• Journal of Animal Environmental Science
• /
• v.18 no.3
• /
• pp.257-266
• /
• 2012

Near infrared reflectance spectroscopy (NIRS) has become increasingly used as a rapid, accurate method of evaluating some chemical constituents in cereal and dired animal forages. Analysis of forage quality by NIRS usually involves dry grinding samples. Costs might be reduced if samples could be analyzed without drying or grinding. The objective of this study was to investigate effect of sample preparations on prediction ability of chemical composition and fermentation parameter for Italian ryegrass silages by NIRS. A population of 147 Italian ryegrass silages representing a wide range in chemical parameters were used in this investigation. Samples were scanned at 1nm intervals over the wavelength range 680-2500 nm and the optical data recorded as log 1/Reflectance (log 1/R) and scanned in oven-dried grinding and fresh ungrinding condition. The spectral data were regressed against a range of chemical parameters using partial least squares (PLS) multivariate analysis in conjunction with four spectral math treatments to reduced the effect of extraneous noise. The optimum calibrations were selected on the basis of minimizing the standard error of cross validation (SECV) and maximizing the correlation coefficient of cross validation (${R^2}_{CV}$). The results of this study show that NIRS predicted the chemical parameters with high degree of accuracy in oven-dried grinding treatment except for moisture contents. Prediction accuracy of the moisture contents was better for fresh ungrinding treatment (SECV 1.37%, $R^2$ 0.96) than for oven-dried grinding treatments (SECV 4.31%, $R^2$ 0.68). Although the statistical indexes for accuracy of the prediction were the lower in fresh ungrinding treatment, fresh treatment may be acceptable when processing is costly or when some changes in component due to the processing are expected. Results of this experiment showed the possibility of NIRS method to predict the chemical composition and fermentation parameter of Italian ryegrass silages as routine analysis method in feeding value evaluation and for farmer advice.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.39 no.2
• /
• pp.287-293
• /
• 2010

Regarding the physical properties of wheat flour added with lily's root powder, elasticity in farinograms tended to increase as the ratio of added lily's root powder increased. However, viscoelasticity, absorptivity, absorption time, and stability tended to decrease after an initial increase when a certain ratio of lily's root powder was added to the wheat flour. Results from the rapid viscosity analyzer (RVA) indicated that the retention strength, final viscosity, break down, set back value, $P_{max}$ value of the alveogram, and falling number value decreased. As for gaseous release, measured with a rheofermentometer, the total amount of $CO_2$ gas generated and retained tended to decrease. As for the gelatinizing properties in terms of differences in the granularity and the amount of lily's root powder (bulbs) added to wheat flour, the initial gelatinization temperature had no effect regardless of the type or amount of general grinding and minute (ultra-fine, $10\;{\mu}m$) lily's root powder. Meanwhile, the peak viscosity and peak viscosity time exhibited significant differences in 3, 5% general grinding lily's root powder additive groups. On the other hand, there was no significant difference between 3, 5% minute lily's root powder additive groups. This is likely because the activity of the enzyme in wheat flour decreased relatively and differences in the lily's root powder granularity resulted in a variation in water absorptivity. In the preference test, flavor retention of the functional bread increased according to the granularity of lily's root powder and the ratio of added lily's root powder, thus resulting in significant differences in the mouth feel and flavor; the texture and crumb color, however, did not exhibit significant differences.

• Resources Recycling
• /
• v.25 no.1
• /
• pp.3-9
• /
• 2016

The leaching behavior of gold from waste CPU chip using Iodide/Iodine solution was studied. The direct leaching of gold with Iodide/Iodine solution for CPU chip under the size of 150 mesh showed leaching ratio of 20%. It was assumed that the copper film was produced on the gold particle during grinding process and the copper film prevents lodine/Iodide solution from contacting with leachable gold. Meanwhile, the extraction of gold was improved to 90% by pretreatment process with $HNO_3$ solution. In order to explain the result, EDS and ICP analysis for the leaching residue were conducted. It was found that the copper coated on the surface of the gold particle was removed about 80% by $HNO_3$, resulting in the increment of gold leaching rate.

• The Korean Journal of Pesticide Science
• /
• v.14 no.3
• /
• pp.219-225
• /
• 2010

The solubility in water of granular pesticides is not equal because the difference of methods of producing a granular pesticide. This study was conducted to investigate fish acute toxicity of butachlor 5% GR, fipronil 0.4% GR by impregnation and carbosulfan 3% GR, diazinon 0.4% GR by coating, using carp (C. carpio), medaka (O. tatipes) and loach (M. anguillicaudatus). The test solution of each pesticide was prepared by direct addition of granular pesticide and add after grinding granular pesticide to powder in test water, We also investigated $LC_{50}$ and residual concentration until 96 hours. Test results were appeared that the treatment of powder was 1.2~4 time higher than granular and toxicity increased clearly according to elapsed time, And the residual amounts by time were detected much at early time in the powder treatment of butachlor GR and diazinon GR. Conclusively, fish acute toxicity and residual concentration in test solution appeared higher in the powder treatment than treat granular form directly in water. Also, 96 hours toxicity values were stable comparatively and the error is less than 48 hours.

• Resources Recycling
• /
• v.19 no.6
• /
• pp.51-60
• /
• 2010

A study on the recovery of cobalt and lithium from Lithium Ion Battery(LIB) scraps has been carried out by a physical treatment - leaching - solvent extraction process. The cathode scraps of LIB in production were used as a material of this experiment. The best condition for recovering cobalt from the anode scraps was acquired in each process. The cathode scraps are dissolved in 2M sulfuric acid solution with hydrogen peroxide at $95^{\circ}C$, 700 rpm. The cobalt is concentrated from the leaching solution by means of a solvent extraction circuit with bis(2-ethylhexyl) phosphoric acid(D2EHPA) and PC88A in kerosene, and then cobalt and lithium are recovered as cobalt hydroxide and lithium carbonate by precipitation technology. The purity of cobalt oxide powder was over 99.98% and the average particle size after milling was about 10 lim. The over all recoveries are over 95% for cobalt and lithium. The pilot test of mechanical separation was carried out for the recovery of cobalt from the scraps. The $Co_3O_4$ powder was made by the heat treatment of $Co(OH)_2$ and the average particle size was about 10 ${\mu}m$ after grinding. The recovery was over 99% for cobalt and lithium each other and the purity of cobalt oxide was over 99.98%.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.12 no.1
• /
• pp.82-93
• /
• 2024

Since the cement industry generates more than 60 % of CO₂ during the clinker production process, supplementary cementitious materials are used worldwide to reduce CO₂ efficiently. Mainly used supplementary cementitious materials such as blast furnace slag and fly ash, which are used in various industries including the cement industry, concrete admixtures, and ground solidification materials. However, since their availability is expected to decrease in the future according to the carbon neutrality strategy of each industry, new supplementary cementitious materials should be used to achieve the cement industry's goal for increasing the additive content of Portland cement. Limestone is a material that already has a large amount in the cement industry and has the advantage of high grinding efficiency, so overseas developed countries established Portland limestone cement standards and succeeded in commercialization. This study was an experimental study conducted to evaluate the possibility of utilizing domestic PLC, the effect of fineness and replacement ratio on the physical properties of cement was investigated, and the environmental impact of cement was evaluated by analyzing CO₂ emissions.

• Journal of Environmental Science International
• /
• v.24 no.2
• /
• pp.245-251
• /
• 2015

The main objective of this study is to recovery valuable metals with metal particle size distributions in waste cell phone PCBs(Printed Circuit Boards) by means of pulverization and nitric acid process. The particle size classifier also was evaluated by specific metal contents. The PCBs were pulverized by a fine pulverizer. The particle sizes were classified by 5 different sizes which were PcS1(0.2 mm below), PcS2(0.20~0.51 mm), PcS3(0.51~1.09 mm), PcS4(1.09~2.00 mm) and PcS5(2.00 mm above). Non-magnetic metals in the grinding particles were separated by a hand magnetic. And then, Cu, Co and Ni were separated by 3M nitric acid. Particle diameter of PCBs were 0.388~0.402 mm after the fine pulverizer. The sorting coefficient were 0.403~0.481. The highest metal content in PcS1. And the bigger particle diameter, the lower the valuable metals exist. The recovery rate of the valuable metals increases in smaller particle diameter with same leaching conditions. For further work, it could improve to recovery of the valuable metals effectively by means of individual treatment, multistage leaching and different leaching solvents.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.12
• /
• pp.978-982
• /
• 2010

For mass information transfer, the optical communication using optic fiber has been widely used. Especially, in the field of medical image, the large data is digitalized based on the standard image and it is used for telemedicine with this method. Therefore, to transfer the large amount of data fast and effectively POF (Plastic Optical Fiber) can be used and the development of optic connector for connection between POFs is very important. In this study, for stable optical coupling of POF optic fiber Ferrule and Sleeve were designed and produced by considering the bond stability and the insertion loss according to the physical contact and roughness profile was evaluated. As a result of examining the insertion loss by physical contact method of two optic fibers, it showed the loss was about 1.895dB. According to the results from studying the condition of grinding section for POF mass production, the mass production condition was established as POF profile roughness of 6nm and the loss of 0.2dB or lower by controlling the film size and time step by step.

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.1
• /
• pp.91-96
• /
• 2017

One of the most critical aspects of the modern semiconductor industry is the quality of wafer surface, the roughness of which is mostly caused by the ingot slicing. And the grinding is supposed to be the main process to reduce the surface roughness. The vibrations of the disc surface grinder are the major problem to effectively achieve the required surface quality. In this study, the structure of a disc surface grinder was analyzed through the experiment and the computer simulation to investigate the dynamic characteristics of the machine, and further to alter the design for the improved stability. The result of the study shows that simple design alterations without alternating main body can effectively suppress the vibrations of the machine.

• Resources Recycling
• /
• v.4 no.4
• /
• pp.70-75
• /
• 1995

Waste tires arc used as landifill, combustion and recycling. Rccenllg. lhc recycling of waste tires received a great attentmu fiam all industries. Thc rccgcling methods for w s l e tires are classified inla three culegoljz, a whole tirc, cmmb rubha and energy. T h ~ ssl iidy invesligvled the pruduclion ol Lhc ruhhcr block by using clumh cubbel oI wasle Ires. The process 01 manulacluring the ~uhher block was co~lsislerl ol several slepc: collecting lilts, ctuilnng and grinding hrcs, mixing crumh ruhher wlth bmder. and shaping under heat and pressure The effccl ol binder on ll~e ~uecl~ilnicaplr opcrlics o l r uhher hlock war also investigalcd. The economic feaqihility of a surface treiilmcnl and multilayas on the rubber block was dclcimincd