• Korean Journal of Materials Research
• /
• 제26권3호
• /
• pp.117-122
• /
• 2016

White organic light-emitting diodes with a structure of indium-tin-oxide [ITO]/N,N-diphenyl-N,N-bis-[4-(phenylm-tolvlamino)-phenyl]-biphenyl-4,4-diamine [DNTPD]/[2,3-f:2, 2-h]quinoxaline-2,3,6,7,10,11-hexacarbonitrile [HATCN]/1,1-bis(di-4-poly-aminophenyl) cyclo -hexane [TAPC]/emission layers doped with three color dopants/4,7-diphenyl-1,10-phenanthroline [Bphen]/$Cs_2CO_3$/Al were fabricated and evaluated. In the emission layer [EML], N,N-dicarbazolyl-3,5-benzene [mCP] was used as a single host and bis(2-phenyl quinolinato)-acetylacetonate iridium(III) [Ir(pq)2acac]/fac-tris(2-phenylpyridinato) iridium(III) $[Ir(ppy)_3]$/iridium(III) bis[(4,6-di-fluoropheny)-pyridinato-N,C2] picolinate [FIrpic] were used as red/green/blue dopants, respectively. The fabricated devices were divided into five types (D1, D2, D3, D4, D5) according to the structure of the emission layer. The electroluminescence spectra showed three peak emissions at the wavelengths of blue (472~473 nm), green (495~500 nm), and red (589~595 nm). Among the fabricated devices, the device of D1 doped in a mixed fashion with a single emission layer showed the highest values of luminance and quantum efficiency at the given voltage. However, the emission color of D1 was not pure white but orange, with Commission Internationale de L'Eclairage [CIE] coordinates of (x = 0.41~0.45, y = 0.41) depending on the applied voltages. On the other hand, device D5, with a double emission layer of $mCP:[Ir(pq)_2acac(3%)+Ir(ppy)_3(0.5%)]$/mCP:[FIrpic(10%)], showed a nearly pure white color with CIE coordinates of (x = 0.34~0.35, y = 0.35~0.37) under applied voltage in the range of 6~10 V. The luminance and quantum efficiency of D5 were $17,160cd/m^2$ and 3.8% at 10 V, respectively.

• Journal of Technologic Dentistry
• /
• 제11권1호
• /
• pp.35-45
• /
• 1989

This study was carried out from June, 20, to October 22, 1988, for the purpose of researching on the complaint ratio of Respiratory symptoms of the dental laboratory technicians in Seoul. In this study, aiming to find out complaint ratio of respiratory symptoms of the dental laboratory, SNU-81-AL were applied, at random, to 193 dental laboratory technicians at 39 dental laboratories, as the research group, and to 178 clinical laboratory technicians at 10 general hospitals, as the control group, and above two groups were compared with each other. The following results were obtained from this research. 1. The quantity of respirable dust under 5$\mu$m measured at the dental laborartories was, on an average as well, 5$mg/m^3$-minimum 1.56$mg/m^3$), and the density of CO was, on an average as well, 5.0ppm(Mx 7.0-Mn 3.0). 2. The complaint ratio of five main respiratory symptoms(cough, phlegm, wheezing, nasal catarrh & cold, breathlessness) was, on an average, 44.3% at the dental laboratory technicians, phlegm was the major symptom complained by the greatest number of the technicians. 22.4% of the clinical laboratory technicians complained above 5 main respiratory symptoms, nassal catarrh & cold was the mostly complained symptoms among them. There showed a consideraly significant difference at the complaint ratio between the above 2 occupations(P<0.005). 3. There showed no paticular significant difference between male and female, at the complaint ratio of the dental laboratory technicians. However, there showed a considerable significant difference according to their sexuality, in case of the clinical laboratory technicians. 4. Considered from th view point of age, the highest age group was 20-29 with its average 48.5%, in case of dental laboratory technicians. The highest age group among the clinical laboratory technicians was over 40 age with its 28.7%. There showed no particular significant differences between to tow occupations. 5. Considered from the view point of work period, the highest work period group was 0-3 years with average 47.8%, in case of dental laboratory The highest work period group among the clinical laboratory technicians was 16 years with its 25.2%. There showed no particuar significant differences between the two occupations. 6. Considered from the view point of smoking, phlegm was complained by much more smokers than non-smokers, in both occupations. In case of non-smokers, many complained about nassal catarrh & cold. There showed no particular significant differences between the smokers and the non-smokers.

• Journal of the Korean GEO-environmental Society
• /
• 제6권2호
• /
• pp.61-73
• /
• 2005

In Korea, none of the design methods, which can consider the properties of hard soil, weathered rock and the condition of construction, are suggested. Therefore, the properties of geomaterial are simply classified into three categories such as sand, clay and rock for the resistance estimation of axially loaded drilled shafts in Korea. However, in America, O'Neill et al.(1996) presented design methods for a new category of geomaterial which is between soil and rock termed "intermediate geomaterials, IGM's". And FHWA(1999) adapted above most complete classification of geomaterials in its design manual. However, in Korea, these properties are depended on the engineer's judgement, the weathered rocks may be counted as soils, although they may be referred to as IGM's in America. In this study, the applicability of IGM method was investigated through the two construction sites in Korea. For the comparison, two geomaterial properties are applied, respectively. The one was sound soil condition and the other was IGM condition and classical design method and IGM method were applied, respectively. The results showed that the predicted bearing capacities of drilled shafts with IGM's were larger than the predicted values by the classical design method with sound soil condition.

• Journal of Electrical Engineering and Technology
• /
• 제13권4호
• /
• pp.1638-1643
• /
• 2018

Multi-layer ceramic capacitors as decoupling capacitor were fabricated by dielectric composition with a high dielectric constant. The fabricated decoupling capacitors were embedded in the PCB of the 10G RF transceiver module and evaluated for the characteristics of electrical noise by the level of AC input voltage. In order to further improve the electrical properties of the $BaTiO_3$ based composite, glass frit, MgO, $Y_2O_3$, $Mn_3O$, $V_2O_5$, $BaCO_3$, $SiO_2$, and $Al_2O_3$ were used as additives. The electrical properties of the composites were determined by various amounts of additives and optimum sintering temperature. As a result of the optimized composite, it was possible to obtain a density of $5.77g/cm^3$, a dielectric constant of 1994, and an insulation resistance of $2.91{\times}10^{12}{\Omega}$ at an additive content of 5wt% and a sintering temperature of $1250^{\circ}C$. After forming a $2.5{\mu}m$ green sheet using the doctor blade method, a total of 77 layers were laminated and sintered at $1180^{\circ}C$. A decoupling capacitor with a size of $0.6mm(W){\times}0.3mm(L){\times}0.3mm(T)$ (width, length and thickness, respectively) and a capacitance of 100 nF was embedded using a PCB process for the 10G RF Transceiver modules. In the range of AC input voltage 400mmV @ 500kHz to 2200mV @ 900kHz, the embedded 10G RF Transceiver modules evaluated that it has better electrical performance than the non-embedded modules.

• Journal of Navigation and Port Research
• /
• 제41권6호
• /
• pp.415-422
• /
• 2017

In a situation where there is excessive competition among logistics centers due to the low price of logistics centers for attracting freight volume, the conditions provided by the logistics centers are similar. Therefore, in order to determine the logistics center, we want to find out what kind of differentiated service the shippers desire, as well as what level of service they want in addition to al ow price. There are currently no studies about the service quality of logistics centers. The components of the service quality of the logistics center were extracted by applying them to the logistics center based on the existing service quality theory. Factor analysis revealed five dimensions of service quality: tangibility, reliability, empathy, assurance, and know-how. It was found that service quality had a statistically significant influence on customer satisfaction, from the investigation of the causal effect relationship. In addition, 'Know-How' among these factors has more influence on customer satisfaction, so it is important to accumulate differentiated 'Know-How' only in logistics centers.

• 한국해양학회지
• /
• 제7권1호
• /
• pp.24-45
• /
• 1972

The Han River is an important water source in Seoul and neighbouring districts, for public and industrial supply, and for agriculture and fishery. Nowadays, more than six million inhabitants are supplied withe water from this river. The total length of the river is 470km, and has 17 10$\^$9/㎥ an average annual flow. The hydrographic characteristics at Seoul are 653㎥/sec in an average flow, 4,608㎥/sec in the maximum average flow, and 201㎥/sec in the minimum average flow. These are influenced in some degree by snowmelt in early spring, and greatly by the flood during summer. For the pollution problems, the periods of low flow are critical ones. As a rule they occur around the months November through June. Nowadays, most of the sewage from towns and industries is discharged untreated. Apart from domestic and industrial sewages, there are some discharges of mineral matter by mines in the upriver region. In general, water quality of the Han River is kept very clean and healthy until Kwangnaru of the upper region of Seoul. A large pollution, however, is received in the downstream by the domestic and industrial sewages of Seoul. It can be seen that dissolved oxygen, COD and BOD$\sub$5/ diminish markedly, and the intensity of almost every water parameter of the river continues to increase. Comparison of the figures for 1971 derived from a sampling point 40km downstream of Kwangnaru leads to the conclusion that hardness, Ca and Mg were no changed; alkalinity, Si and soluble- Fe were slightly increased; CO$\sub$2/, acidity, Cl, NO$\sub$2/-N, Cu, Zn and Al were increased in 2 and 3 times; total residue, total ignitious residue, COD, BOD$\sub$5/, NH$\sub$4/-N, PO$\sub$4/-P, Mn, Pb and total-Fe were increased in 4 to 7 times; and SO$\sub$4/, particulate-Fe and Cd were increased in 10 to 11 times. On the other hand, coliforms were increased in 650 times; fecal coliforms in 365 times; enterococci and total plate counts in 30 times, respectively. In view points of water quality standards, the down Han River water is now leveling out in Cd, coliforms and fecal coliforms for the agricultural use; in dissolved oxygen and some trace elements (Cu, Zn, Pb and Cd) for the fishery use; in ammonia, COD, BOD$\sub$5/, and Cd for the drinking use.

• Korean Journal of Food Science and Technology
• /
• 제32권2호
• /
• pp.317-322
• /
• 2000

This study examined the effect of nitrogen$(N_2)$ gas packing and ${\gamma}-oryzanol$ treatment on the shelf life of Yukwa(Korean traditional snack). Yukwa were stored with $N_2$ gas packing(AN), $N_2$ gas packing with ${\gamma}-oryzanol$ treatment(ANA), and PE film packing with air(PE) for 20 days at $60^{\circ}C$. They were evaluated by POV, AV, conjugated diene, hexanal, color and sensory characteristics. The POV, AV and conjugated diene content increased abruptly in PE and AN, but increased slowly in ANA with prolonged storage. Higher sensory scores for Yukwa were found in ANA as compared to those in PE and AN. Hexanal content, yellowness and redness in AN were higher than those in ANA and PE. The moisture content, which is supposed to be related with browning of Yukwa, was 3 times higher in AN than that in PE. Oxygen content of each Yukwa pack, even in $N_2$ gas packing, increased remarkably as storage period increased because their highly porous, fragile and syrup-coated structure resulted in incomplete degassing before $N_2$ gas was flushed into package. Consequently, $N_2$ gas packing was inefficient, but $N_2$ gas packing combined with antioxidant(such as ${\gamma}-oryzanol$) treatment was effective for the extension of shelf life of Yukwa.

• Restorative Dentistry and Endodontics
• /
• 제23권1호
• /
• pp.183-196
• /
• 1998

The purpose of this study was to determine the effect of bleaching technique on the shear bond strength of esthetic restorative materials to bovine enamel. The bleaching agent was used 35% $H_2O_2$(Hi-Lite, Shofu, U.S.A.). Experimental groups were divided into two divisions as group A and B. Experimental A groups for the effect of number of bleaching were as follows ; Group Al : no bleaching Group A2 : bleaching 1 time ( for 5 minutes ) Group A3 : bleaching 3 times ( each for 5 minutes ) Group A4 : bleaching 6 times ( each for 5 minutes ) Group A5 : bleaching 9 times ( each for 5 minutes ) Experimental B groups for the effect of storage period in artificial saliva were as follows ; Group B1 : not stored in artificial saliva after bleaching Group B2 : stored in artificial saliva for 1 day after bleaching Group B3 : stored in artificial saliva for 1 week after bleaching Group B4 : stored in artificial saliva for 2 weeks after bleaching Group B5 : stored in artificial saliva for 4 weeks after bleaching Composite resin and glass ionomer cement were bonded to all specimens, and the shear bond strength between enamel and r~storative material were measured in Instron Universal Testing Machine(Instron, 4467, U.S.A,), Additionally, the bleached enamel specimens were examed after etching with 37.4% $H_3PO_4$ for 1 min under SEM(S-2300, Hitachi Co., Japan) to observe the effect of bleaching procedure on enamel surface morphology. The result were as follows ; 1. In SEM findings, bleached bovine enamel was found to be superficially rough. 2. In bleached bovine enamel, the effect of acid etching was reduced with the increase of number of bleaching. 3. The mean shear bond strength of composite resin and glass ionomer cement to bleached enamel surface tended to be lower than those to non-bleached enamel surface. 4. With the increase of number of bleaching, the shear bond strength of composite resin and glass ionomer cement to bleached enamel were progressively decreased. 5. Increasing the, storage period in artificial saliva after bleaching, the shear bond strength of composite resin and glass ionomer cement to bleached enamel were progressively increased. 6. The mean shear bond strength of glass ionomer cement to bleached bovine enamel tended to be clearly lower than that of composite resin.

• Resources Recycling
• /
• 제29권1호
• /
• pp.81-88
• /
• 2020

Recovery of gallium and indium from waste light emitting diodes has been emphasized gradually owing to high content of gallium and indium. This study was established the recovery of gallium (Ga³⁺) and indium (In³⁺) from waste gallium nitride was contained in waste light-emitting diodes. The procedure was divided into the following steps; characteristic analysis, alkaline roasting, and leaching. In characteristic analysis part, the results were used as a theoretical basis for the acid leaching part, and the chemical composition of waste light emitting diodes is 70.32% Ga, 5.31% Si, 2.27% Al and 2.07% In. Secondly, with reduction of non-metallic components by alkaline roasting, gallium nitride was reacted into sodium gallium oxide, in this section, the optimal condition of alkaline roasting is that the furnace was soaked at 900℃ for 3 hours with mixing Na₂CO₃. Next, leaching of waste light emitting diodes was extremely important in the process of recovery of gallium and indium. The result of leaching efficiency was investigated on the optimal condition accounting for the acid agent, concentration of acid, the ratio of liquid and solid, and reaction time. The optimal condition of leaching procedures was carried out for 2.0M of HCl liquid-solid mass ratio of 30 ml/g in 32minutes at 25℃ and about 96.88% Ga and 96.61% In were leached.

• Geophysics and Geophysical Exploration
• /
• 제8권1호
• /
• pp.1-6
• /
• 2005

Analogue physical modelling using granular materials (i.e., sandbox experiments) has been applied with great success to a number of geological problems at various scales. Such physical experiments can also be simulated numerically with the Discrete Element Method (DEM). In this study, we apply the DEM simulation to the collision between the Indian subcontinent and the Eurasian Plate, one of the most significant current tectonic processes in the Earth. DEM simulation has been applied to various kinds of dynamic modelling, not only in structural geology but also in soil mechanics, rock mechanics, and the like. As the target of the investigation is assumed to be an assembly of many tiny particles, DEM simulation makes it possible to treat an object with large and discontinuous deformations. However, in DEM simulations, we often encounter difficulties when we examine the validity of the input parameters, since little is known about the relationship between the input parameters for each particle and the properties of the whole assembly. Therefore, in our previous studies (Yamada et al.,2002a,2002b,2002c), we were obliged to tune the input parameters by trial and error. To overcome these difficulties, we introduce a numerical biaxial test with the DEM simulation. Using the results of this numerical test, we examine the validity of the input parameters used in the collision model. The resulting collision model is quite similar to the real deformation observed in eastern Asia, and compares well with GPS data and in-situ stress data in eastern Asia.