• Journal of Welding and Joining
• /
• v.23 no.3
• /
• pp.76-82
• /
• 2005

Recently the application of laser welding technology has been considered to shipbuilding structure. However, when this technology is applied to primer coated steel, good quality weld beads are not easily obtained. Because the primer-coated layer caused the spatter, humping bead and porosity which are main part of the welding defect attributed to the powerful vaporizing pressure of zinc. So we performed experiment with objectives of understanding spatter and porosity formation mechanism and producing sound weld beads in 6mmt primer coated steels by a $CO_2$ CW laser. The effects of welding parameters; defocused distance, welding speed, coated thickness and coated position; were investigated in the bead shape and penetration depth on bead and lap welding. Alternative idea was suggested to suspend the welding defect by giving a reasonable gap clearance for primer coated thickness. The zinc of primer has a boiling point that is lower than melting point of steel. Zinc vapor builds up at the interface between the two sheets and this tends to deteriorate the quality of the weld by ejecting weld material from lap position or leaving porosity. Significant effects of primer coated position was lap side rather than surface. Therefore introducing a small gap clearance in the lap position, the zinc vapor could escape through it and sound weld beads can be acquired. In conclusion, formation and suspension mechanism of the welding defects was suggested by controling the factors.

• Proceedings of KOSOMES biannual meeting
• /
• 2018.06a
• /
• pp.53-53
• /
• 2018

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1996.05a
• /
• pp.17-23
• /
• 1996

Gerotor Pump and Motors are widely used in lubrication and hydraulic actuator systems, These have many advantage compared with internal gear pump and motors, But the gerotor profile have not been sufficiently analyzed theoretically. So it is vary difficult for designer to decide the specifications of the gerotor profile, and it is not yet confirmed to calculating flow rate and minimum distance of clearance in the contact point of inner and outer rotor. In this paper, When we design inner and outer rotor concurently, We have analyzed the gerotor and displayed the calculated results such as flow rate, minumum distance between inner and outer rotor and gerotor profiles

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.1 no.2
• /
• pp.182-189
• /
• 1989

The propose of this study is augmentation of heat transfer without additional external power in 2-dimensional impinging air jet. The passive heat transfer augmentation method tried in this experimental study is placement of rod bundles with the clearance, 2mm, in front of the heat transfer surface. The effects of pitch distance among rods and nozzle-to-target plate distance are investigated. The overall heat transfer rate of flat plate with rods reaches maximum at H/B=10 and P=40mm, and for H/B=2 and P=40mm the augmentation rate of heat transfer becomes maximum to a value which is about 1.57 times that of the flat plate without rods.

• Tribology and Lubricants
• /
• v.31 no.5
• /
• pp.213-220
• /
• 2015

This study evaluates the effect of grooves on the stem part of a plunger on the lubrication characteristics of a fuel injection pump (FIP) by using hydrodynamic lubrication analysis. The current study uses the two-dimensional Reynolds equation to evaluate the changes in lubrication characteristics with variations in clearance, viscosity, and grooves for a laminar, incompressible, and unsteady state flow. This study investigates the lubrication characteristics by comparing the dimensionless minimum film thickness or the film parameter, which is the ratio of the minimum film thickness to surface roughness. The analysis method for the groove section differs depending on the depth of the groove. For instance, in the case of a shallow groove, the film thickness equation considers the depth of the groove, while in the case of a deep grove, it considers the flow continuity. The lubrication characteristics of the FIP are more sensitive to changes in the groove width than to changes in other design variables. Moreover, the application of a groove is more effective under low viscosity conditions. The smaller the distance from the edge of the stem part to the first groove in the case of shallow grooves, the better are the lubrication characteristics of the FIP. In contrast, in the case of deep grooves, the lubrication characteristics of the FIP improve as the distance increases. The application of shallow grooves is more effective for improving the lubrication characteristics than the application of deep grooves.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.17 no.4
• /
• pp.3970-3979
• /
• 1975

On account of the development of the high speed internal combustion engines, several methods for increasing burning velocity has been investigated lately. Installation of a squash area on a cylinder head is one of the simple and practical method to induce the strong tubulant flow of air-fuel mixtureinto a combustion chamber. In this study, a four-stroke engine used for agricultural purpose was tested as an experimental model. A mathematical model of the squash velocity was derived, and also, several characteristics of the squash phenomena during the motoring of the engine used as a modelwere investigated. The results obtained were as follows: (1) Mathematical model of squash velocity was established and cheked (2) Squaash velocity and engine speed were found to be proportional to the squash area while they were inversely proportional to the squash width. (3) Squash velocity and crank angle at which the squash velocity become its peak were influenced by the magnitude of squash clearance: increase of squash clearance made squash velocity reduced acd made the peak of the squash velocity for from the top dead center and (4) When the squash area is divided in small areas baving unit width along the squash section, squash velocity at each unit width was proportional to the magnitude of the squash distance covered by the unit width.

• Journal of Korean Neurosurgical Society
• /
• v.66 no.4
• /
• pp.476-481
• /
• 2023

Objective : The latest version of the Leksell Gamma Knife Icon^TM allows for mask- and frame-based fixation. Although mask fixation provides fractionated treatment and immobilization using a noninvasive method, it is not free from collision. The authors investigated the collision problem with a modified mask fixation method. Methods : This study presents a case of two meningiomas in the frontal area, where a collision occurs in the occipital area. A modified mask fixation method was introduced to avoid the collision : first, the edges of the head cushion were cut off and polystyrene beads with a diameter of approximately 5 cm were removed. Next, the head cushion was sealed using a stapler. Finally, the head cushion was flattened in the adapter. We compared the shot coordinates, 3-dimensional (3D) error, clearance distance, and vertical depth of the head cushion between the initial and modified mask fixations. Results : When comparing the initial and modified mask fixations, the difference in the shot coordinates was +10.5 mm along the y-axis, the difference in the 3D error was approximately 18 mm, and the difference in clearance was -10.2 mm. The head cushion was approximately 8 mm deeper in the modified mask fixation. Conclusion : Based on these findings, we recommend a modified mask fixation method for gamma knife radiosurgery using ICON with a collision.

• Spatial Information Research
• /
• v.15 no.4
• /
• pp.363-370
• /
• 2007

This study has been carried for the development of the basic algorithm of helicopter navigation system based on TRN (Terrain Referenced Navigation) with information input from the GPS. The helicopter determines flight path due to Origination-Destination analysis on the Cartesian coordinate system of 3-D DTM. This system shows 3-D mesh map and the O-D flight path profile for the pilot's acknowledgement of the terrain, at first. The system builds TCF (terrain clearance floor) far the buffer zone upon the surface of ground relief to avid the ground collision. If the helicopter enters to the buffer zone during navigation, the real-time warning message which commands to raise the body pops up using Matlab menu. While departing or landing, control of the height of the body is possible. At present, the information (x, y, z coordinates) from the GPS is assumed to be input into the system every 92.8 m of horizontal distance while navigating along flight path. DTM of 3" interval has been adopted from that which was provided by ChumSungDae Co., Ltd..

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.3
• /
• pp.311-318
• /
• 2018

In accordance with the stipulations of the STCW Convention, simulation training has been enforced in order to develop practical skills so as to prevent accidents by predetermining the risks in special marine environments. Simulation training is a useful way to acquire navigation abilities, and can continuously measure the ability of a trainee by applying an appropriate evaluation. However, the result of training is evaluated by the instructor's subjective judgment without quantitative criteria. Therefore, this study aims to quantitatively evaluate the effectiveness of simulation training. For this purpose, evaluation items were derived by analyzing legal standards, earlier studies, and the current status of MET institutions. The simulations were then performed three times in the same scenarios and analyzed the results. As a result, it has been shown that the objectively analyzed ability to keep the route and to make safe passage with other vessel, as well as subjectively evaluated ability by the apprentice officer has been improved as training progressed. Through the evaluation of simulation training results, it can be derived that simulation education needs supplementation, and can be provided as a basic form of data to quantify the evaluation results of the simulation training in the future.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.8
• /
• pp.3650-3655
• /
• 2013

A state purpose to produce fine blanking die gets to be the maximum size of share surface the study considered that change a size of share area. the clearance affecting most greatly size of share surface fixing as 1% of material thickness and while change share speed, A distance change from share line to V-ring center, A change of V-ring angle. it designed. Each test specimen taken from the share surface size analysis of the V-ring distance of 2mm, the outer $45^{\circ}$ / inner$30^{\circ}$ if the, Shear speed was found that the area of the entire cross section is largest the 6.4m/min.