• Journal of the Korea Institute of Building Construction
• /
• v.11 no.3
• /
• pp.247-255
• /
• 2011

Currently, there is database for per unit requirements of major construction materials in terms of energy consumption and $CO_2$ emission based on the input-output table published by the Bank of Korea in 2000, but no database for per unit requirements based on input-output tables was published in 2005 and 2007. The purpose of this study was to calculate the unit requirement values of major construction materials in terms of energy consumption and $CO_2$ emission generated by using the input-output tables published in 2005 and 2007. To estimate the unit requirement values, a database building method with the input-output tables was adopted by selecting 16 types of construction materials in wide use on construction sites. When the study results were compared with existing unit requirement values based on the input-output table of 2000, there were small discrepancies, from which it can be interpreted that the method used in the study is reasonable. Unit requirement values estimated based on input-output tables of 2005 and 2007 tended to decrease, and the highest value of energy consumption and $CO_2$ emission were found in the materials using cement and rebar.

• Journal of Welding and Joining
• /
• v.4 no.2
• /
• pp.21-29
• /
• 1986

The influence of welding heat input variation(600-900J/cm) and heat-treatment condition after welding on tensile strength of butt welded joint in $175Kg/mm^2$ strength level Maraging steel(Co-free and Co-containing) sheets was investigated on the basis of hardness distribution, microstructure of weld metal and fracture surface. The obtained main results are as follows; 1. The strength of weldment (UTS, NTS), joint efficiency showed a little decreasing tendency with the increase in welding heat input, and the elongation showed a little increasing tendency with the increase in the width of weld metal. It was considered because of the plastic constraint of the high strength base metal. 2. The strength of weldment was better in the solution treatment and aging than the aging only after welding due to the disappearance of almost denverite in weld metal. 3. The hardness distribution in weldment after welding and heat-treatment was almost similar to both Co containing and Co free Maraging steel with change in welding heat input. 4. The fracture was occurred at weld metal, and the fracture surface showed a relatively shallow dimples in both Co containing and Co free Maraging steel.

• Journal of the Korean Vacuum Society
• /
• v.2 no.2
• /
• pp.152-160
• /
• 1993

In this study, we have investigated the influence of sputtering conditions (Ar pressure input powers, substrates) on coercivity and microstructures of GdFe, Co, CoCr thin films produced by the method of DC magnetron sputtering. In GdFe films, we have observed that the Gd atomic ratio was decreased with the deposition rate, and deposition rate decreased with the pressure of Ar gas and the increased linearly with input power. It was also observed that the coercivity of thin films was increased with input power. In Co films, we have investigated the deposition was increased and the Co thin film became finer structure with the increase in the input power, was increased and the Co thin film became finer structure with the increase in the input power, and the deposition rate was decreased with the pressure of Ar gas. In CoCr films, we have investigated the effects of substrates on the coercivity $(H_c)$ and the microstructure. We have found that the substrates plays a crucial role in the microstructure and the coercivity $(H_c)$.

• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.803-806
• /
• 2004

In this paper, configuration of prototype 300kVA UPS system with unity input power factor is briefly described and a various types of rectifier for UPS application are discussed. Input LCL filter for PWM rectifier and output LC filter for PWM inverter are designed as a prototype and their principal characteristics are discussed.

• Journal of Korean Physical Therapy Science
• /
• v.22 no.1
• /
• pp.11-17
• /
• 2015

Purpose : The current study examines changes of static uprighting balance in the visual input characteristics. Method : Total 50 person(male 16, female 34) were participated in this study. They were tested with 'hole in the card' for identification of dominant eye's side, then they were divided 3 groups(both visual input group, dominant visual input group, and non-dominant visual input group). 3 groups were measured with Romberg test on the force platform device to compare the static uprighting balance characteristics ; moving distance, mean velocity, and sway area of the CoM(center of mass), during 20 seconds. Results : The results by one-way repeated measure ANOVA were as follows. In moving distance and mean velocity of CoM, non-dominant visual input group was unstable than dominant visual group and both visual input group(p<0.05). But, in sway area of CoM, significant difference was not existed statistically. Conclusion : These result can be applied to design the static uprighting balance program using visual input mediation.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1249-1253
• /
• 2004

A robust input modification approach to the control of flexible joint robot is presented. In our previous study, we developed an observer based state feedback control for the suppression of residual vibration of a robot. The control was very effective in suppressing the inherent vibration of a flexible joint robot. However it did not meet high performance requirements under high speed motion and model uncertainties. As a solution of the problem, we present an input modification method with robustness against parametric uncertainties. The main idea of the proposed input modification method is to generate a modified reference position command for fast and accurate motion of the robot. Using this proposed method we can reduce the servo delay and settling time by about 60% and substantially improve the path accuracy.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1955-1959
• /
• 2005

This paper presents a systematic analysis and a simple design of a robust adaptive control law for a class of non linear systems with modeling errors and a time-delay input. The theory for designing a robust adaptive control law based on input- output feedback linearization of non linear systems with uncertainties and a time-delay in the manipulated input by the approach of parameterized state feedback control is presented. The main advantage of this method is that the parameterized state feedback control law can effectively suppress the effect of the most parts of nonlinearities, including system uncertainties and time-delay input in the pp-coupling perturbation form and the relative order of non linear systems is not limited.

• Environmental and Resource Economics Review
• /
• v.15 no.3
• /
• pp.425-450
• /
• 2006

The index of energy intensity(energy/GDP) has been a primary policy concern since it can clarify industry sectors which use energy intensively and generate $CO_2$ emission heavily. Although energy intensity index may be suitable for estimating $CO_2$ emission from an isolated industry sector, we need an index for induced $CO_2$ emission since industrial activities are interconnected in terms of input and output. By employing Environmental Input-Output Table 2000, this paper analyses the flow of energy demand and pollutants after first estimating an induced $CO_2$ emissions from various industrial sectors and economic activities. The paper reports higher induced $CO_2$ emissions from industry sectors with larger energy intensity since they produces goods or services retaining relatively considerable environmental load. Furthermore, it is shown that environmental load and $CO_2$ emissions in overall economy are likely increasing when the products of energy intensive industrial sector is used as inputs for less intensive sectors' production process. The result suggests we need consistent policy efforts to reduce energy intensity to lower $CO_2$ emissions.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.560-562
• /
• 2002

The liquid crystal(LC) pixel capacitance Clc, which varies as a function of applied pixel voltage, is a main factor of pixel voltage errors on input gamma voltage, and therefore of the electro-optics(E-O) characteristics of LC pixel for a-Si TFT LCDs. The pixel voltage error(${\Delta}$Vp) for input gamma voltage was simulated for 14.1 inch diagonal XGA panel. An agreement between the experimental results and simulation was satisfactory for the gamma voltage compensation, ${\Delta}$Vp of the input gamma voltage. The proposed compensation method was successfully introduced to a 14.1 inch diagonal XGA panel, and a remarkable improvement of image sticking was achived.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.639-643
• /
• 2002

The main purpose of this study was to investigate the formation mechanisms of imperfections such as irregular humps, outer cavity and inner cavity in the laser fusion zone of diamond saw blade. Laser beam welding was conducted to join two parts of blade; mild steel shank and Fe-Co-Ni sintered tip. The variables were beam power and travel speed. The microstructure and elements distributions of specimens were analyzed with SEM, AES, EPMA and so on. It was found that these imperfections were responded to heat input. Irregular humps were reduced in 10.4∼17.6kJ/m heat input range. However there were no clear evidences, which could explain the relations between humps formation and heat input. The number of outer cavity and inner cavity decreased as heat input was increased. Considering both possible defects formations mechanisms, it could be thought that outer cavity was caused by insufficient refill of keyhole, which was from rapid solidification of molten metal and fast molten metal flow to the rear keyhole wall at low heat input. More inner cavities were found near the interface of the fusion zone and sintered segment and in the bottom of the fusion zone. Inner cavity was mainly formed in the upper fusion zone at high heat input whereas was in the bottom at low heat input. Inner cavity was from trapping of coarsened preexist pores in the sintered tip and metal vapor due to rapid solidification of molten metal before the bubbles escaped.