• Steel and Composite Structures
• /
• 제31권3호
• /
• pp.233-242
• /
• 2019

Early detection of damage bonding state such as insufficient bonding strength and interface partial contact defect for the explosive clad pipe is crucial in order to avoid sudden failure and even catastrophic accidents. A generalized and efficient model of the explosive clad pipe can reveal the relationship between bonding state and vibration characteristics, and provide foundations and priory knowledge for bonding state detection by signal processing technique. In this paper, the slender explosive clad pipe is regarded as two parallel elastic beams continuously joined by an elastic layer, and the elastic layer is capable to describe the non-uniform bonding state. By taking the characteristic beam modal functions as the admissible functions, the Rayleigh-Ritz method is employed to derive the dynamic model which enables one to consider inhomogeneous system and any boundary conditions. Then, the proposed model is validated by both numerical results and experiment. Parametric studies are carried out to investigate the effects of bonding strength and the length of partial contact defect on the natural frequency and forced response of the explosive clad pipe. A potential method for identifying the bonding quality of the explosive clad pipe is also discussed in this paper.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 춘계학술대회 논문집 전기설비전문위원
• /
• pp.58-60
• /
• 2007

This paper introduces the IN-FLEX system using aluminum clad flex cable, which is expected to alternate the conventional wiring method, such as, a steel pipe wiring method, and a synthetic resin pipe wiring method. The aluminum clad flex cable has a superior operation characteristics in heat dissipation property, in installation and maintenance facility, flammability, and appearance. Moreover, the IN-FLEX system adopted an easy connection mechanism which enable to reduce the time, hands and expense for the installation and maintenance of the system. Certification tests verifying the superior operation characteristics and reliability of the system using aluminum clad flex cable were carried with standard method in KOLAS certification institute.

• Journal of Welding and Joining
• /
• 제31권6호
• /
• pp.90-95
• /
• 2013

Pipe inside clad welding is mainly used to the flow pipe of sub-sea or chemical plant. For the inside clad welding to the medium pipe with the diameter of about 12", TIG welding is frequently applied with filler metal. In this case, the clad welding has the very broad weld area over $10m^2$. And, the non-destructive test (NDT) such as ultrasonic test (UT) or radiographic testing (RT) should be conducted on the broad weld area, and it costs very high due to the time-consuming work. Therefore, the present study investigated the variation of arc voltage to develop the in-line quality monitoring system for the pipe inside TIG cladding. The 4 experimental parameters (current, arc length, wire feed position, and shield gas flow rate) varied to observe the change of arc voltage and to establish the model for the monitoring. The arc voltage was decreased when the wire was fed to the backward eccentric position(over 2mm), and the shield gas flow rate was insufficient under 10L/min. In the case of the backward eccentric position over 2mm, the bead appearance was not good and the dilution ratio was increased due to deep penetration. When the shield gas flow rate was lower than 10L/min, the bead surface was oxidized.

• 한국산학기술학회논문지
• /
• 제17권11호
• /
• pp.42-50
• /
• 2016

오버레이 용접은 희석율에 의해 적층 두께에 따라 화학성분 함량과 용접부의 경도에 영향을 미치며 이는 파이프 제품의 표면성질을 결정한다. 이로 인해 오버레이 용접은 적층의 수를 고려하여야 한다. 본 연구에서는 탄소강 모재에 내부식성 소재인 모넬 소재를 오버레이 용접하여 적층수에 따른 Fe함량, 모재와 모넬 소재와의 용접성, 부위별 경도와 표면 평탄도를 실험적으로 연구하였다. 각각의 평가는 평판의 모재와 파이프 모재에 3개의 층으로 오버레이 용접 후 실시하였다. Fe함량은 각 층별 시료를 채취하여 성분 분석을 통해 평가하였으며, 3Layer에서 만족하는 함량을 나타내었다. 또한 적층별 시편을 밴딩 시험하여 용접성을 평가하였다. 적층별 경도와 비드 평탄도는 Micro Vickers와 3차원 측정을 통해 평가하였다. 경도는 1Layer에서 발생하는 HAZ부에 의해 가장 높은 경도 값을 보였으며, 적층이 증가할수록 경도가 감소하였다. 비드 평탄도의 경우 적층수 증가에 따라 편차가 급격한 차이가 발생하였으며, 이는 경도와 함께 사용 목적의 측면에서 주의 깊게 고려해야 한다. 이러한 실험적 결과는 목적에 따른 용접 파이프 적층수의 결정 방법을 나타내었다.

• Nuclear Engineering and Technology
• /
• 제53권4호
• /
• pp.1100-1108
• /
• 2021

Supercritical water has great potential as a coolant for nuclear reactor. Its use will lead to higher thermal efficiency of Rankine cycle. However, in certain conditions heat transfer may get deteriorated which may lead to undesirable high clad surface temperature. It is necessary to estimate the operating conditions in which heat transfer deterioration (HTD) will take place, so as to establish thermal margins for safe reactor operation. In the present work, the heat flux corresponding to onset of HTD for vertically upward flow of supercritical water in a pipe is obtained over a wide range of system parameters, namely pressure, mass flux, and pipe diameter. This is done by performing large number of simulations using an in-house CFD code, which is especially developed and validated for this purpose. The identification of HTD is based on observance of one or more peak/s in the computed wall temperature profile. The existing correlations for predicting the onset of HTD are compared against the results obtained by present simulations as well as available sets of experimental data. It is found that the prediction accuracy of the correlation proposed by Dongliang et al. is best among the existing correlations.