• Structural Engineering and Mechanics
• /
• 제62권3호
• /
• pp.357-364
• /
• 2017

This paper presents the results of a study that investigated the improvement of the mechanical properties of coarse and fine recycled asphalt pavement (RAP) produced by adding silica fume (SF) with contents of 5%, 10%, and 15% by total weight of the cement. The coarse and fine natural aggregate (NA) were replaced by RAP with replacement ratio of 20%, 40% and 60% by the total weight of NA. In addition, SF was added to NA concrete mixes as a control for comparison. Twenty eight mixes were produced and tested for compressive, splitting tensile and flexural strength at the age of 28 days. The results show that the mechanical properties decrease with as the content of RAP increases. And the decrease in the compressive strength was more in the fine RAP mixes compared to the coarse RAP mixes, while the decrease in the splitting tensile and flexural strength was almost the same in both mixes. Furthermore, using SF enhances the mechanical properties of RAP mixes where the optimum content of SF was found to be 10%, and the mechanical properties enhancement of coarse RAP were better than fine RAP mixes. Accordingly, the RAP has the potential to be used in the concrete pavements or in other low strength construction applications in order to reduce the negative impact of RAP on the environment and human health.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계 학술발표회 논문집(II)
• /
• pp.161-164
• /
• 2006

The main objective of this study was to evaluated the physical properties of concrete with substitution ratio of recycled fine aggregate and recycled coarse aggregate made of waste concrete. The replacement ratios of recycled coarse and fine aggregate decided 0%, 30%, 40% and 50% respectively to get the deregulate of floor space Index. The test result showed that compression strength of cylinder mold decrease with the substitution ratio increase but its strength of replaced recycled fine aggregate higher than OPC.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1995년도 추계학술대회 논문집
• /
• pp.18-23
• /
• 1995

The study was carried out to develope a precision positioning apparatus, consisting of DC servo motor and piezoelectric actuator. This system is composed of fine and coarse apparatus, measurement system and control system, Piezoelectric actuator is designed for fine positioning. Coarse positioning using lead screw is drived by DC servo motor. Control system output a signal from laser interferometer and microsense to amplifier of DC servo motor and piezoelectric actuator after digital signal processing(DSP). Resolution of this apparatus measure with laser interferometor and microsense

• 한국환경과학회지
• /
• 제12권10호
• /
• pp.1043-1054
• /
• 2003

During the period from April to September 2002, the size distributions of ambient aerosol were measured at the coastal site at Hamduk in Jeju Island. Na$\^$+/, K$\^$+/, Mg$\^$2+/, Ca$\^$2+/and Cl$\^$-/ exhibited mostly a bimodal coarse mode size distribution, while ammonium and sulfate were mainly in the fine size range, with maximum at around 0.54$\mu\textrm{m}$. The average molar concentration ratio of ammonium to sulfate for fine particles was equal to 2.0${\pm}$0.9. Nitrate was evenly found in both the coarse and fine modes. Elements like Al, Fe, Cu, Mg, Na, Ti, Sr and Mn were dominant in coarse particles, with the maximum at around 5.25$\mu\textrm{m}$. S and Pb were mainly in the submicrometer size range. Other elements with a fine and coarse modes were V, Ni, Cu, Ba and Mo. The patterns of the size distributions of trace elements measured at the downtown in Jeju City were very similar to those at the coastal site in Hamduk. However, the amplitude of size fractional concentrations at Jeju City was narrower than that at Hamduk. While the mass median diameters for the chemical species originated from the natural origin such as marine and crust were relatively large, those for ammonium, sulfate, S and Pb were very small.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2015년도 춘계 학술논문 발표대회
• /
• pp.71-72
• /
• 2015

As this study is the one related to the ultra high strength concrete essentially used for high rise buildings, it has analyzed on the flowability of ultra high strength concrete according to the variation of coarse aggregate and fine aggregate. The coarse aggregate was planned as two types including Granite Aggregate (GA) and crushed coarse Limestone Aggregate (LA) while fine aggregate was planned as four types including Sea Sand (SS), Limestone Crushed Fine Aggregates (LFA), Electric Arc Furnace Oxidizing Slag Aggregates (EFA) and Crushed Sand (CS) to perform experiment with a total of eight variables. As a result of analyzing slump flow, 500mm concentration time, U-Box and L-Flow, etc. among the characteristics of fresh concrete, a mix using LA+LFA is determined to show high flowability in case of applying ultra high strength concrete.

• 한국세라믹학회지
• /
• 제43권12호
• /
• pp.768-774
• /
• 2006

The microstructure of Ni-YSZ cermets was controlled with fine and coarse starting powders (NiO and YSZ) to obtain a optimum strong and conductive tubular anode support for SOFCs. Three types of cermets with different microstructures, i.e., coarse Ni-fine YSZ, fine Ni-coarse YSZ, and fine Ni-fine YSZ, were fabricated to investigate their electrical and mechanical properties. The cermets from fine NiO powder showed high electrical conductivity due to the enhanced percolation of Ni particles. The cermet by foe Ni and coarse YSZ showed excellent electrical conductivity (>1000 S/cm) despite its high porosity $(\sim40%)$ but it showed poor mechanical strength due to the lack of percolation by YSZ particles and due to large pores. Thus fine NiO and YSZ powders were used to make strong and conductive Ni-YSZ support tube by extrusion. The microstructure of the anode tube was modified by the amount of polymeric additives and carbon black, a pore former. Ni-YSZ tube (porosity $\sim34%$) with the finer microstructure showed better performance both in electrical conductivity (>1000 S/cm) and fracture strength $(\sim140\;MPa)$. Either flat or circular NiO-YSZ tubes with the length from 20 to 40cm were successfully fabricated with the optimized composition of materials and polymeric additives.

• 대한인간공학회:학술대회논문집
• /
• 대한인간공학회 1996년도 추계학술대회논문집
• /
• pp.197-205
• /
• 1996

Unification of neural network with a hierarchical pattern recognition is presented for recognizing large set of objects. A two-step identification procedure is developed for pattern recognition: coarse and fine identification. The coarse identification is designed for finding a class of object while the fine identification procedure is to identify a specific object. During the training phase a course neural network is trained for clustering larger set of reference objects into a number of groups. For training a fine neural network, expert neural network is also trained to identify a specific object within a group. The presented idea can be interpreted as two step identification. Experimental results are given to verify the proposed methodology.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1990년도 한국자동제어학술회의논문집(국제학술편); KOEX, Seoul; 26-27 Oct. 1990
• /
• pp.1312-1315
• /
• 1990

Nanometer positioning control with high velocity and long stroke is discussed. A one-axis stage mechanism driven by an AC linear motor and guided by a rolling ball guide has been constructed. Coarse and fine position controls are designed by using nonlinear dynamics of the rolling guide. Switching from coarse positioning to fine positioning is studied.

• 한국지능시스템학회논문지
• /
• 제9권6호
• /
• pp.598-604
• /
• 1999

본 논문에서는 능동형자기베어링(Active Magnetic Bearing AMB)시스템의 제어를 위한 새로운 퍼지제어 알고리즘을 제안한다. 이 방법은 AMB 시스템의 비선형 특성을 효과적으로 다루기 위하여 Joh등[4,5]이 제안한 LMI에 근거한 PDC 알고리즘과 퍼지 싱글톤을 사용하는 Mamdani형의 퍼지제어기를 복합한다. 이들은 각각 fine mode control과 coarse mode control이라고 구분하였다. coarse mode control은 회전축의 위치에러가 큰 경우 빠른 중심복귀 응답특성을 보이며 fine mode control은 회전축의 위치에러가 작을 때 요구되는 과도응답특성을 제공한다. 본 논에서 제안된 방법은 그성능을 입증하기 위하여 AMB 시스템의 제어에 적용되었으며 선형제어기와 일반적인 PDC 알고리즘으로 제어된 결과와의 비교를 통해 제안된 방법의 우수성을 보인다.

• 자원리싸이클링
• /
• 제24권5호
• /
• pp.63-71
• /
• 2015

본 연구는 재생 굵은골재와 산업부산물인 급냉 제강슬래그 잔골재를 이용한 친환경 재생 콘크리트의 재료적 특성을 파악하고 적정 혼합비를 도출하는데 그 목적이 있다. 이를 위해서 재생 굵은골재의 치환율은 30%에서 50%까지 증가시켰으며, 급냉 제강슬래그 잔골재는 10%에서 50%까지 증가시켜서 물성실험을 수행하였다. 그 결과, 재생골재의 치환율이 증가함에 따라 강도가 감소하였으나 급냉 제강슬래그 잔골재의 혼입율을 증가함에 따라 강도가 증가됨을 알 수 있었다. 더불어 급냉 제강슬래그 잔골재의 적정 치환율은 압축강도 및 탄성계수 등을 고려했을때 20~30%로 판단되며, 재생 굵은골재의 치환율 증가에도 도움이 될 것으로 사료된다.