• Proceedings of the KAIS Fall Conference
• /
• 2007.11a
• /
• pp.162-165
• /
• 2007

본 논문에서는 고주파 전류형 인버터의 출력을 제어하기 위하여 입력단의 쵸핑 스위칭 방법을 제안한다. 인버터의 출력제어는 스위칭 소자에 인가되는 구동신호에 위상천이의 크기에 따라 제어하고 있으며, 제한회로의 동작원리를 서술하였다. 또한 회로설계에 필요한 출력특성은 수치해석에 의해 평가자료를 도출하고 실험 장치를 제작하여 이론결과와 비교 검토하여 특성평가의 정당성을 입증하였다.

• Proceedings of the Optical Society of Korea Conference
• /
• 1989.02a
• /
• pp.230-234
• /
• 1989

Pyroelectric TGS(triglycine sulfate) detectors, whose thicknesses are 0.1mm and 0.2 mm, are fabricated using the grown TGS crystals from aqueous solution. The outut power and noise from these detectors are measured as a function of chopping frequency in the range from 10Hz to 160Hz with the interval of 10Hz. Response time, responsivity and detectivity are derived from the measured output power and noise of the detectors. The results show that the response time is about 15ms, resposivity is 100V/W at 10Hz and the detectivity at the maximum spectral wavelength D{{{{ lambda }}P* is about 10 cmHz1/2w-1.

• Polymer(Korea)
• /
• v.34 no.2
• /
• pp.108-115
• /
• 2010

The effects of acid-treated MWCNT and coupling agent on properties of MWCNT/SBR are investigated in this work. The MWCNTs oxidized using sulfuric and nitric acids were analyzed by the Raman scattering and Fourier transformed infrared spectroscopy(FT-IR). The FT-IR results indicate the presence of -COOH groups in the treated samples, and Raman spectroscopy of the acidtreated MWCNTs further corroborates the formation of surface defect due to the introduction of carboxyl groups. And the nanocomposites reinforced with MWCNTs were characterized extensively using the scanning electron microscopy(SEM), electrical conductivity, thermal conductivity, and tensile properties measurements. The results showed that nanocomposites onto acid-treated MWCNTs enhanced mechanical properties compared to those containing MWCNTs without acid treatment. These findings confirmed the improved interfacial interactions between MWCNTs and SBR arising from the coupling agents. But the electrical and thermal conductivity of nanocomposites decreased due to the chopping and formation of surface defects of MWCNTs.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.50 no.9
• /
• pp.456-465
• /
• 2001

In this paper, breakdown voltages in $SF_6-N_2$ mixtures were experimentally investigated to understand characteristics of dielectric strength and physical phenomena in nonuniform field disturbed by a needle shape protrusion. The test voltages are the lightning impulse$(\pm1.2/44 \mus)$ and the damped oscillatory impulse$(\pm400 ns / 0.83 MHz)$ voltages which can be occurred by the operation of disconnecting switches in gas-insulated switchgears(GIS). The effects of the polarity and wave shape of the test voltages, and the gas pressure on the V-t characteristics were in detail examined. The V-t characteristic curves were measured in different two ways : (1) one is the method by taking the maximum voltage recorded at or prior to breakdown against the time to breakdown, that is, the Procedures recommended in IEC 60060-1, (2) the other is the method by taking the voltage at the instant of chopping against the time to breakdown. As a result, the V-t characteristics of $SF_6-N_2$ mixtures in nonuniform electric field were significantly affected by the polarity and wave shape of the applied voltages. The positive breakdown voltages resulted in lower breakdown voltages in the time ranges considered, and the V-t curves for the negative oscillatory impulse voltage were extended over the longer time range. For the lightning impulse voltages, the V-t curves obtained by IEC Pub. 60060-1 were nearly same with the V-t curves obtained by the voltage at the instant of chopping against the time to breakdown. It is clear that the actual breakdown voltages were much lower than the maximum voltages appearing at or prior to breakdown because of the displacement current produced as a result of the dV/dt during the oscillatory transient voltage app1ication. The scattering of the negative actual breakdown voltages was much larger than that of the positive.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.3
• /
• pp.229-235
• /
• 2001

Uncooled pyroelectric thin-film (Ba,Sr)TiO$_3$ infrared detectors thermally isolated from Si-substrate by Si$_3$N$_4$/SiO$_2$/Si$_3$N$_4$-membrane have been fabricated, and figures of merit for detectors were examined. The detector at $25^{\circ}C$ in air showed relatively high voltage responsivity of about 168.8 V/W and low specific detectivity of about 2.6$\times$10$^4$cm.Hz$^{1}$2//W at 1 Hz-chopping frequency because of very small signal-to-noise voltage ratio. It could be found that both thermal noise voltage and thermal time constant of the detector were very large by analyzing dependences of output waveforms on chopping frequency and temperature.

• Asian-Australasian Journal of Animal Sciences
• /
• v.17 no.12
• /
• pp.1758-1763
• /
• 2004

This study was carried out to investigate gel forming and degradation properties (suwari and modori phenomena) of chicken surimi from mechanically deboned chicken meat (MDCM) at various setting temperatures and time. Chicken surimi was manufactured by a continuous process including chopping of MDCM, washing with 5% NaCl solution or pure water, standing, straining and centrifuging etc. Total process of washing for the MDCM from chopping to centrifuging was repeated over 3 cycles. Gel from prepared surimi were formed at $90^{\circ}C$ for 30 min after various setting treatments. The textural properties of gels were measured at the temperature ranges of low (10$^{\circ}C$), medium (25$^{\circ}C$ and $30^{\circ}C$) and high (45 to 70$^{\circ}C$). The compressive force (CF), hardness and fracturability of surimi gel at 10$^{\circ}C$ increased as setting time increased, and showed the highest value at 30 h of setting time. The CF and hardness of chicken surimi gel at 25$^{\circ}C$ and 30$^{\circ}C$ showed the highest values at 10 h of setting time. Most of gel strengths including CF, and texture profile analysis (TPA) values showed the highest levels in the range 47.5 to 52.5$^{\circ}C$ (p<0.05). The gel strength at 60$^{\circ}C$ increased slightly at 30 min, but then continued to decrease with longer setting times. There was no increase of gel strength at $70^{\circ}C$, but only a continuous decrease over setting time. In conclusion, suwari (gel setting) and modori (gel degradation) phenomena occur during the gel formation of surimi from MDCM. The temperature range in chicken surimi was 47.5 to 52.5$^{\circ}C$ for suwari and 60 to 70$^{\circ}C$ for modori.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.10a
• /
• pp.848-851
• /
• 2012

In this paper, circuit of reducing the offset voltage in Op-amp, effectively, is newly proposed by using dual capacitor. Capacitors and MOS switches are added in proposed circuit to make up for the weak points of previous circuits ofr reducing the offset voltage in auto-zeroing method. Also, it is designed to reduce the offset voltage in high frequency range by using chopping method, effectively. Circuit simulation and layout are executed by TSMC 1.8V, 0.18um process. From the simulation results, it is verified that magnitude of offset voltage is under 5mV and proposed circuit is good for compensation of offset voltage better than previous auto-zeroing method.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.2
• /
• pp.202-208
• /
• 2001

A Switched Reluctance Motor(SRM) has double salient poles structure and the phase windings are wound in stator. SRM hase more simple structure that of other motor, thus manufacture cost is low, mechanically strong, reliable to a poor environment such as high temperature, and maintenance cost is low because of brushless. SRM needs position detector to get rotator position information for phase excitation and tachometer or encoder for constant speed operation. But, this paper doesn\`s use an encoder of high cost for velocity measurement of rotator. Instead of it, the algorithm for position detection and velocity estimation from simple slotted disk has been proposed and developed. To implement variable speed digital control system with velocity estimation algorithm, the TMS320F240-20MIPS fixed point arithmetic processor of TI corporation is used. The experimental results of the developing system are enable to control speed with wide range, not only single pulse, hard chopping mode and soft chopping, ut also variable speed control, and advance angle control.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.2 no.1
• /
• pp.27-35
• /
• 1998

In this paper, we propose a novel spectral-chopping model of Class-II$(1+D)^2$ -PRS system which reveals improved spectral efficiency. We build up the model having spectrum chopped by the amount of Nyquist over-rate, and then compare its characteristics with the conventional model in both the time-domain and the frequency-domain. When the transmission system operates above the Nyquist rate, the new model has better performance than the conventional PRS using its inherent speed-tolerance. According to our investigations, Class-II PRS shows more excellent effect in the spectral-chopping method than Class- I and W types analyzed previously. We ascertain that the over-rate of 26.675 obtained by the inherent speed-tolerance could be improved upto 40% using spectrum-truncation. These effects come from the fact that the raised-cosine spectrum of Class-II PRS has smaller Boss of frequency component and energy than any other types for the same amount of truncation. In order to validate these theoretical results, we present their sidelobe-trends confirming cancellation effects at the sampling instants and some experimental results showing their patterns of eye-openings and spectra.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.2
• /
• pp.109-116
• /
• 2016

Sensing module of standing and moving human body using shutter method was developed. The module consists of Fresnel lens, pyroelectric infrared (PIR) sensor, interface circuit of the PIR, micro control unit(MCU), and alarm light emitting diode(LED). The principle for standing human body is chopping the thermal of human body using camera shutter. The human sensing signal in MCU by algorithm of interrupt function is detected. By unifying an apparatus and print circuit board(PCB), the developed module can be replaced as commercial moving human body detector. Experiment results show that sensing distance is about 7.0m and sensing angles is about $110^{\circ}$ at room temperature. In these condition, sending ratio was 100% and the power dissipation of the module was 100mW.