• 반도체디스플레이기술학회지
• /
• 제18권4호
• /
• pp.69-74
• /
• 2019

The aim of this work is to investigate the effect of the microtip length in a slot-die head on coating of a fine poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS) stripe. To this end, we have employed a meniscus guide with a 150-㎛-wide microtip and performed roll-to-roll slot-die coatings by varying its length between 500 ㎛ and 50 ㎛. When the microtip length is 150 ㎛ or shorter, we have observed three unexpected phenomena; 1) though the solution spreads much wider than the microtip width, yet the coated stripe width is almost the same as the microtip width, 2) the stripe width decreases, but the stripe thickness is rather increased with increasing coating speed at a fixed flow rate, 3) we obtain stripes much narrower than the microtip width at high coating speeds. It is due to the fact that 1) the meniscus is not well controlled by a short microtip, 2) the main stream of solution from the outlet is very close to the substrate and thus the distributed solution along the head lip merges with the main stream, and 3) the solution is not spread over the entire microtip end at high coating speeds, causing a tiny wobble in the meniscus. Using the 150-㎛-wide and 250-㎛-long microtip, we have fabricated 153-㎛-wide and 94-nm-thick PEDOT:PSS stripe at the maximum coating speed of 13 mm/s. To demonstrate its applicability in solution-processable organic light-emitting diodes (OLEDs), we have also fabricated an OLED device with the fine PEDOT:PSS stripe and obtained strong light emission from it.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.59-64
• /
• 2001

The fluid flow, mass transfer and film thickness variation during a wafer spin coating process are numerically studied. Governing equations for the cylindrical coordinates are simplified using the similarity transformation and solved efficiently using the finite difference method. Concentration dependent viscosity and the binary diffusivity of the coating liquid are used in the analysis. The time variational velocity components of the coating liquid and the film thickness are analyzed according to the various spin speed. When the evaporation is considered, the flow decease in the early times due to the increase of the viscosity and the resultant flow resistance. Effects of the two film thinning mechanism, the flow-out and evaporation are also considered in the analysis.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 춘계학술대회 논문집
• /
• pp.783-791
• /
• 2000

Increasing demands in productivity are propelling the development of new manufacturing methods like hard machining, high speed cutting (HSC) or machining of difficult to machine materials. In these processes the toois are subjected to very severe mechanical, tribological and thermal loads. They fail prematurely by abrasion, cratering, edge breakage and cold welding. The performance of such tools will be enhanced by better and more wear resistant coatings. The development of these new coatings shows a clear trend towards complex multi-component and multi-layer configurations. TiAIN multilayer coating belongs to these coatings for the new cutting tool generation. This paper tries to explain the benefits of the new coatings. TiAIN multilayer coating offers the following advantages: reduction of manufacturing costs. boost productivity, and lower coolant procurement, conditioning and disposal costs.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.401-406
• /
• 2005

In this paper, both effect of TiN-coating and effect of temperature in TiN-coating by arc ion plating on surface characteristics of TiN coated SKH51 steel are investigated by experiments. Hardness, surface roughness, TiN coating thickness and adsorption force are measured in order to evaluate the effects. For evaluation of the experimental data, the two-way ANOVA method is used. It is concluded that the furnace temperature in the rang of $400^{\circ}C\~500^{\circ}C$ in AIP processing has very little influence on the TiN coating of the SKH51 steels.

• 한국표면공학회지
• /
• 제34권4호
• /
• pp.337-341
• /
• 2001

TiN coating of high speed end mill is recently generalized. The study of coating layer using ion plating is mainly about the coating method and the why of the longer life of coated tools. In CNC machning process, metal cutting isn't carry out until the tools including the end-mill and so on are fractured. Namely, it is difficult precision processing when the cutting force of the cutting tool is near the limit the fracture cutting force. So, the estimate of the life by wear and fracture is important. Therefore, this study is about the method to estimate the capacity of the coating layer in relation to the tendency of cutting force and the influence of the cutting capacity of coated end-mill by the condition N2, Ar, temperature. The cutting length is in inverse proportion to the cutting force ratio. So, the life of the TiN coated end mill can be predicated by the ratio of the increase of the cutting force.

• 한국산학기술학회논문지
• /
• 제13권2호
• /
• pp.471-477
• /
• 2012

SCM420재질의 기어를 담금질을 실시한 후 초경호브(Hob)에 PACVD 코팅처리 후 표면경도가 높은 표면(HRC 60)을 절삭하였다. 코팅처리 없이 난삭재(難削材)로 분류되는 경도가 큰것, 경한 물질을 포함한 것, 강도가 높은 것에 공구수명과 생산성을 향상에는 한계성을 가지고 있다. 이를 개선하기 위해 초경호브에 TiCN코팅처리 전후에 대하여 Skiving 절삭으로 코팅처리 한 호브가 가공성이 좋고, 공구마멸이 적어, 공구수명이 2.5배 증가하는 결과를 얻었다. 실험은 CNC 스카이빙 호빙머신을 이용하여 습식절삭으로 절삭속도와 이송량으로 다양한 조건을 적용하여 공구마멸과 표면거칠기 데이터를 얻었다. 실험결과 조건 2에서(V=200m/min F=0.7mm/rev) Cutting speed가 절삭표면에 Feed Mark가 미세하고, 표면거칠기는 Rmax $4.7{\mu}m$(Ra $1.19{\mu}m$)의 데이터를 얻었다.

• Corrosion Science and Technology
• /
• 제9권3호
• /
• pp.105-108
• /
• 2010

The product specification of the Continuous Hot Dip Galvanizing Line (CGL) changes and varies constantly with different customers' requirements, especially in the zinc coating weight which is from 30 to 150 g/$m^2$ on each side. Since the coating weight of zinc changes often, it is very important to reduce time spent in the transfer of target values changed for low production cost and yield loss. The No.2 CGL in China Steel Corporation (CSC) has improved the control of the air knife which is designed by Siemens VAI. CSC proposed an experiment design which is an $L_9(3^4)$ orthogonal array to find the relations between zinc coating weight and the process parameters, such as the line speed, air pressure, gap of air knife and air knife position. A non-linear regression formula was derived from the experimental results and applied in the mathematical model. A new air knife feedforward control system, which is coupled with the regression formula, the air knife control system and the process computer, is implemented into the line. The practical plant operation results have been presented to show the transfer time is obviously shortened while zinc coating weight target changing and the product rejected ratio caused by zinc coating weight out of specification is significantly reduced from 0.5% to 0.15 %.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제33회 춘계학술대회 개최
• /
• pp.236-242
• /
• 2001

In this paper the effect of bump compliance, load, and the number of pad on the lift-off speed is studied. When the load is greater and bump compliance lower, the shaft is lifted off at higher rotating speed. And when the load is applied near the center of pad, lift-off speed is lower. When the number of pad increases, the lift-off speed is higher. The lift-off characteristics can be used to lengthen the life time of the coating and design the rotating machinery supported by bump bearings.

• 한국재료학회지
• /
• 제25권5호
• /
• pp.226-232
• /
• 2015

본 연구에서는 손상된 알루미늄 금형의 복원을 위해 고온플라즈마 용사법을 이용하여 금형의 표면에 $Al/Al_2O_3$ 혼합분말을 용사한 후 코팅층과 모재의 증착강도에 대한 평가를 수행하였다. 증착강도의 평가는 분사노즐의 이동속도, 순수한 알루미늄 bond coat 층의 유무에 따라 평가되었으며, bond coat 층을 생성시키지 않았을 때, 코팅층의 두께는 열팽창에 의한 잔류인장응력의 감소를 위해 두껍지 않아야 하지만 일정두께 이상이 되어야 최대의 증착강도를 얻을 수 있음이 나타났다. 또한 순수한 알루미늄 bond coat 층은 내부 결함이 없는 응고된 금속이기 때문에 두께에 따른 증착강도의 영향을 그대로 받아 두께가 두꺼울수록 bond coat 층을 생성시키지 않은 시험편보다 증착강도가 매우 낮게 측정되었다. 반면, 가장 얇게 bond coating 된 시험편 Bc3(3회의 bond coating층과 분사건의 이동속도가 20 cm/sec인 시험편) 는 bond coating을 하지 않은 시험편 중 가장 높은 증착강도를 가지는 시험편 Wbc20(bond coating층이 없고 분사건의 이동속도가 20 cm/sec인 시험편)보다 약 2배 이상증착강도가 향상되었다. 따라서 금형의 복원시에 중간층의 형성이 반드시 필요하며, 이는 코팅층의 잔류 인장응력을 보완시키며 고인성의 순수한 알루미늄과 같은 코팅층과 유사한 층을 코팅하는 것이 필요한 것으로 사료된다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.416-416
• /
• 2016

Organic-inorganic metal halide perovskite solar cells have received attention because it has a number of advantages with excellent light harvesting, high carrier mobility, and facile solution processability and also recorded recently power conversion efficiency (PCEs) of over 20%. The major issue on perovskite solar cells have been reached the limit of small area laboratory scale devices produced using fabrication techniques such as spin coating and physical vapor deposition which are incompatible with low-cost and large area fabrication of perovskite solar cells using printing and coating techniques. To solution these problems, we have investigated the feasibility of achieving fully printable perovskite solar cells by the blade-coating technique. The blade-coating fabrication has been widely used to fabricate organic solar cells (OSCs) and is proven to be a simple, environment-friendly, and low-cost method for the solution-processed photovoltaic. Moreover, the film morphology control in the blade-coating method is much easier than the spray coating and roll-to-roll printing; high-quality photoactive layers with controllable thickness can be performed by using a precisely polished blade with low surface roughness and coating gap control between blade and coating substrate[1]. In order to fabricate perovskite devices with good efficiency, one of the main factors in printed electronic processing is the fabrication of thin films with controlled morphology, high surface coverage and minimum pinholes for high performance, printed thin film perovskite solar cells. Charge dissociation efficiency, charge transport and diffusion length of charge species are dependent on the crystallinity of the film [2]. We fabricated the printed perovskite solar cells with large area and flexible by the bar-coating. The morphology of printed film could be closely related with the condition of the bar-coating technique such as coating speed, concentration and amount of solution, drying condition, and suitable film thickness was also studied by using the optical analysis with SEM. Electrical performance of printed devices is gives hysteresis and efficiency distribution.