• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.11a
• /
• pp.54-58
• /
• 1994

H$_2$ bake and GeH$_4$ clean are used as a in-situ pre-clean method in low temperature Si based epitaxial growth technology using rapid thermal processing chemical vapor deposition (RTPCVD). In this paper, the H$_2$ bake and GeH$_4$ clean processes are optimized for low surface defect density using Taguchi method. In H$_2$ bake process, the epitaxial growth temperature affects dominantly on the surface defect density, and the next affecting factors are H$_2$ bake temperature and rinse time in de-ionised water. In GeH$_4$ clean process, GeH$_4$ clean temperature affects most strongly on the surface defect density, and the minor factor is GeH$_4$flow rate. The optimum process conditions predicted fly Taguchi method agree well with tile experimental data in both in-situ clean processes.

• Clean Technology
• /
• v.24 no.2
• /
• pp.119-126
• /
• 2018

This study introduced a treatment process that was developed to treat Indonesian low-rank coal with high-ash content, which has the same characteristics as residual coal from the biosolubilization process. The treatment process includes separation of ash, solid-liquid separation, pelletizing, and drying. To reduce the ash content, flotation was performed using 4-methyl-2-pentanol (MIBC) as frother, and kerosene, waste oil, and cashew nut shell liquid (CNSL) as collectors. The increasing amount of collector had an effect on combustible coal recovery and ash reduction. After flotation, a filter press, extruder, and an oven drier were used to make a dried coal pellet. Then another coal pellet was made using asphalt as a binder. The compressive strength and friability of the coal pellets were tested and compared.

• Journal of Biosystems Engineering
• /
• v.24 no.4
• /
• pp.317-324
• /
• 1999

This study was conducted to decide several design criterion for clean-washed rice processing system development. A Computer simulation was used to predict and analyze the mass balances and moisture changes of the process of clean-washed rice processing system. The following results were obtained from this study. 1. In order to attain the processing capacity of 1,000kg/h of the clean-washed rice processing system, that of the system was designed as 1,400kg/h which was based on the safety factor of 40% and handling capability of mass variations occurred during processing. 2. It was analyzed that the proper time required for aqueous cleaning process should be within one minute. 2. It was analyzed that the proper time required for aqueous cleaning process should be within one minute. 3. The final moisture content of clean-washed rice was controlled being 15%(w.b.) for the sake of safe storage. 4. It was proven that the optimum drying time was three minutes for the clean-washed rice dried by a rotary dryer.

• Clean Technology
• /
• v.3 no.2
• /
• pp.31-33
• /
• 1997

Nitrate contamination in surface water and ground water have increased in Korea. This trend has raised concern because nitrates caused methemoglobinemia in infants. To remove nitrates from waters, various purification processes including ion-exchange, biological denitrification, and chemical denitrification are currently in use for the treatment of water. However, little economically advantageous process exists for the industrial scale treatment of effluents highly polluted with nitrates. A new process has been developed for nitrate and other salts removal from polluted waters. Alumina cement and lime served as precipitating agents to remove nitrate with stirring at basic pH. Decreasing alumina content in alumina cement result in a increasing in nitrate removal yield. Stable removal of nitrate(1000mg/L) was readily achieved by two-stage removal process.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1999.12a
• /
• pp.371-377
• /
• 1999

• Clean Technology
• /
• v.3 no.2
• /
• pp.25-27
• /
• 1997

• Korean Journal of Organic Agriculture
• /
• v.23 no.4
• /
• pp.643-658
• /
• 2015

This study presents detailed emission of greenhouse gases of using Clean Energy Agriculture System according to a cradle-to-gate life-cycle assessment, including emission from energy use and leak of Biogas. Calculations were done with the PASS software and the covered gases are $CH_4$, $N_2O$ and $CO_2$, Total GHG fluxes of amount to $1719.03kgCO_2/day$, $39.63kgCO_2/day$ (2.31%) are from facility house process, $0.19kgCO_2/day$ (0.01%) are from transport process, $696.72kgCO_2/day$ (40.53%) are from Anaerobic digestion process, $846.61kgCO_2/day$ (49.25%) are from Heating and cooling system, $135.88kgCO_2/day$ (7.90%) are from Fertigation production process. The results suggest that for effective reduction of GHG emissions from Facility house using clean energy. Reduction targets should address both the production process as defined by IPCC sectors and the consumption process. An LCA assessment as presented here could be a basis for such efforts.

• Electronic Materials Letters
• /
• v.14 no.6
• /
• pp.718-724
• /
• 2018

With the development of photovoltaic industry, the cost of photovoltaic power generation has become the significant issue. And the metallization process has decided the cost of original materials and photovoltaic efficiency of the solar cells. Nowadays, double printing process has been introduced instead of one-step printing process for front contact of polycrystalline silicon solar cells, which can effectively improve the photovoltaic conversion efficiency of silicon solar cells. Here, the relative cheap Cu paste has replaced the expensive Ag paste to form Ag/Cu composite front contact of silicon solar cells. The photovoltaic performance and the cost of photovoltaic power generation have been investigated. With the optimization on structure and height of Cu finger layer for Ag/Cu composite double-printed front contact, the silicon solar cells have exhibited a photovoltaic conversion efficiency of 18.41%, which has reduced 3.42 cent per Watt for the cost of photovoltaic power generation.

• Clean Technology
• /
• v.2 no.2
• /
• pp.165-175
• /
• 1996

Cutting fluids in machining process are one of the parameters which have serious effects on the environment. A simple method to accomplish the environmentally clean process is to evaluate the effects of cutting fluids and select one which has the least environmental load. In this research, a process planning to select the best cutting fluid is suggested considering both machinability and environmental effects. The selection criteria and evaluation method named AHP are introduced. The planning process is illustrated with drilling characterized as a heavy-duty and low-speed process. Five standard fluids are compared with respect to five environmental attributes. Compounded cutting oils are superior to water-soluble oils in both machinability and environmental effects.

• Clean Technology
• /
• v.5 no.1
• /
• pp.1-15
• /
• 1999