• 대한기계학회논문집
• /
• 제16권11호
• /
• pp.2082-2089
• /
• 1992

본 연구에서는 모델링재료를 이용한 AISI4130축대칭 도움형상의 열간 단조 공 정 설계 방안을 이룩하기 위한 실험을 수행하였다. 본 실험에 사용된 모델링 재료는 Van Akan International사 제품의 Plastalina를 이용하였다. 모델링재료와 실제 재 료 사이의 상사성을 검토하기 위해 압축실험을 수행하였는데 압축 실험시 모델링재료 와 평다이 사이의 마찰력을 줄이기 위해 베이비파우더, 휴지, 바셀린, 테프론테잎 등 을 이용하였으며 램 속도, 온도, 그리고 변형률도에 따른 응력 변화를 검토해 보았다. 열간 공정시에 수반되는 금형과 공작물 사이의 마찰력을 알아보기 위해 앞에 열거한 윤활제를 이용한 링실험을 수행하여 전단마찰계수(m) 값의 변화를 알아보고 폐쇄단조 시 주요한 설계방안을 검토하기 위해 플래쉬를 갖는 폐쇄단조 실험을 수행하였다. 이 실험에서는 폐쇄단조시 중요한 설계변수 중의 하나인 플래쉬 두께 대 폭비, 플래쉬 부를 통한 체적손실, 그리고 원기둥모양의 초기 단조 시편 형상비 등에 따른 설계방안 을 검토하여 기존 참고문헌에 나와 있는 결과들과 유사성을 검토하였다. 이와같은 실험 결과를 체계적으로 확립하고 고강도강 대형 단조품생산에 필요한 단조하중 예측, 예비성형체 설계, 성형성 연구등에 대한 응용성을 검토하고자 한다.

• 대한기계학회논문집A
• /
• 제34권4호
• /
• pp.423-430
• /
• 2010

표면의 균열, 겹침결함, 금형의 코너반경이 작아 재료의 유동성이 낮을 때 발생하는 콜드셧, 부분충진등의 단조결함이 없는 자동차용 단조 플랜지를 생산하기 위해서 열전달, 단류선 흐름, 응력분포를 고려하여 형단조 공정과 금형에 대한 해석을 수행하였다. 축박기(up-set) 단조, 예비성형, 최종성형, 단조압력으로 구성된 단조과정은 유한요소법으로 해석되었다. 예비성형과 상하 금형의 높이비율이 단조공정과 금형에 미치는 영향을 평가하여 예비금형의 각 $10^{\circ}$와 최종 금형의 상하비율 1.5:1이 단조결함이 없는 결과를 나타내었다. 이를 반영한 새로 설계된 금형은 재료강도, 완전충진, 하중한계 13,000 KN 이라는 공정변수를 모두 만족시켰다. 이론 입증을 위해서 개선된 금형과 플랜지가 제작되었으며, 단조결함이 발견되지 않았다.

• 소성∙가공
• /
• 제14권5호
• /
• pp.460-465
• /
• 2005

The temperature difference between die and workpiece has been frequently caused to various surface defects. The distribution and change for the temperature of forged part should be analyzed to prevent the generation of various defects related with the temperature. The surface temperature changes were affected with the interface heat transfer coefficient. Therefore, the coefficient is necessary to predict the temperature changes of die and workpiece. In this study, the experimental and FE analysis were performed to evaluate the coefficient with a function of pressure, temperature, material, and etc. The closed die upsetting was used to measure the coefficient on pressure over the flow stress. AISI1045, A16061, and Cu-OFHC were used to analyze the effect of material. The coefficient was increased with step-up of pressure between die and workpiece. And, A16061 was larger than that of the AISI1045 and Cu-OFHC up to the five times.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 추계학술대회 논문집
• /
• pp.178-184
• /
• 2000

To obtain high quality component with thixoforming process, it is important that the homegeneous distribution of solid particles without liquid segregation. In closed-die semi-solid forging process, liquid segregation is strongly affected by injection velocity than any other process variables because the material has to travel relatively long distance to fill the cavity through a narrow gate before solidification begins. The optimal injection velocity and die temperature were investigated to fabricate near-net-shape compressor component called Al frame.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1994년도 춘계학술대회 논문집
• /
• pp.209-217
• /
• 1994

The present study is concerned with the characteristics of the high speed precision bar cropping. This process is a practical application of High Energy Rate Forming in which the impact energy source is given by internal combustion engine. To enhance the added value of product, the recent forging fields trend toward the near net shape processes through the cold and closed die forging. For the purpose of these processes the precedent process is to obtain the precision billet which has little weight deviation and defect. The accuracy of initial billet by bar cropping depends upon the process parameters and die design technology. Therefore, in order to investigate the effect of process parameters upon product quality, the cropping experiments are carried out according to the various parameters such as billet clearence, billet length, billet material, cropping speed and so on. From these results some criteria of the optimal die design for the product of good quality are suggested.

• 한국산학기술학회논문지
• /
• 제4권1호
• /
• pp.36-41
• /
• 2003

열간단조 밀폐금형의 수명연장을 위한 빌릿의 소성변형 유동해석을 유한 요소법에 의하여 실시한 결과 임프레션 형상에 대한 수정설계를 수행하였고, 임프레션 표면 마멸부위의 보수방법을 육성용접에 의한 방법으로 금형을 재생하여 사용한 결과 개발 전의 3,0(H개 생산에서 개발 후 5,000개 양산되었을 때 임프레션 표면을 관찰하였더니 3,000개 정도에서 나타났던 마멸보다 얕은 마멸이 나타났다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 춘계학술대회 논문집
• /
• pp.57-60
• /
• 2008

The studies for internal void closure have been conducted experimentally and numerically for open die forging. The FEM analysis is performed to investigate the deformation behavior of some internal voids in cast ingots during two upsetting stages. The calculated results of void closure behavior are compared with the measured results before and after upsetting. The shapes and sizes of each internal void are scanned by the X-ray scanner. From this result, the criteria for deformation amounts effect on the void closure can be investigated by the types of void. Closed voids could be compressed and eliminated after forging when the applied deformation amounts were larger than the critical effective strains. On the other hand, open voids could not be compressed and removed.

• 소성∙가공
• /
• 제17권8호
• /
• pp.600-606
• /
• 2008

In closed-die hot forging, a billet is formed in dies such that the flow of metal from the die cavity is restricted. Some parts can be forged in a single set of dies, whilst others, due to shape complexity and material flow limitations, must be shaped in multi sets of dies. The purpose of a performing operation is to distribute the volume of the parts such that material flow in the finisher dies will be sound. This study focused on the design of preforms, flash thickness and land width by theoretical calculation and finite element analysis, to manufacture the super hot forging product, 70MC type piston crown used in marine engine. The optimal design of preforms by the finite element analysis and the design experiment achieves adequate metal distribution without any defects and guarantees the minimum forming load and fully filling of the cavity of the die for producing the large piston crown. The maximum loads obtained by finite element analysis are compared with the results of experiments. The loads of the analysis have good agreements with those of the experiment. Results obtained using DEFORM-2D enable the designer and manufacturer of super hot forging dies to be more efficient in this field.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.219-222
• /
• 2005

The temperature difference between die and workpiece has frequently caused various surface defects. The non-homogeneous temperature distribution of forged part should be analyzed to prevent the generation of various defects related with the temperature. The surface temperatures were mainly affected by the coefficient of thermal contact conductance. The precise coefficient is necessary to predict accurately the temperature changes of die and workpiece. The experiment is preformed to measure the temperature distribution of die and workpiece in closed die upsetting. And then, the coefficient is classified into function of pressure and confirmed by the comparison between experiments and FE analyses using the other model. The FE analysis to predict the temperature distribution is performed by commercial software $DEFORM-3D^{TM}$. However, it might be impossible to measure directly the temperature distribution of forged part. Therefore, the comparisons between measured temperature and predicted values are performed with the hardness of Al6061-forged part.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.84-88
• /
• 2009

The nickel-based alloy Nimonic 80A possesses strength, and corrosion, creep and oxidation resistance at high temperature. The exhaust valves of low speed diesel engines are usually operated at temperature levels of 400-$600^{\circ}C$ and high pressure to enhance thermal efficiency and exposed to the corrosion atmosphere by the exhaust gas. Also, the exhaust valve is subjected to repeated thermal and mechanical loads. So, the nickel-based alloy Nimonic 80A was used for the large exhaust valve spindle. It is composed a 540mm diameter head and a 125mm diameter stem. It is developed large products by hot closed-die forging. Manufacturing process analysis of the large exhaust valve spindle was simulated by closed die forging with hydraulic press and cooled in air after forging. The preform was heated to $1080^{\circ}C$ Numerical calculation was performed by DEFORM-2D, a commercial finite element code. Heat transfer can be coupled with the deformation analysis in a non-isothermal deformation analysis. Mechanical properties of the large exhaust valve spindle were evaluated by the variety of tests, including microstructure observation, tensile, as well as hardness and fatigue tests, were conducted to evaluate the mechanical properties for head part of exhaust valve spindle.