• Journal of the Korean institute of surface engineering
• /
• v.29 no.2
• /
• pp.81-92
• /
• 1996

The cementless fixation of bone ingrowth by porous coatings on artificial hip joint prostheses are replacing polymethylmethacrylate(PMMA) bone cement fixations. However, the major interests in the field of porous metal coating are environmental corrosivity accelerated by metal ion release, deterioration in the mechanical property of the coating, and the mechanical failure of the coatings as well as the substrate. Therefore, the selection of right materials for coatings and the development of porous coating techniques must be accomplished. Because of the existing problems in Ti and Ti alloys which are used extensively, this study is focused on the plasma spraying technique for coating on super stainless steel substrate. In order to determine the optimum conditions which satisfy the requirement for the porous coatings, under the plasma spraying, we selected the experimental parameters which extensively influenced on the characteristics of the coating through the pre-examination. Spray distance has been selected among 120, 160, and 200mm and primary gas flow rate among 70, 100, and 130 SCFH. Current and secondary gas($H_2$) flow rate was fixed at 400A, and 15 SCFH respectively. To understand the characteristics of the coatings, surface morphology, cross-sectional micro-structure, surface roughness, residual stress, and corrosion resistance were elucidated and the best conditions for the bone ingrowth improvement on artificial hip joint prostheses were found.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2005.11a
• /
• pp.183-184
• /
• 2005

Four different coatings deposited using cold spray process were studied with two different powder agglomerating techniques (spray d교 and evaporated powder) and using $TiO_2$ nano-sized powders with and without a 10wt% addition of ZnO. Characterization was performed by SEM, XRD and roughness test. Also the photocatalytic effect of the coatings was evaluated. Although the change of powder preparation techniques and the addition of ZnO into $TiO_2$ did not show appreciable variations in the surface morphology and Anatase phase transformation, it did show influence on the surface roughness of the coating, the highest roughness being found in the coatings made by spray powder prepared method. Regarding the photocatalytic effect it was observed that the using the spray dry coating and the addition of ZnO are promoter of purification at higher rates.

• Journal of Mechanical Science and Technology
• /
• v.20 no.10
• /
• pp.1670-1679
• /
• 2006

The development of the oxidation, wear and corrosion resistant materials that could be used in severe environmental conditions is needed. The elementary technologies for surface modification include ion implantation and/or thin film coating. Furthermore, in order to develop ion implantation technique to the specimens with three-dimensional shapes, plasma-based ion implantation (PBII) techniques were investigated. As a result, it was found that the ion implantation and/or thin film coating used in this study were/was effective for improving the properties of materials, which include implantations of various kinds of ions into TiAl alloy, TiN films formed on surface of base material and coatings in high-temperature steam. The techniques proposed in this study provide useful information for all of the material systems required to use at elevated temperature. For the practical applications, several results will be presented along with laboratory test results.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2003.04a
• /
• pp.136.2-136
• /
• 2003

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.4
• /
• pp.16-24
• /
• 2012

To characterize the coating structure, diverse methods such as mercury intrusion, nitrogen adsorption and oil absorption methods have been developed and widely employed. These indirect techniques, however, have some limitation to explain the actual coating structure. Recently microscopic observation methods have been tried for analyzing structural characteristics of coating layers. Preparation of the undamaged cross section of a coating layer is essential for obtaining high quality image for analysis. In this study, distortion-free cross-section of the coating layer was prepared using a grinding and polishing technique. The coated paper was embedded in epoxy resin and cured. After curing the resin block it was ground with abrasive papers and then polished with diamond particle suspension and nylon cloth. Polished coating layer was sufficient enough to obtain undamaged cross sectional images with scanning electron microscope under backscattered electron image mode. In addition, the SEM images allowed distinction of the coating layer components. Also S/B latex film formed between pigment particles was visualized by osmium tetroxide staining. Pore size distribution and pore orientation were evaluated by image analysis from SEM cross-sectional images.

• 한국가스학회:학술대회논문집
• /
• 2001.10a
• /
• pp.58-68
• /
• 2001

Microbiologically influenced corrosion (MIC) of carbon steel gas pipeline in soil environments was investigated at field and laboratory MIC is very severe corrosion and it is not easy to distinguish this corrosion from Inorganic corrosion because of its localized, pitting-type character Therefore, it is important to provide proper assessment techniques for the prediction, detection, monitoring and mitigation of MIC. It is possible to predict the MIC risk, i.e., the activity of sulfate-reducing bacteria (SRB) through the analysis of soil environments. Chemical, microbiological and surface analysis of corrosion products and metal attacked could reveal the possibility of the occurrence of MIC. Various electrochemical and surface analysis techniques could be used for the study of MIC. Among these techniques, thin-film electrical resistance (ER) type sensors are promising to obtain localized corrosion rate of MIC induced by SRB. It is also important to study the effect of cathodic protection (CP) on the MIC In case of coated pipeline, the relationship between coating disbondment and the activity of SRB beneath the disbanded coating is also important.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.25 no.3
• /
• pp.389-396
• /
• 2017

Restorations of automotive parts have been done ever since the first vehicle was produced. Because the most expensive parts of a vehicle are in the engine system, there have been various restoration methods developed for engine parts. In the case of commercial diesel engines, the fuel injection device is a key and expensive component. It also has a significant effect on vehicle performance. In particular, reduced engine power and increased exhaust gas emissions may result from mechanical damage due to abrasion of the spill valve in the fuel injection system of a diesel engine. In this paper, restoration techniques for damaged parts are applied to restore the abrasion of a spill valve of fuel injection, also called as the "unit injector", of commercial diesel engines. In order to recover the damage, optimized polishing techniques using hard-metal and coating processes are applied. To evaluate restoration techniques for the spill valve, performance and durability tests are performed on a test bench.

• Nuclear Engineering and Technology
• /
• v.50 no.2
• /
• pp.229-236
• /
• 2018

Accident-tolerant fuels (ATFs) are currently of high interest to researchers in the nuclear industry and in governmental and international organizations. One widely studied accident-tolerant fuel concept is multilayer cladding (also known as coated cladding). This concept is based on a traditional Zr-based alloy (Zircaloy-4, M5, E110, ZIRLO etc.) serving as a substrate. Different protective materials are applied to the substrate surface by various techniques, thus enhancing the accident tolerance of the fuel. This study focuses on the results of testing of Zircaloy-4 coated with pure chromium metal using the cold spray (CS) technique. In comparison with other deposition methods, e.g., Physical vapor deposition (PVD), laser coating, or Chemical vapor deposition techniques (CVD), the CS technique is more cost efficient due to lower energy consumption and high deposition rates, making it more suitable for industry-scale production. The Cr-coated samples were tested at different conditions ($500^{\circ}C$ steam, $1200^{\circ}C$ steam, and Pressurized water reactor (PWR) pressurization test) and were precharacterized and postcharacterized by various techniques, such as scanning electron microscopy, Energy-dispersive X-ray spectroscopy (EDX), or nanoindentation; results are discussed. Results of the steady-state fuel performance simulations using the Bison code predicted the concept's feasibility. It is concluded that CS Cr coating has high potential benefits but requires further optimization and out-of-pile and in-pile testing.

• The Korean Journal of Community Living Science
• /
• v.24 no.2
• /
• pp.243-249
• /
• 2013

Identification of coating film species from ancient coating materials is needed to maintaine their surfaces without loss of their original beauty for a long time and understand the historical background of manufacturing techniques. A pyrolysis-gas chromatography/mass spectrometry (Py-GC/MS) was applied to identify the origine of films in ancient coating materials. The pyrolysis products, which reflect the source from which they originate were detected distinctively at $500^{\circ}C$. This is a rapid technique that does not require large amounts of sample or any sample preparation. Sesquiterpenes are a class of terpenes that consist of three isoprene units were identified as cadienes, selinenes, cubebenes from the raw material of dendropanax morbifera. On the other hand, alkanes(tetra~heptadecanes), alkenes (tri~heptadecenes), allkyphenols, catechols and fatty acids were detected from the raw material of the lacquer film. Based on these results, the origine of historic coatings artifacts was identified using py-GC/MS by comparison with their pyrolysis products.

• ALGAE
• /
• v.22 no.2
• /
• pp.141-146
• /
• 2007

Seagrass bed is an important component in coastal and estuarine ecosystems, providing food and habitats to a wide variety of marine organisms. Recently, seagrass coverage has declined significantly due to anthropogenic impacts such as cultural eutrophication and reclamation, and thus efforts are under way to prevent further losses and restore disturbed seagrass habitats worldwide. Seagrass transplantation techniques for habitat restoration include vegetative and seed-based methods. Seagrass seeds can be collected easily, and sowing seeds is an economically effective method for large-scale restoration. However, large numbers of seed can be lost by seed predation and physical disturbance in the planting areas. In the present study, Zostera marina seeds were coated with loess to reduce seed loss by predation and sweeping away by the water currents, and germination rates of coated seeds and seedling growth were examined to assess the feasibility of the seed-coating method for large-scale restoration. Germination rate of the coated seeds with loess was significantly higher than that of the uncoated seeds. Additionally, seedling growths were not significantly different between the coated and the uncoated seeds. These results suggest that coating of eelgrass seeds with loess enhances success of seed germintion with no harmful effects on seedling growth. Therefore, the seed coating method using loess may be an effective and applicable seedbased transplanting technique for large-scale restoration.