• International Journal of Aerospace System Engineering
• /
• 제9권2호
• /
• pp.1-9
• /
• 2022

The NEA release mechanism is used to provide restraint and release functions with low shock for critical deployment operations on solar arrays after launch. The GK3 solar array consists of 2 wings and 6 hold down points per panel. The NEA SSD9103S1 is a part of the GK3 solar array hold-down and release mechanism. Each NEA unit is equipped with two Z-diodes which provide power to a NEA unit connected in series after actuation of the fuse wire. This paper presents the hot firing test results of a quadrature NEA SSD9103S1 configuration. One output powers a maximum of 4 NEA SSD9103S1 units simultaneously. The necessary actuation pulse duration has been determined to meet margin requirement for thermal energy of minimum 4. Actuation thermal energy difference is about 6.6% between each half of two fired serial NEAs. Thermal energy margin at worst case is minimum 5.9 in case of an actuation pulse duration of 500 ms. Two series Zener impedance depend on current applied has been characterized by an additional actuation after all fuse wires are open circuit. Total number of actuation commands to the GK3 NEA unit reduce drastically from 24 in case of single NEA configuration down to 8 in case of parallel and quadrature NEA configurations. It can be accommodated by the existing HP2U Pyro design without any impact.

• 전기전자학회논문지
• /
• 제26권4호
• /
• pp.722-727
• /
• 2022

본 논문에서는 0.25 ㎛의 게이트를 갖는 AlGaN/GaN HEMT를 기반으로 개발된 X-대역 전력 증폭기 MMIC의 특성을 기술한다. 개발된 X-대역 전력 증폭기 MMIC는 9 GHz~10 GHz의 주파수 대역에서 21.6 dB 이상의 소신호 이득과 46.11dBm(40.83 W) 이상의 출력 전력을 가진다. 전력 부가 효율 특성은 43.09%~44.47%이며 칩의 크기는 3.6 mm×4.3 mm이다. 출력 전력 밀도는 2.69 W/mm²를 나타내었다. 개발된 AlGaN/GaN 전력 증폭기 MMIC는 다양한 X-대역 레이더 응용에 적용 가능하다.

• 한국인터넷방송통신학회논문지
• /
• 제22권4호
• /
• pp.67-72
• /
• 2022

본 논문에서는 60 nm GaN/Si HEMT 공정을 사용하여 전력증폭기(Power Amplifier)의 설계를 제시하였다. 고주파 설계를 위하여 맞춤형 트랜지스터 모델을 구성하였다. Output stage는 저손실 설계를 위해 마이크로스트립 라인을 사용하여 회로를 구성하였다. 또한 RC 네트워크로 구성된 Bias Feeding Line과 Input bypass 회로의 AC Ground(ACGND) 회로를 각각 적용하여 DC 소스에 연결된 노드의 최소임피던스가 RF회로에 영향을 미치지 않도록 하였다. 이득과 출력을 고려하여 3단의 구조로 설계되었다. 설계된 전력증폭기의 최종 사이즈는 3900 ㎛ × 2300 ㎛ 이다. 중심 주파수에서 설계된 결과는 12 V의 공급 전압에서 15.9 dB의 소 신호 이득, 29.9 dBm의 포화 출력(Psat), 24.2 %의 PAE를 달성하였다.

• 한국정보기술학회 영문논문지
• /
• 제10권1호
• /
• pp.71-83
• /
• 2020

In this paper, we propose a system that can detect the shape of a hand at high speed using an FPGA. The hand-shape detection system is designed using Verilog HDL, a hardware language that can process in parallel instead of sequentially running C++ because real-time processing is important. There are several methods for hand gesture recognition, but the image processing method is used. Since the human eye is sensitive to brightness, the YCbCr color model was selected among various color expression methods to obtain a result that is less affected by lighting. For the CbCr elements, only the components corresponding to the skin color are filtered out from the input image by utilizing the restriction conditions. In order to increase the speed of object recognition, a median filter that removes noise present in the input image is used, and this filter is designed to allow comparison of values and extraction of intermediate values at the same time to reduce the amount of computation. For parallel processing, it is designed to locate the centerline of the hand during scanning and sorting the stored data. The line with the highest count is selected as the center line of the hand, and the size of the hand is determined based on the count, and the hand and arm parts are separated. The designed hardware circuit satisfied the target operating frequency and the number of gates.

• Advances in Computational Design
• /
• 제7권1호
• /
• pp.57-68
• /
• 2022

A simulation study of the distribution of magnetic flux induced by a U-shaped electromagnet into a two-layer massive object with variations in the depth and properties of the surface layer has been carried out. It has been established that the hardened surface layer "pushes" the magnetic flux into the bulk of the magnetized object and the magnetic flux penetration depth monotonically increases with increasing thickness of the hardened layer. A change in the thickness and magnetic properties of the surface layer leads to a redistribution of magnetic fluxes passing between the poles of the electromagnet along with the layer and the bulk of the steel object. In this case, the change in the layer thickness significantly affects the magnitude of the tangential component of the field on the surface of the object in the interpolar space, and the change in the properties of the layer affects the magnitude of the magnetic flux in the magnetic "transducer-object" circuit. This difference in magnetic parameters can be used for selective testing of the surface hardening quality. It has been shown that the hardened layer pushes the magnetic flux into the depth of the magnetized object. The nominal depth of penetration of the flow monotonically increases with an increase in the thickness of the hardened layer.

• Design & Manufacturing
• /
• 제16권4호
• /
• pp.52-59
• /
• 2022

Currently, Korea is an aging society and is expected to become a super-aged society in about four years. X-ray devices are widely used for early diagnosis in hospitals, and many X-ray technologies are being developed. The development of X-ray device technology is important, but it is also important to increase the reliability of the device through accurate data management. Sensor nodes such as temperature, voltage, and current of the diagnosis device may malfunction or transmit inaccurate data due to various causes such as failure or power outage. Therefore, in this study, the temperature, tube voltage, and tube current data related to each sensor and detection circuit of the diagnostic X-ray imaging device were measured and analyzed. Based on QC data, device failure prediction and diagnosis algorithms were designed and performed. The fault diagnosis algorithm can configure a simulator capable of setting user parameter values, displaying sensor output graphs, and displaying signs of sensor abnormalities, and can check the detection results when each sensor is operating normally and when the sensor is abnormal. It is judged that efficient device management and diagnosis is possible because it monitors abnormal data values (temperature, voltage, current) in real time and automatically diagnoses failures by feeding back the abnormal values detected at each stage. Although this algorithm cannot predict all failures related to temperature, voltage, and current of diagnostic X-ray imaging devices, it can detect temperature rise, bouncing values, device physical limits, input/output values, and radiation-related anomalies. exposure. If a value exceeding the maximum variation value of each data occurs, it is judged that it will be possible to check and respond in preparation for device failure. If a device's sensor fails, unexpected accidents may occur, increasing costs and risks, and regular maintenance cannot cope with all errors or failures. Therefore, since real-time maintenance through continuous data monitoring is possible, reliability improvement, maintenance cost reduction, and efficient management of equipment are expected to be possible.

• 한국전자통신학회논문지
• /
• 제18권4호
• /
• pp.571-578
• /
• 2023

본 논문에서는 차내 통신을 위한 데이터 송신기에 지연고정루프를 접목한 회로를 제안한다. 낮은 전자기 간섭 특성을 가진 송신기의 설계를 위해 낮은 슬루율을 가지며, 회로 소자의 공정에 따른 변화로 인한 슬루율 변화량을 보정할 수 있는 지연고정루프를 적용하였다. 시뮬레이션 결과에 의하면, 지연고정루프가 적용된 송신기는 기존의 송신기보다 낮은 슬루율 변화량을 가진다. 제안한 구조의 회로는 65nm 공정으로 설계되었으며, 데이터 전송속도는 20Mbps, 공급전압은 1.1V이다. 지연고정루프가 있는 송신기는 기존의 송신기에 대비하여 빠른 조건에서 53.6% 낮은 슬루율 변화량, 느린 조건에서 13.07% 낮은 슬루율 변화량을 가진다.

• Composites Research
• /
• 제19권1호
• /
• pp.15-21
• /
• 2006

일방향 섬유로 보강된 고성능 복합재료의 경우 모든 방향에서 곡률을 가지는 구조물의 제작에 용이하지 않다. 본 연구에서는 높은 비강성, 비강도를 가지는 일방향으로 보강된 AS4/PEEK 프리프레그 테이프를 이용한 축소 시제 복합재료 접시형 안테나 반사판의 개발 결과를 보여준다. 개발을 위해서 유한요소법을 통한 적층인자 연구를 통한 저열팽창/등방변형의 반사판 설계기법을 확립하였으며, Fiber Placement System을 통한 자동섬유적층법을 이용하여 접시형 안테나 반사판이 제작되었다. 제작된 반사판은 Full Bridge Circuit의 Strain Cage를 이용한 열변형 실험법으로 열팽창 거동에 대한 실험을 수행하였으며, 열변형 해석결과와의 비교를 통하여 제작된 구조물을 검증하였다.

• 농업과학연구
• /
• 제48권4호
• /
• pp.703-718
• /
• 2021

An irrigation monitoring system is an efficient approach to save water and to provide effective irrigation scheduling for rice cultivation in desert soils. This research aimed to design, fabricate, and evaluate the basic performance of an irrigation monitoring system based on information and communication technology (ICT) for rice cultivation under drip and micro-sprinkler irrigation in desert soils using a Raspberry Pi. A data acquisition system was installed and tested inside a rice cultivating net house at the United Arab Emirates University, Al-Foah, Al-Ain. The Raspberry Pi operating system was used to control the irrigation and to monitor the soil water content, ambient temperature, humidity, and light intensity inside the net house. Soil water content sensors were placed in the desert soil at depths of 10, 20, 30, 40, and 50 cm. A sensor-based automatic irrigation logic circuit was used to control the actuators and to manage the crop irrigation operations depending on the soil water content requirements. A developed webserver was used to store the sensor data and update the actuator status by communicating via the Pi-embedded Wi-Fi network. The maximum and minimum average soil water contents, ambient temperatures, humidity levels, and light intensity values were monitored as 33.91 ± 2 to 26.95 ± 1%, 45 ± 3 to 24 ± 3℃, 58 ± 2 to 50 ± 4%, and 7160-90 lx, respectively, during the experimental period. The ICT-based monitoring system ensured precise irrigation scheduling and better performance to provide an adequate water supply and information about the ambient environment.

• 예술인문사회 융합 멀티미디어 논문지
• /
• 제7권10호
• /
• pp.895-903
• /
• 2017

양자점 셀룰라 오토마타(QCA)는 CMOS의 근본적인 한계에 대한 대체 해결책으로 제안된 기술 중 하나이다. QCA는 최근 실험 결과와 함께 다양한 연구가 진행해오고 있으며 나노 규모의 크기와 낮은 전력 소비로 각광 받고 있다. 기존 논문에서 제안된 XOR 게이트는 최소한의 면적과 셀의 개수를 이용하여 설계 할 수 있음에도 불구하고 안정성 및 결과의 정확성 때문에 추가된 셀의 개수가 많았다. 본 논문에서는 기존의 XOR 게이트의 단점을 보완한 게이트를 제안한다. 본 논문의 XOR 게이트는 정사각형 구조로 AND 게이트와 OR게이트를 배치함으로써 셀 배선의 개수를 줄인다. 그리고 제안한 XOR 게이트를 이용하여 단순 인버터 역할을 하는 셀 2개를 추가해 반가산기를 제안한다. 또한 본 논문은 입력과 결과의 정확성을 위해 QCADesginer을 이용한다. 따라서 제안한 반가산기는 기존의 반가산기에 비해 더 적은 수의 셀, 전체 면적으로 구성됨으로 큰 회로에 사용할 때 혹은 작은 면적에 반가산기가 필요할 때 효율적이다.