• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.10
• /
• pp.815-819
• /
• 1998

The silicon-nirtide membrane structure for IR sensor was fabricated through the etching and the direct bonding. The PRO($PbTiO_3$ ) layer for a IR detection was coated on the membrane and its characteristics were measured. The a attack of PTO layer during the etching of silicon wafer as well as the thermal isolation of the IR detection layer were eliminated through the method of bonding/etching of silicon wafer. The surface roughness of the membrane was measured by AFM, the micro voids and the non-contacted area were inspected by the PTO layer were measured, too.

• Journal of Magnetics
• /
• v.14 no.1
• /
• pp.31-35
• /
• 2009

Herein, the Magneto-Optical Kerr Effect (MOKE) signal enhancement in nanostructures in investigated. It is well known that the MOKE signals of ferromagnetic thin films are enhanced with an additional dielectric layer due to multiple reflections. The MOKE signal is modulated with the additional dielectric layer thickness and is at a maximum when reflectivity is at a minimum. This is not always true in the nanostructures due to the contribution from the non-magnetic substrate portion, especially when substrate reflectivity is minimized and the dependence of the additional dielectric layer thickness for the nanostructure is changed in the case of the continuous thin film. We showed that the MOKE signal for nanostructures could be enhanced with a properly designed, dielectric layer in addition to the anti-reflection coated substrates.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.321-321
• /
• 2010

The PEDOT:PSS layer is usually used as hole transporting layer for the polymer bulk heterojunction solar cells. However, the interface between ITO and PEDOT:PSS is not stable and the chemical reaction between ITO and PEDOT can result in degraded device performance. We used the tungsten oxides as a hole transport layer by spin-coating. The $WO_3$ nanoparticles were well dispersed in ammonium hydroxide and deionized water and formed thin layer on the ITO anode. We found that $WO_3$ surface is more hydrophobic than the bare ITO or PEDOT:PSS-coated surfaces. The hydrophobic surfaces promote an ordered growth of P3HT films. A higher degree of P3HT ordering is expected to improve the hole mobility and the lifetime of the device using the tungsten oxide showed better stability compared to the device using the PEDOT:PSS.

• ETRI Journal
• /
• v.44 no.1
• /
• pp.147-154
• /
• 2022

We demonstrate a new double-layer structure for stretchable interconnects, where the top surface of a serpentine polyimide support is coated with a thin eutectic gallium-indium liquid metal layer. Because the liquid metal layer is constantly fixed on the solid serpentine body in this liquid-on-solid structure, the overall stretching is accomplished by widening the solid frame itself, with little variation in the total length and cross-sectional area of the current path. Therefore, we can achieve both invariant resistance and infinite fatigue life by combining the stretchable configuration of the underlying body with the freely deformable nature of the top liquid conductor. Further, we fabricated various types of double-layer interconnects as narrow as 10 ㎛ using the roll-painting and lift-off patterning technique based on conventional photolithography and quantitatively validated their beneficial properties. The new interconnecting structure is expected to be widely used in applications requiring high-performance and high-density stretchable circuits owing to its superior reliability and capability to be monolithically integrated with thin-film devices.

• Tribology and Lubricants
• /
• v.5 no.2
• /
• pp.42-47
• /
• 1989

The thermal behaviour of layerd solids, typified in practice by surface coated materials, is evaluated for the specific case of a fast moving heat source. This is intended to represent the particular instance of solids in sliding contact and the consequences of friction. The finite difference method has been utilised to establish the temperature distributions at the surface and also the sub-surface region for coating materials which are either less conductive or more conductive than the substrate to which they are attached. The effects of variation in layer thickness, and also the load, speed and friction coefficient, are evaluated.

• 한국초전도학회:학술대회논문집
• /
• 2009.07a
• /
• pp.94-94
• /
• 2009

• Transactions on Electrical and Electronic Materials
• /
• v.1 no.3
• /
• pp.23-28
• /
• 2000

A block-oxide layer was formed on the surface of Cu-based leadframe by chamical oxidation method in order to enhance the adhesion strength between Cu-based leadframe and epoxy molding compound (EMC) Using sandwiched double cantilever beam (SDCB) specimens, the adesion strength was measured in terms of interfacial fracture toughness, G$\sub$IC//Results showed that the black-oxide layer was composed of two kinds of layers: pebble-like Cu$_2$O layer and acicular CuO layer, At the initial stage of oxidation the Cu$_2$O layer was preferentially formed and thickened up to around 200 nm whithin 1 minute of the oxidation time. Then the CuO layer started to from atop of the Cu$_2$O layer and thickened up to around 1300 nm until 20 minutes. As soon as the CuO layer formed, the thickness of Cu$_2$O layer began to reduce and finally reached to around 150 nm. The pre-cleaned and the Cu$_2$O coated leadframes showed almost no adhesion of EMC, however, as the CuO precipitates appeared and became continuous, G$\sub$IC/ increased up to around 80 J/㎡. Further oxidation raised G$\sub$IC/ up. to around 100 J/㎡.

• Archives of Pharmacal Research
• /
• v.25 no.6
• /
• pp.964-968
• /
• 2002

Colon drug delivery is advantageous in the treatment of colonic disease and oral delivery of drugs unstable or suceptible to enzymatic degradation in upper GI tract. In this study, multilayer coated system that is resistant to gastric and small intestinal conditions but can be easily degraded by colonic bacterial enzymes was designed to achieve effective colon delivery of prednisolone. Variously coated tablets containing prednisolone were fabricated using chitosan and cellulose acetate phthalate (CAP) as coating materials. Release aspects of prednisolone in simulated gastrointestinal fluid and rat colonic extracts (CERM) were investigated. Also, colonic bacterial degradation study of chitosan was performed in CERM. From these results, a three layer (CAP/Chitosan/CAP) coated system exhibited gastric and small intestinal resistance to the release of prednisolone in vitro most effectively. The rapid increase of prednisolone in CERM was revealed as due to the degradation of the chitosan membrane by bacterial enzymes. The designed system could be used potentially used as a carrier for colon delivery of prednisolone by regulating drug release in stomach and the small intestine.

• Tribology and Lubricants
• /
• v.14 no.2
• /
• pp.35-41
• /
• 1998

The $WS_2$ solid lubricant synthesized through the vapour phase transport method was coated on the commercial bearing steel (SUJ 2) substrate, and the tribological behaviour of the lubricant was investigated using a ball-on-disk type tester. The $WS_2$ powder was spray-coated at room temperature using compressed air, and the change of friction coefficient was examined in various conditions, i.e., specimen configuration, atmosphere (air and nitrogen), applied load and rotating speed. $WS_2$ coated ball and disk showed the optimum friction coefficient of 0.07 and wear life of 45,000 cycles in the nitrogen atmosphere under 0.3 kgf and 100 rpm, whereas relatively high coefficient of 0.13 and reduced wear life of 4,000 cycles were observed in air atmosphere. The effect of rotating speed on the friction coefficient was not observed both in nitrogen and in air atmospheres. This confirmed that the spray-coated $WS_2$ solid lubricant was effective in reducing the friction coefficient and improving wear life in nitrogen atmosphere, and the oxygen and moisture existing in air could seriously deteriorate the lubrication effect of $WS_2$ coating layer.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.2
• /
• pp.8-15
• /
• 2014

A novel antibacterial paper coated with chitosan-based silver (Ag) nanocomposite prepared by green synthesis has been investigated for a wide range of application in food, agricultural and medical packaging. Green synthesis of Ag nanoparticles (AgNPs) was carried out by a chemical reaction involving a mixture of chitosan-silver nitrate (AgNO3) in an autoclave at 15 psi, $121^{\circ}C$, for 15-120 sec. AgNPs and their formation in chitosan were confirmed by both UV-Vis spectroscopy and transmission electron microscope (TEM). Fourier transform infrared spectroscopy (FTIR) study showed that free amino groups in chitosan act as an effective reductant and AgNPs stabilizer. Antibacterial test of coated paper with as-prepared chitosan-AgNPs was performed qualitatively against E. coli based on the formation of halo zones around coated papers and it was shown to be effective in suppressing the growth of E. coli with increasing Ag contents in coating layer.