED model to provide high-definition image. Due to strong competition in the digital industry, TV manufacturers make a great efforts to reduce production cost by using low-priced materials such as steels instead of aluminum and plastic etc. In this paper we have developed a new low-priced electrogalvanized steel sheet, which has a black resin composite layer, to substitute conventional high-priced PCM steel and plastic mold for rear cover panel in the digital TV. The black resin composite was prepared by mechanical dispersion of the mixture solution that consists of high solid polyester resin, melamine hardener, black pigment, micronized silica paste, polyacrylate texturing particle and miscellaneous additives. The composite solution was coated on the steel sheet using roll coater followed by induction furnace curing and cooling. Although the coated layer has a half thickness compared to the conventional PCM steels having $23{\mu}m$ thickness, it exhibits excellent quality for the usage of rear cover panel. The new steel sheet was applied to test products to get quality certification from worldwide electronic appliance customers. Detailed discussion provides in this paper including preparation of composite solution, roll coating technology, induction curing technology and quality evaluation from customers.

• 한국토양비료학회지
• /
• 제15권3호
• /
• pp.188-193
• /
• 1982

분말황산가리(粉末黃酸加里)와 입도(粒度)를 달리한 수종의 광물분말(제오라이트, 활석(滑石), 사문석(蛇紋石))을 혼합(混合) 또는 피복(被覆) 조입(造粒)하여 그 조입율(造粒率)과 물리적(物理的)인 특징(特徵)을 조사(調査)한 결과(結果) 3종(種) 광물 공(共)히 조입율(造粒率)을 향상(向上)시켰으며 활석(滑石), 제오라이트 사문석(蛇紋石) 순(順)으로 조입율(造粒率)이 양호(良好)했고 광물분말 50%까지는 많이 섞을수록 조입율(造粒率)이 증가했다. 조입(造粒)은 물로 가능하며 황산가리(黃酸加里)로만 조입(造粒)할 경우보다 제오라이트와 사문석혼합물(蛇紋石混合物)의 조입(造粒)에는 물이 많이 소요(所要)되나 활석(滑石)의 경우는 감소(減少)했다. 제오라이트는 조입입자(造粒粒子)의 경도(硬度)를 증가시키지만 나머지 광물은 경도(硬度)를 불량(不良)하게 하며 피복조입물(被覆造粒物)은 혼합조입물(混合造粒物)보다 더 쉽게 깨졌다. 낙하파양율(落下破壤率)도 제오라이트가 가장 낮고 혼합비율(混合比率)을 높일수록 더욱 감소(減少)시키며 타광물은 오히려 불량(不良)하게 했다. 피복조립입자(被覆造粒粒子)의 경우는 혼합조입(混合造粒)의 경우와 큰 차이가 없었다. 탈분율도 제오라이트로 혼합(混合), 혹은 피복조입(被覆造粒)할 경우 크게 개선(改善)되었다.

• Journal of Welding and Joining
• /
• 제28권3호
• /
• pp.92-98
• /
• 2010

Ferritic stainless steels, which have relatively small thermal expansion coefficient and excellent corrosion resistance, are increasingly being used in vehicle manufacturing, in order to increase the lifetime of exhaust manifold parts. But, there are limits on use because of the problem related to cosmetic resistance, corrosions of condensation and high temperature salt etc. So, Aluminum-coated stainless steel instead of ferritic stainless steel are utilized in these parts due to the improved properties. In this investigation, Al-8wt% Si alloy coated 409L ferritic stainless steel was used as the base metal during Gas Tungsten Arc(GTA) welding. The effects of coated layer on the microstructure and hardness were investigated. Full penetration was obtained, when the welding current was higher than 90A and the welding speed was lower than 0.52m/min. Grain size was the largest in fusion zone and decreased from near HAZ to base metal. As welding speed increased, grain size of fusion zone decreased, and there was no big change in HAZ. Hardness had a peak value in the fusion zone and decreased from the bond line to the base metal. The highest hardness in the fusion zone resulted from the fine re-precipitation of the coarse TiN and Ti(C, N) existed in the base metal during melting and solidification process and the presence of fine $Al_2O_3$ and $SiO_2$ formed by the migration of the elements, Al and Si, from the melted coating layer into the fusion zone.