• Special Issue of the Society of Naval Architects of Korea
• /
• 2007.09a
• /
• pp.43-47
• /
• 2007

In this paper, we will introduce how we utilize 3D design model information at factory automation field with welding robot OLP system which is in using at out shipyard. At this area, so far, most of design information is used in NC data generation for steel cutting, but we can utilize 3D model information at more wide and complex area likes robot welding. Moreover, OpenGL which is a graphic library can be possible to verify robot NC data is correct or not through 3D simulation even if some one is not a expert at robot handling.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.23 no.5
• /
• pp.719-725
• /
• 1986

Reed-solomon(R-S) code is very effective to coerrect both random and burst errors over a noise communication channel. However, the required hardware is very complex if the B/M algorithm was employed. Moreover, when the error correction system consists of two R-S decoder and de-interleave, the I/O data bns lines becomes 9bits because of an erasure flag bit. Thus, it increases the complexity of hardware. This paper describes the R-S decoder which consisits of a error correction section that uses a direct decoding algorithm and erasure generation section and a erasure generation section which does not use the erasure flag bit. It can be shown that the proposed R-S dicoder is very effective in reducing the size of required hardware for error correction.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.737-741
• /
• 2007

This paper analyses the environmental effect of 100kw PV system installed in Tibet using Life Cycle Assessment(LCA). Then, energy payback time(EPT) and life-cycle $CO_2$ emission rate are estimated based on life-cycle of the PV system. As a result of the estimation, 6 year of EPT and 20 g-C/kWh of $CO_2$ emission rate are obtained. In China, average $CO_2$ emission rate of fossil fuel power generation plant is 260 g-C/kWh. This shows that PV system would be very promising for global environmental issues. For advanced LCA, we need to collect detailed and various data about raw material of PV system.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.5
• /
• pp.870-876
• /
• 2017

In this paper, we proposed the automatic vision inspection system using multi-layer perceptron to detect the defects occurred on rail surface. The proposed system consists of image acquisition part and analysis part. Rail surface image is acquired as equal interval using line scan camera and lighting. Mean filter and dynamic threshold is used to reduce noise and segment defect area. Various features to characterize the defects are extracted. And they are used to train and distinguish defects by MLP-classifier. The system is installed on HEMU-430X and applied to analyze the rail surface images acquired from Honam-line at high speed up to 300 km/h. Recognition rate is calculated through comparison with manual inspection results.

• New & Renewable Energy
• /
• v.3 no.2 s.10
• /
• pp.11-16
• /
• 2007

This paper analyses the environmental effect of 100kw PV system installed in Tibet using Life Cycle Assessment(LCA). Then, energy payback time(EPT) and life-cycle CO2 emission rate are estimated based on life-cycle of the PV system. As a result of the estimation, 6 year of EPT and 20 g-C/kWh of CO2 emission rate are obtained. In China, average CO2 emission rate of fossil fuel power generation plant is 260 g-C/kWh. This shows that PV system would be very promising for global environmental issues. For advanced LCA, we need to collect detailed and various data about raw material of PV system.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.190-190
• /
• 2011

In South Korea the gross generation and heated effluent of power generation plant was 259 TWh and 4.73 billion tons in 2008. And then the waste heat from power generation was 388 TWh. It shows that the efficiency of thermal power generation plant is about 40%. Therefore to reduce $CO_2$ emission from thermal power generation plant, the energy of this heated effluent must be reused to heat buildings or farm facilities. In South Korea horticultural facilities of about 25% are heated in winter season. Total area of greenhouses which are heated is about 13,000 ha. Total heat amount needed to warm greenhouse of 13,000 ha in winter season is only 3.4% of total waste heat from power generation plant. In this study a heat pump system was designed to reuse the waste heat from power generation. Especially new heat exchanger was developed to recover the thermal energy from waste water and this model considered anti-corrosion against sea water and low cost for economic feasibility. This heat recovery system was installed in mango growing greenhouse around thermal power generation plant in Seogwipo-city, Jeju Special Self-Governing Province. The result of preliminary test shows that the heating cost of about 90% is saved as compared to boiler using tax free light oil as a fuel.

• Journal of Korean Society for Quality Management
• /
• v.51 no.2
• /
• pp.315-327
• /
• 2023

Purpose: Recently, research has continued to predict the time of failure of the facility through measurement data obtained by attaching a sensor to the facility. However, depending on the facility, it may be difficult to attach a sensor. The purpose of this study is to propose a power generation maintenance plan system based on failure record data obtained from Continuous Ship Unloader, one of the facilities that is difficult to attach sensors. Methods: This study uses data collected from 2012 to 2022 from the 'CSU-1B' model among Continuous Ship Unloader operated by Korea Midland Power Co., LTD. By fitting fault record data to the Weibull distribution, appropriate maintenance cycles and ranges for each target facility subsystem are derived. In addition, maintenance group between subsystems is selected through Euclidean distance, a metric often used for time series data similarity. Through this, a system for establishing an maintenance plan for power generation facilities is proposed. Results: The results of this study are as follows. For the 17 subsystems of the Continuous Ship Unloader, proper maintenance cycles and ranges were determined, and a total of four maintenance groups were chosen. This resulted in the creation of an power generation maintenance plan system and the establishment of an maintenance plan. Conclusion: This study is a case study of power generation facilities. We proposed a maintenance plan system for Continuous Ship Unloader among power generation facilities.

• Journal of Positioning, Navigation, and Timing
• /
• v.13 no.1
• /
• pp.75-83
• /
• 2024

In order to reduce the time and cost of developing a navigation system, a performance evaluation platform can be used. A User Interface (UI) is required to effectively evaluate the performance, which sets parameters and gives navigation sensor signals and data display, and also displays navigation results. In this paper, a LabVIEW-based UI design method for multi-integrated navigation systems is proposed and implementation results are presented. The UI consists of a signal and data generation part and a signal and data processing part. The signal and data generation part sets parameters for the signal and data generation and displays the navigation sensor signal and data generation results. The signal and data processing part sets parameters for the signal and data processing and displays the navigation results. The signal and data generation part and signal and data processing part are designed to satisfy the requirements of the UI for a performance evaluation of the navigation system. In order to show the usefulness of the proposed UI design method, parameters of the signal and data generation and the signal and data processing are set through the LabVIEW-based UI, and the Global Positioning System (GPS) signal and inertial measurement unit data generation results and the navigation results of a GPS Software Defined Receiver (SDR) and inertial navigation system are confirmed. The implementation results show that the proposed UI design method helps users conduct an effective performance evaluation of navigation systems.

• Proceedings of the KIPE Conference
• /
• 2019.11a
• /
• pp.214-215
• /
• 2019

최근 신재생에너지 시스템의 보급 및 확산에 따라 자가발전시스템에 관한 연구가 활발히 이루어지고 있다. 특히 도시의 빌딩에 에너지를 효율적으로 공급 및 관리하기 위해 다양한 발전원의 하이브리드 시스템의 필요성이 대두되고 있다. 본 논문에서는 태양광(PV, Photovoltaic), 연료전지(FC, Fule Cell), 바나듐 레독스 흐름전지(VRFB, Vanadium Pedox Flow Battery)를 사용하여 도시형에 적합한 빌딩용 신재생에너지 하이브리드 발전/저장 시스템을 제안한다.

• Journal of Drive and Control
• /
• v.14 no.1
• /
• pp.23-28
• /
• 2017

A wind power heat generation system that converts wind power directly to heat instead of electric power is considered in this study. The system consists of a wind turbine part and a heat generation part. The heat generation part is materialized by a hydraulic system including a hydraulic pump, a flow control valve, a hydraulic oil tank, etc. The flow control valve primarily converts hydraulic energy generated in the pump to heat energy. It should have a function of overspeed protection under excessive wind speeds. In this study, a novel flow control valve design is proposed for excellent flow control characteristics under excessive pump driving torque (excessive wind speed). The performance of the suggested valve is analyzed using numerical simulation.